Miele PRI 214 Plan Commercial Flatwork Ironer Installation Guide

Miele PRI 214 Plan Commercial Flatwork Ironer

Installation and planning notes

Installation requirements

• This flatwork ironer must be installed in accordance with all relevant regulations and standards. Local energy supplier regulations must also be observed.
• This flatwork ironer must only be operated in a room that has sufficient ventilation and which is frost-free.

Storage

The following conditions must be observed for transport and storage of this flatwork ironer:

• Ambient temperature: -25 °C to +55 °C
• Humiditiy: 5 % to 75 %, non-condensing
• Maximum storage period: 2 years

• Ambient temperature: +5 °C to +40 °C
• Humidity: 10 % to 85 %
• At 21 °C ambient temperature, the maximum permissible relative humidity is 70 %.

Setting up

This ironer must be transported to its installation site using a suitable pallet truck. Do not remove the packaging until immediately before the ironer is commissioned.

Lift the ironer off the wooden pallet at its installation site only. The clamps on the side columns must first be removed. They can be reused after setting the ironer up to secure it to the floor (see “Floor anchoring).
The suspension points for lifting hooks/straps are located under the side columns between the screw-on feet.
During installation, remember that the clearance next to and behind the machine columns must amount to at least 600 mm so that the side cladding remains accessible. The ironer should be set up so that the light shines parallel to the infeed table as much as possible.
The clearance in front of the ironer must amount to at least 1.5 m to prevent foreign materials (furniture, walls) getting hot.  There should be a clearance of at least 1 m above the ironer.
A base and anchoring means are not necessary.

Levelling

• Dismantle the mounting flaps on the left and right sides.
• Align the roller and the side columns using the screw feet and a spirit level. The screw feet under the side columns can be unscrewed to a maximum of 60 mm.
• After levelling the machine secure the screw feet so they cannot come loose.

Floor anchoring

A suitable anchoring kit for the ironer is available to purchase from Miele. Alternatively the clamps that were used for securing the machine to the wooden pallet can be used for securing it to the floor.

Electrical connection

In the event of unfavourable mains conditions, the flatwork ironer may lead to interfering voltage fluctuations. If the mains impedence is greater than 0.175 Ohm at the connection point to the mains supply, additional measures may be required before the machine can be properly operated at this connection point. The mains impedence can be requested from your power supply company.

The electrical equipment on this flatwork ironer complies with the following standards: IEC/EN 60204-1, IEC/EN 60335-1, IEC/ EN 60335-2-44, EN ISO 10472-1 and EN ISO 10472-5.

For hard-wired machines, an all-pole means of deactivation must be provided on site. Switches with a minimum contact gap greater than 3 mm are suitable disconnectors. These include circuit breakers, fuses, and contactors (VDE 0660).
The plug connectors or isolator switch should be easily accessible for servicing work.
If the flatwork ironer is disconnected from the electricity supply ensure adequate measures are taken to ensure that the machine cannot be reconnected to the electricity supply until all work has been carried out.
If it is necessary to install a residual current device (RCD) in accordance with the local regulations, a residual current device type A can be used.

Exhaust ducting

The moist-warm exhaust air is to be conducted to the outside or into a suitable venting duct over the shortest path possible. Due to the higher air velocity, the exhaust ducting must be laid in such a way that air flow is not hindered (few bends, short lines, well-made connections and transitions). Filters and louvres may not be installed in the exhaust ducting.
Since the relative humidity can amount to up to 100%, suitable measures must be taken to prevent condensate from flowing back into the ironer. If the machine fan is not powerful enough to remove the moist air, a suitably powerful additional fan must be installed in the shaft or roof outlet on-site. Supply air must be provided to the room of installation according to the amount of exhaust air.

• The connection for the exhaust air ducting for vapour extraction is located on the rear of the left side column and has a diameter of 70 mm (HT DN 70).
• The exhaust ducting must have an internal diameter of 70 mm (HT DN 70).
• If the exhaust ducting rises upwards, a condensate drain hole with a diameter of 3 ­ 5 mm must be provided at the lowest point.
• Adequate ventilation of the installation room must be ensured.
• The ducting system and the exit point to the outside must be checked on a regular basis for a build-up of lint and cleaned if required.
• The end of ducting leading into the open should be protected against the elements, e.g. with a downward facing 90° bend.

Substitute pipe lengths

According to the number of bends, the substitute pipe lengths must be deducted from the maximum permissible pipe length.

Maximum permissible total pipe length

Optional accessories

Plinth UG 1200

The ironer can be raised 100 mm by fitting the optionally available plinth UG 1200.

Payment system

This ironer can be fitted with an optional payment system (e.g. for use in a launderette). Miele Service have to programme a setting in the machine’s electronics and connect the payment system. Miele offer payment systems for coin-free operation as well as payment systems with mechanical or electronic coin boxes for specific target groups.

Dimensions / Installation

➀ Electrical connection ➁ Exhaust connection

Technical data

PRI 214 EL D 3NAC 400V 50-60Hz

¹ Operating class: gG; ² Minimum cross-section according to VDE 0298-4; ³ At 100% occupation + 25% residual moisture

Granted test certificate: VDE, see data plate; applied product safety standards: IEC/EN 60204-1, IEC/EN 60335-1, IEC/EN 60335-2-44, EN ISO 10472-1, EN ISO 10472-5

Miele & Cie. KG
Carl-Miele-Straße 29
33332 Gütersloh
Germany
Telefon: 05241 89-0
Telefax: 05241 89-2090
Internet: www.miele.com/professional