SEALEY SM47.V3 DUST & CHIP EXTRACTOR 2HP User Manual
DUST & CHIP EXTRACTOR 2HP
MODEL NO: SM47.V3
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT IS CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY WILL INVALIDATE THE WARRANTY.
SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before use. Inspect power supply leads, plugs, and all electrical connections for wear and damage. Sealey recommends that an RCD (Residual Current Device) is used with all electrical products. You may obtain an RCD by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance Test) tested.
For electrical safety information, it is important that the following information is read and understood.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct fuse – see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
DO NOT pull the plug from the socket by the cable.
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or is replaced immediately by a qualified electrician. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch off the electricity supply and remove it from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommends that repairs are carried out by a qualified electrician.
1.1.1. Cable extension reels. When a cable extension reel is used it should be fully unwound before connection. A cable reel with an RCD fitted is recommended since any product which is plugged into the cable reel will be protected. The section of the cable on the cable reel is important. We recommend at least a 1.5mm² section cable but to be absolutely sure that the capacity of the cable reel is suitable for this product and for others that may be used in the other output sockets, we recommend the use of 2.5mm²
section cable.
1.2. GENERAL SAFETY
- WARNING! Disconnect the extractor from the mains power and ensure the impeller is at a complete standstill before attempting to
change accessories, service or perform any maintenance. - Maintain the extractor in good condition (use an authorized service agent).
- Replace or repair damaged parts. Use genuine parts only. Non-genuine parts may be dangerous and will invalidate the warranty.
- Locate the extractor in a suitable working area. Ensure the surface is flat and firm. Keep the area clean and tidy and free from unrelated materials, and ensure there is adequate lighting. Keep the extractor clean for best and safest performance and check moving parts alignment regularly.
- Remove any tools from the extractor and the vicinity before turning it on.
- WARNING! Wear approved safety eye protection, ear defenders, gauntlets, and, if dust is generated, respiratory protection.
- Remove ill-fitting clothing. Remove ties, watches, rings, and other loose jewelry and contain long hair.
- Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
- Keep children and unauthorized persons away from the working area.
- DO NOT use the extractor for any purpose other than that for which it is designed. DO NOT pick up metal, glass or water.
- DO NOT allow untrained persons to operate the extractor.
- DO NOT get the unit wet or used in damp or wet locations or areas where there is condensation.
- WARNING! DO NOT use extractors where there are flammable liquids, solids, or gases such as petrol, paint solvents, waste rags etc.
- DO NOT operate the extractor if any parts are missing or damaged as this may cause failure and/or personal injury.
- DO NOT operate the extractor when you are tired or under the influence of alcohol, drugs or intoxicating medication.
- When not in use switch the extractor off and isolate it from the power supply.
INTRODUCTION
Mobile workshop extractor suitable for attachment to most static workshop machines including bandsaws, table saws, scroll saws, planers and sanders. Supplied with 2m of Ø100mm suction ducting.
SPECIFICATION
Model no ……………………………………………………….. SM47.V3
Airflow ……………………………………………………………… 618cfm
Flex hose diameter …………………………………………….. 100mm
Flex hose length ………………………………………………… 200mm
Impeller diameter ………………………………………………. 250mm
Intake diameter …………………………………………………. 125mm
Motor power ……………………………………………………….1500W
Supply ………………………………………………………………….230V
| Collector Body with Motor | Filter/Collector Bag x 2 |
| Seal | Support, Collector x 3 |
| Base plate | Screws, Nuts, Washers (1 bag) |
| Hose | Inlet |
| Hose Clamp x 2 | Bag Clamp x 2 |
| Collector | Inlet Hose (2m) |
| Support Rod, Filter Bag Outlet | Castors x 4 |
ASSEMBLY
Note: Numbers in brackets are the item numbers on the parts diagram and in the parts list.
5.1. Attach the four castors (1) to the underside of the base (3) using screws (23), washers (16), and nuts (19). Support base (3) on battens, or similar, to raise castors clear of the floor to give stability for the following assembly tasks.
5.2. With screws (6) and washers (4) attach motor base (5) to base (3).
5.3. Attach motor (8) to motor base (5), so that the collector body is positioned as shown in the parts diagram, with screws (6) and washers (4).
5.4. Attach fan housing (38) feet to the base plate (3) with screws (6) and washers (4).
5.5. Install outlet (30) to fan housing (38) using packing (29), screws (15), washers (16), and nuts (19).
5.6. Attach collector supports (37) to the base with screws (12) and washers (4) and to a collector (33) with screws (6) and washers (4). Note that upper bag support (13) is fitted to the collector (33) with the same screws as the collector support (37).
5.7. Fit (upper) filter bag (35) over upper bag flange on the collector (33) and secure by tightening the built-in strap. Hook loop on the end of the bag (35) over the support arm (13). Fit second (collector) bag (36) to lower bag flange on the collector.
Note: Bag clamps (34) are provided and may be used for additional bag security.
5.8. Install hose (32) between outlet (30) and collector (33) and retain with hose clamps (31).
5.9. Push-fit inlet (24) to inlet cover (25)
OPERATION
WARNING! Before operating the extractor ensure that you read, understand, and apply the safety instructions in Section 1.
6.1. Confirm that the supply voltage matches the voltage shown on the motor data plate and that the motor switch (9) is ‘Off’.
6.2. Connect extractor hose (39) to the inlet (24) and attach another end to the extractor point on the equipment. If only one extractor hose is to be used ensure that the unused inlet is closed with the cap provided.
WARNING! DO NOT operate the extractor without the hose(s) attached.
6.3. Plug into the mains supply and press the motor switch ‘On’.
6.4. Ensure that the lower bag is emptied of dust and chips on a regular basis and is not allowed to become full.
Note: Fitting a reducer to the extraction hose will reduce the volume of dust extracted.
WARNING! This unit is not suitable to be used to extract dust via a piped system.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling center, and disposed of in a manner that is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team on or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
