Husqvarna 150BT Gas Backpack Leaf Blower in the Gas User Manual
Husqvarna 150BT Gas Backpack Leaf Blowerin the Gas User Manual
Introduction
Product description
This product is a backpack blower with a fuel engine.
We have a policy of continuous product development and therefore reserve the right to modify the design and appearance of products without prior notice.
Intended use
Use the product to blow leaves and other unwanted material from areas such as lawns, pathways and asphalt roads.
Product overview
(Fig. 1)
- Throttle control lever
- Frame
- Harness
- Engine cover
- Fan cover
- Air intake screen
- Air filter
- Starter rope handle
- Fuel tank
- Waist belt
- Spark plug
- Vibration damping system
- Choke control
- Control handle
- Stop switch with throttle control
- Throttle trigger
- Pipe angle
- Clamp
- Flexible hose
- Control pipe
- Cable clamp
- Intermediate pipe
- Blower nozzle
- Operator’s manual
- Combination wrench
- Air purge bulb
- High speed nozzle
- Idle adjustment screw
- Fan
- Foot plate
Symbols on the product
(Fig. 2) WARNING! This product can be dangerous and cause serious injury or death to the operator or others. Be careful and use the product correctly.
(Fig. 3) Read the operator’s manual carefully and make sure that you understand the instructions before use.
(Fig. 4) Use approved hearing protection and approved eye protection. If the environment contains dust, use a breathing mask.
(Fig. 5) Use approved protective gloves during operation and maintenance. Use protective boots or shoes with non-slip soles. Use clothing of strong fabric and of full length.
(Fig. 6) Make sure that long hair is put above your shoulders.
(Fig. 7) Do not wear jewelry or loose clothing during operation.
(Fig. 8) Mixture of gasoline and two-stroke oil.
(Fig. 9) Air purge bulb.
(Fig. 10) Keep all body parts away from hot surfaces.
(Fig. 11) Do not go near the impeller as it turns.
(Fig. 12) Choke, open position.
(Fig. 13) Choke, closed position.
(Fig. 14) Idle adjustment screw.
(Fig. 16) Look out for thrown objects. Thrown objects can cause serious injury. Use personal protective equipment.
(Fig. 17) Keep a safety distance at a minimum of 15 m to persons or animals.
yyywwxxxxx The rating plate or the laser printing shows the serial number. yyyy is the production year and ww is the production week.
Note: Other symbols/decals on the product refer to certification requirements for other commercial areas.
California Proposition 65
(Fig. 18)
EPA III
(Fig. 15)
The Emissions Compliance Period referred to on the Emission Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal emissions requirement. Maintenance, replacement or repair of the emission control devices and system may be performed by any non-road engine repair establishment or individual.
Safety
Safety definitions
The definitions below give the level of severity for each signal word.
Note: This information makes the product easier to use.
General safety instructions
- Do not do changes to the product without approval from the manufacturer and always use original accessories. Modifications and/or accessories that are not approved can result in serious injury or the death of the operator or others.
- Do not use a damaged product. Do the safety checks and maintenance given in this operator’s manual. All other maintenance must be done by approved servicing personnel.
- All servicing and repair operations must be done by approved servicing personnel. If a part of the product is defective, speak to your servicing dealer.
Vibration safety
This product is for occasional operation only. Continuous or regular operation of the product can cause “white finger” or equivalent medical problems from vibrations. Examine the condition of your hands and fingers if you operate the product continuously or regularly. If your hands or fingers have discoloration, have pain, tingle, or are numb, stop work and speak to a physician immediately.
Safety instructions for operation
- This product can be dangerous and cause serious injury or death to the operator or others. Be careful and use the product correctly.
- Do an inspection of the product before use. Refer to Maintenance on page 12.
- Do not operate the product when you are tired, ill or under the influence of alcohol or other drugs that can decrease your vision, judgment or coordination.
- Install all covers and guards before use. To prevent electrical shock, make sure that the spark plug cap and ignition cable are not damaged.
- Do not touch the spark plug or ignition cable when the engine is on.
- Keep a safety distance at a minimum of 15 m to persons or animals. If persons, children or animals come nearer than 15 m, stop the product. Point the product away from persons, animals, open windows and other objects.
