Asus MD300 Mice and Mouse Pads User Manual
MD300 Mouse
Mouse Model Name: MD300
Dongle Model Name: MD300-D
Your package includes:
a. MD300 Mouse
b. Nano USB 2.4GHz receiver (stored inside the mouse)
c. USB Type-C to Type A cable
d. USB Type-C female to Type-C female adaptor
e. Quick Start Guide
f. Warranty
Card Dimensions
Mouse: 118 (L) x 73 (W) x 43 mm (H)
Dongle: 19 (L) x 12 (W) x 4.5 mm (H)
Weight
Mouse: 111 g
Dongle: 1.6 g
Resolution 1000~4200 DPI
Rating
Mouse: 2.4GHz
mode: 5V/500mA Bluetooth 5.0 mode: 5V/500mA
Dongle: 5V/100 mA
Hardware Version
Mouse: GFSK / Bluetooth: VA
Dongle: GFSK: VA
Software Version
Mouse: GFSK / Bluetooth: V024
Dongle: GFSK: V0163
System Requirements Windows 10 or Above
Operating Temperature 0 ~ 40°C
Storage Temperature -40 ~ 60°C
UKCA RF Output table (The Radio Equipment Regulations 2017)
Frequency Band
Mouse: 2.4GHz mode: 2403~2480 MHz
Bluetooth mode: 2402~2480 MHz
Dongle: 2403~2480 MHz
Maximum output power(EIRP)
Mouse: 2.4GHz mode: 0 dbm
Bluetooth mode: 0 dbm
Dongle: 4 dbm
CE RED RF Output table (Directive 2014/53/EU)
Frequency Band
Mouse: 2.4GHz mode: 2403~2480 MHz
Bluetooth mode: 2402~2480 MHz
Dongle: 2403~2480 MHz
Maximum output power(EIRP)
Mouse: 2.4GHz mode: 0 dbm
Bluetooth mode: 0 dbm
Dongle: 4 dbm
Connecting to PC
Via 2.4GHz:
- Slide the power switch to 2.4GHz Mode.
- Insert the Nano USB receiver into an available USB port on your PC.
Via Bluetooth:
- Slide the switch to Bluetooth Mode.
- Hold the pairing button for over 3 seconds till the indicator LED flashes white.
- On Windows, right-click the Bluetooth icon on the right of the task bar (or double-click the Bluetooth icon in the Control Panel), then click Add a device > ASUS MD300 > Finish.
- When successfully connected, the indicator will stop flashing and turn off. Once the mouse is set up on your PC, it will automatically connect to your PC the next time you turn to Bluetooth mode.
- You may set up your ProArt mouse Bluetooth connection to up to three devices.
- Once set up, you may use the pairing button to switch between the three devices.
NOTE: The mouse supports Bluetooth 5.0.
Updating the firmware
- Connect your ProArt mouse to your computer using the bundled cable, then connect the USB dongle to a USB port.
- Download and install the Armoury Crate from http://www.asus.com/supportonly/Armoury%20Crate/HelpDesk_Download/.
- Follow the software instructions to update your ProArt mouse and dongle’s firmware.
Customizing ProArt mouse using Armoury Crate
Armoury Crate allows you to customize various functions including the buttons, side scroll wheel, dial, DPI, polling rate, low power warning, and more. For detailed instructions on ASUS Dial, please refer to the video tutorial from https://www.youtube.com/watch?v=elsY-cf09g4.
Low battery indicator
Use the bundled USB Type-C to Type-A cable to charge your ProArt mouse when the indicator flashes red. You may customize the indicator to light up alert at the percentage you prefer using Armoury Crate.
Replacing the switches
Lithium-Metal Battery Warning
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
ProArt mouse is compatible with Omron D2FC-F-K switch.
NOTE: ProArt mouse uses special coating that prolongs the longevity of the mouse. You may simply wipe off with finger tip if you see any light scratches on surface.
Notices
This is a Class B product, in a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components, as well as the packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for the detailed recycling information in different regions.
Care during use
- Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery can result in an explosion;
- Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas;
- A battery subjected to extremely low air pressure may result in an exposion or the leakage of flammable liquid or gas.
Simplified UKCA Declaration of Conformity
ASUSTeK Computer Inc. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of The Radio Equipment Regulations 2017 (S.I. 2017/1206).Full text of UKCA declaration of conformity is available at https://www.asus.com/support/.
Simplified EU Declaration of Conformity
ASUSTeK Computer Inc. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Full text of EU declaration of conformity is available at https://www.asus.com/support/.
India E-waste (Management) Rules 2016
This product complies with the “India E-Waste (Management) Rules, 2016” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls(PBBs) and polybrominated diphenyl ethers (PBDEs) in concentrations exceeding 0.1 % by weight in homogenous materials and 0.01 % by weight in homogenous materials for cadmium, except for the exemptions listed in Schedule II of the Rule.
ASUS products sold in Vietnam, on or after September 23, 2011, meet the requirements of the Vietnam Circular 30/2011/TT-BCT.
Regional notice for Singapore
Complies with IMDA Standards DB103778
This ASUS product complies with IMDA Standards.
There are no restrictions of using this product in EU.
EAC Certification Logo
Ukraine Certification Logo
Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does not cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION! Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.
RF exposure warning
The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment. The equipment must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC COMPLIANCE INFORMATION
Per FCC Part 2 Section 2.1077
Responsible Party: Asus Computer International
Address: 48720 Kato Rd, Fremont, CA 94538.
Phone/Fax No: (510)739-3777/(510)608-4555 hereby declares that the product
Product Name : MD300 Mouse, ProArt Mouse
Model Number : MD300 (Mouse), MD300-D (Dongle) compliance statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Ver. 180620
Manufacturer
ASUSTeK Computer Inc.
Address: 1F., No. 15, Lide Rd., Beitou Dist., Taipei City 112, Taiwan
Tel: +886-2-2894-3447
Authorised representative in Europe
ASUS Computer GmbH
Address: HARKORT STR. 21-23, 40880 RATINGEN, GERMANY Authorized representative in United Kingdom
ASUSTeK (UK) LIMITED
Address: 1st Floor, Sackville House, 143-149 Fenchurch Street, London, EC3M 6BL, England, United Kingdom