- Do not let children operate the product. Make sure that all operators read and understand the contents of this operator’s manual.
- Keep hands or other objects away from the blower housing during operation. Rotating parts can cause serious injury.
- Do not use the product if the air intake screen is not installed. Always make sure that the air intake screen is installed and not damaged before use.
- If an emergency occurs, release the waist belt and chest belt of the harness and let the product fall.
- Obey national regulations and directives.
- Keep all body parts away from hot surfaces.
- Too much vibration can cause damage to the circulation or the nervous system. Speak to your physician if you have symptoms, for example numbness, loss of feeling, tingling, pricking, pain, loss of strength or changes in skin color in your fingers, hands or wrists.
- Look out for thrown objects. Thrown objects can cause serious injury.
- Do not use the product in bad weather, for example fog, rain, strong winds and too cold environments. To do work in bad weather can cause tiredness and dangerous conditions.
- Make sure that you can move and keep a stable position. Do a check of the work area for possible obstacles, for example rocks. Be careful if you operate the product on a slope.
- Do not put the product on the ground with the engine on.
- Do not operate the product from high positions, for example on a ladder.
- Make sure that you can always be heard if an accident occurs.
- Make sure that the exhaust fume outlet is not blocked. To prevent damage to the product, keep obstacles at a minimum distance of 50 cm from the exhaust fume outlet.
- Do not start the product indoors, in bad airflow or near flammable material. The engine exhaust fumes contain carbon monoxide, which can cause carbon monoxide poisoning. The engine exhaust fumes are hot and can contain sparks which can start a fire.
Personal protective equipment
- Use approved personal protective equipment when you use the product. Personal protective equipment cannot fully prevent injury but it can decrease the degree of injury. Speak to your dealer for more information.
- Use approved hearing protection. Long-term exposure to noise can result in permanent hearing damage.
- Use approved eye protection. If you use a visor, you must also use approved protective goggles. Approved protective goggles must agree with the ANSI Z87.1 standard in the USA or EN 166 in EU countries.
- Use protective gloves during operation and maintenance.
- Use protective boots or shoes with non-slip soles.
- Use clothing of strong fabric and of full length. Do not use jewelry or open shoes. To decrease the risk on injury, your clothing must be close-fitting but not limit your movements. Put your hair above your shoulders to prevent that your hair enters rotating parts or catches on branches.
- Use breathing protection when there is a risk of dust.
- Keep first aid equipment near.
Safety devices on the product
- Do not use a product with defective safety devices.
- Do a check of the safety devices regularly. Refer to Maintenance on page 12.
- If the safety devices are defective, speak to your Husqvarna servicing dealer.
To do a check of the muffler
- Regularly do a visual check of the muffler. The muffler keeps noise levels to a minimum and sends exhaust fumes away from the operator. Refer to To examine and clean the cooling system on page 13.
To do a check of the vibration damping system
- Make sure that there are no cracks or deformation on the vibration damping units.
- Make sure that the vibration damping units are correctly attached to the engine unit and handle unit.
Refer to Product overview on page 6 for information about where the vibration damping system is on your product.
To do a check of the start/stop switch
- Use the start/stop switch to stop the engine.
- Make sure that the engine stops fully.
To see where the start/stop switch is on your product, refer to Product overview on page 6.
Harness safety
Always use the harness when you operate the product. If you do not use the harness, you cannot operate the product safely. This can result in injury to you or other persons. Make sure that the waist belt and chest strap are attached and correctly adjusted. There is a risk that an open belt can go into the fan of the product.
(Fig. 19)
Fuel safety
- Do not mix or add the fuel indoors or near a heat source.
- Do not start the product if there is fuel or oil on the product or on your body.
- Do not start the product if the engine has a fuel leak. Examine the engine for fuel leaks regularly.
- Always be careful with fuel. Fuel is flammable and the fuel fumes are explosive and can cause serious injury or death.
- Do not breathe in the fuel fumes, it can cause injury. Make sure that there is a sufficient airflow.
- Do not smoke near the fuel or the engine.
- Do not put the product or a fuel container near warm objects, an open flame, a spark or a pilot light.
- Always use approved containers for storage and transportation of fuel.
Safety instructions for maintenance
- Stop the engine, remove the spark plug and let the engine become cool before maintenance and assembly.
- A blocked spark arrestor screen causes the engine to become too hot which causes damage to the engine.
- If the spark arrestor screen is frequently blocked, it can be a sign that performance of the catalytic converter is decreased. Speak to your servicing dealer to examine the muffler.
Assembly
Introduction
To assemble the blower pipe and the control handle on the product
Note: Lubricate the tubes and flexible hose to make them easier to assemble.
- Attach the flexible hose (A) to the pipe angle and the control pipe (B) with the clamps (C) and (D). (Fig. 20)
- Attach the handle holder (E) to the control pipe. Align the handle holder with the flange on the control pipe. (Fig. 21)
- Adjust the position of the control handle to a safe and correct work position. Tighten the knob.
- Attach the cable to the flexible hose with the cable clamp. (Fig. 22)
- Attach the intermediate pipe to the control pipe. (Fig. 23)
- Attach the blower nozzle to the intermediate pipe.
Note: The blower nozzle can only be installed on the intermediate pipe. - For higher air speed, attach the high speed nozzle to the blower nozzle.
Operation
Introduction
Fuel
This product has a two-stroke engine.
Premixed fuel
- Use Husqvarna premixed alkylate fuel for best performance and extension of the engine life. This fuel contains less harmful chemicals compared to regular fuel, which decreases harmful exhaust fumes. The quantity of remains after combustion is lower with this fuel, which keeps the components of the engine more clean.
To mix fuel
Gasoline
- Use good quality unleaded gasoline with a maximum of 10% ethanol contents.
Two-stroke oil
- For best results and performance use Husqvarna two-stroke oil.
- If Husqvarna two-stroke oil is not available, use a two-stroke oil of good quality for air-cooled engines. Speak to your servicing dealer to select the correct oil.
To mix gasoline and two-stroke oil
(Fig. 24)
- Fill half the quantity of gasoline in a clean container for fuel.
- Add the full quantity of oil.
- Shake the fuel mixture.
- Add the remaining quantity of gasoline to the container.
- Carefully shake the fuel mixture.
To fill the fuel tank
- Stop the engine and let the engine become cool.
- Clean the area around the fuel tank cap. (Fig. 25)
- Shake the container and make sure that the fuel is fully mixed.
- Remove the fuel tank cap slowly to release the pressure.
- Fill the fuel tank.
- Tighten the fuel tank cap carefully.
- Clean fuel spillage on and around the product.
- Move the product 3 m/10 ft or more away from the refuelling area and fuel source before you start the engine.
Note: To see where the fuel tank is on your product, refer to Product overview on page 6.
To start a cold engine
- If the engine is cold, put the choke control (A) to the closed choke position. Refer to Symbols on the product on page 6. (Fig. 26)
- Push the air purge bulb (B) again and again for a minimum of 10 times and fuel starts to fill the air purge bulb. It is not necessary to fill the air purge bulb fully.
- Put the throttle control in the fast idle position. Align the guide marks on the throttle control lever and the control handle. (Fig. 27)
- Put the product on a flat surface on the ground.
- Hold the product with the left hand and put your foot on the foot plate. (Fig. 28)
- Pull the starter rope handle slowly with the right hand until resistance occurs.
Note: Do not pull the starter rope handle to full extension and do not let go of the starter rope handle. - Pull the starter rope handle quickly with the right hand until the engine starts or attempts to start, maximum 6 times. If the engine starts, move the choke lever gradually to the open position and continue to step 11. If the engine does not start, continue to step 9.
- When the engine attempts to start, move the choke lever gradually to the open position.
- Pull the starter rope handle quickly with the right hand until the engine starts, maximum 6 times.
- Let the engine run for 30 seconds.
- Put the throttle control at idle speed. (Fig. 29)
- Push the throttle trigger to adjust the blower speed. Refer to To use the throttle trigger on page 12.
To start a warm engine
- If the ambient temperature is below 32°C / 90°F, use the same starting procedure as To start a cold engine on page 11 but do not put the choke control in the closed choke position.
- If the ambient temperature is above 32°C / 90°F, use the same starting procedure as To start a cold engine on page 11.
To use the throttle trigger
- To increase the blower speed during operation, push the throttle trigger until you get the correct speed. (Fig. 30)
- To decrease the blower speed during operation, release the throttle trigger until you get the correct speed.
To start the engine when the fuel is too hot
If the product does not start, the fuel can be too hot.
Note: Always use new fuel and decrease the operation time during warm weather.
- Put the product in a cool area away from open sunlight.
- Let the product cool down for 20 minutes at minimum.
- Press the air purge bulb again and again for 10-15 seconds.
- Obey the procedure to start a cold engine. Refer to To start a cold engine on page 11.
To operate the product
- Operate the product at usual work hours. Obey local regulations.
- Decrease the pieces of equipment and select the correct speed for your task. Use the throttle at lowest position possible to prevent more noise and dust than necessary.
- Keep the blower nozzle near the ground.
Note: Husqvarna recommends that you use the full blower nozzle extension.
- Make a note of the wind direction and operate the product in the direction of the wind.
- Use applicable garden tools to release material from the ground.
- In areas with dust, use spray equipment to wet the area. This decreases the operation time.
- After operation, keep the product in storage vertically.
To stop the product
- Push the stop switch. (Fig. 31)
Note: When the product stops, you can hear a knock sound. This is typical and is not an indication of a defective product.
To adjust the harness
- Put on the harness of the product.
- Put the waist belt around your waist and connect the belt buckle for the waist strap. (Fig. 32)
- Tighten the waist belt strap. (Fig. 33)
- Connect the belt buckle for the chest strap. (Fig. 34)
- Adjust the position of the chest strap. (Fig. 35)
- Tighten the chest strap. (Fig. 36)
- Tighten the shoulder straps until the product is tight against your body. (Fig. 37)
- Tighten the load lifter straps. (Fig. 38)
Maintenance
Introduction
Maintenance schedule
To adjust the idle speed
- Make sure that the air filter is clean and that the air filter cover is attached.
- Adjust the idle speed with the idle speed screw. To see where the idle speed screw is on your product, refer to Product overview on page 6.
To do a check of the spark plug
- Stop the engine and let the product become cool.
- Clean the spark plug if it is dirty.
- Make sure that the electrode gap is correct. Refer to Technical data on page 16. (Fig. 39)
- Replace the spark plug monthly or more frequently if it is necessary.
To do maintenance on the muffler
- Clean the spark arrestor screen on the muffler. Use a wire brush. (Fig. 40)
- Let a servicing dealer replace or do service on the muffler and the spark arrestor screen after 50 hours of operation.
To examine and clean the cooling system
The cooling system includes the cooling fins on the cylinder and the air intake screen.
- Stop the engine.
- Make sure that the cooling system is not dirty or blocked. If it is necessary, clean the air intake screen and cooling fins.
- Examine the cooling system for damages. Make sure that the parts are attached correctly to the product.
To clean the air filter
- Push the choke control to the closed position.
- Remove the air filter cover (A).
- Remove the pre-filter (B) from the air filter cover. (Fig. 41)
- Remove the air filter (C) from the filter frame.
- Clean the pre-filter and the air filter with warm water and soap.
Note: An air filter that has been used for a long time cannot be fully cleaned. Replace the air filter regularly and always replace a defective air filter. - Clean the inner surface of the air filter cover (A) with a brush.
- Put the air filter in the filter frame.
- Attach the pre-filter to the air filter cover.
- Attach the air filter cover to the product.
Troubleshooting
Transportation and storage
- Empty the fuel tank before transportation or long-term storage. Push the air purge bulb to make sure that all fuel is removed. Discard the fuel at an applicable disposal location.
- Make sure that the product is clean and that a full servicing is done before long-term storage.
- Remove the spark plug and put approximately 15 ml of two-stroke oil into the cylinder. Turn the product 3 times and install the spark plug again.
- Attach the product safely to the vehicle during transportation.
- Keep the product in a dry, cool and clean space with good airflow. Keep the product away from children.
Technical data
Original instructions
