Philips TAT5506 5000 Series True Wireless Headphones User Manual

PHILIPS TAT5506 5000 Series True Wireless Headphones

Register your product and get support at www.philips.com/support

 Important safety instructions

Hearing safety

Danger
To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is.

Be sure to observe the following guidelines when using your headphones.

•  Listen at reasonable volumes for reasonable periods of time.
•  Be careful not to adjust the volume continuously upwards as your hearing adapts.
•  Do not turn up the volume so high that you can’t hear what’s around you.
•  You should use caution or temporarily discontinue use in potentially hazardous situations.
•  Excessive sound pressure from earpieces and headphones can cause hearing loss.
• Using headphones with both ears covered while driving is not recommended and may be illegal in some areas.
•  For your safety, avoid distractions from music or phone calls while in traffic or other potentially dangerous environments

General information To avoid damage or malfunction:

•  Do not expose headphones to excessive heat.
• Do not drop your headphones.
•  Headphones shall not be exposed to dripping splashing. (Refer to the IP rating of spec product)
•  Do not allow your headphones to be submerged in water.
• Do not charge your headphones when the connector or socket is wet.
• Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives.
• If cleaning is required, use a soft cloth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product.
• The integrated battery shall not be exposed to excessive heat such as sunshine, re or the like.
• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
• To achieve the specic IP rating, the charging slot cover must be closed.
• Disposal of a battery into re or a hot oven, or mechanically crushing or cutting a battery, can result in an explosion.
• Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas.
• A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.

Operating and storage temperatures and humidity

•  Store in a place where the temperature is between -20°C (-4°F) and 50°C (122 °F) up to 90% relative humidity.
• Operate in a place where the temperature is between 0°C (32°F) and 45°C (113 °F) up to 90% relative humidity.
• Battery life may be shorter in high or low-temperature conditions.
•  Replacement of a battery with an incorrect type risks severely damaging the headphones and the battery (for example, in the case of some lithium battery types).

Your True wireless earpieces

What’s in the box Philips True wireless earpieces Philips TAT5506 Replaceable rubber ear caps x 3 pairs Congratulations on your purchase, and welcome to Philips! To fully benet from the support that Philips offers, register your product at www.philips.com/support. With these Philips True wireless earpieces you can:

•  Enjoy convenient wireless hands-free calls
•  Enjoy and control music wirelessly
• Switch between calls and music

What’s in the box

• Philips True wireless earpieces Philips TAT5506
  

  

• Replaceable rubber ear caps x 3 pairs
• USB-C charging cable (for charging only)

Other devices
A mobile phone or device (e.g. notebook, tablet, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible with the earpieces.

Overview of your True wireless earpieces

1. Microphone
2. Multi-function touch (MFT)
3. LED indicator (earpieces)
4. Microphone
5. LED indicator (factory reset)
6. Factory reset button
7. USB-C charging slot
8. LED indicator (charging box)

Get started

Charge the battery

Note

• Before you use your headphones, place them in the charging box and charge the battery for 2 hours for optimum battery capacity and lifetime.
• Use only the original USB-C charging cable to avoid any damage.
• Finish your call before charging. Connecting the earpieces to charge will power them off.

Charging Box
Plug one end of the USB-C cable into the charging box and the other end into the power source.

Tip
The charging box serves as a portable backup battery for charging the earpieces. When the charging box is fully charged, it will fully recharge the earpieces 3 times.

Earpieces
Place the earpieces in the charging box.

•  The earpieces start charging and the blue LED light goes on
•  When the earpieces are fully charged, the blue light will go off

Tip

Normally, a full charge takes 2 hours (for the earpieces or charging box) by USB cable.

Wireless charging
(Wireless charger is not included)
The charging box has a built-in wireless charging coil. You can charge the battery by using a wireless charger or another device that functions as a wireless charger.

Caution

Precautions for wireless charging

•  Do not place the charging box on the wireless charger when conductive materials, such as metal objects and magnets, are placed between the charging box and the wireless charger.
•  Keep the charging box away from high temperatures and water sources. The box may get warm during charging. This is normal.

Charging the battery with a wireless charger.

• Place the earpieces in the charging box
• Close the charging box cover
•  Place the charging box on the center of the wireless charger
•  When fully charged, remove the charging box from the wireless charger

Tip

A full charge takes 4 hours by wireless charging.

How to wear

Select suitable ear tips for optimum fit A tight, secure fit will provide the best sound quality and noise cancellation.

1. Test which ear tip provides you with the best sound and wearing comfort.
2. 3 sizes provided – large, medium, and small.

Insert the earpieces

1. Check left or right orientation of the earpieces.
2. Insert the earpieces into the ears and twist slightly until a secure fit is achieved.

Pair the earpieces with your Bluetooth device for the first time

1. Make sure that the earpieces are fully charged and powered off.
2. Open the top cover from charging box.

• The LEDs on both earpieces flash white and blue alternately
• The earpieces are now in pairing mode and are ready to pair with a Bluetooth device (e.g. a mobile phone)

3. Turn on the Bluetooth function of your Bluetooth device.
4. Pair the earpieces with your Bluetooth device. Refer to the user manual of your Bluetooth device.

Note
After powering on, if the earpieces cannot find any previously connected Bluetooth device, it will automatically switch to pairing mode.
The following example shows you how to pair the earpieces with your Bluetooth device.

1. Turn on the Bluetooth function of your Bluetooth device, select Philips TAT5506.
2. Enter the earpieces’ password “0000” (4 zeros) if prompted. For those devices featuring Bluetooth 3.0 or higher, there is no need to enter a password.

Single earpiece (Mono mode)
Take either right or left earpiece out from the charging box for Mono use. The earpiece will power on automatically. You will hear a voice from the earpieces saying “Power on”.

Note
Take the second earpiece from the charging box and they will pair with each other automatically.

Pair the earpieces with another Bluetooth device
If you want to pair another Bluetooth device with the earpieces, make sure the Bluetooth function in any other previously paired or connected devices is turned off.
Long press the button of charging box for about 3 seconds when earpieces flash in white & blue alternately.

Note
The earpieces store 4 devices in the memory. If you try to pair more than 4 devices, the earliest paired device is replaced by the new one.

Use your earpieces

Connect the earpieces to your Bluetooth device

1. Turn on the Bluetooth function of your Bluetooth device.
2. Open the charging box cover.
   The blue LED flashes
   The earpieces will search the last connected Bluetooth device and reconnect to it automatically. If the last connected device is not available, the earpieces will enter pairing mode

Tip

•  The earpieces cannot connect to more than 1 device at the same time. If you have two paired Bluetooth devices, only turn on the Bluetooth function of the device that you want to connect.If you turn on the Bluetooth function of your Bluetooth
• device after turning on the earpieces, you have to go to the Bluetooth menu of the device and connect the earpieces to the device manually.

Note

• If the earpieces fail to connect to any Bluetooth device within 3 minutes, it will turn off automatically to save the battery life.
• In some Bluetooth devices, connection may not be automatic. In this case, you have to go to the Bluetooth menu of your device and connect the earpieces to the Bluetooth device manually.

Control ANC (Active Noise Cancellation)

Enable ANC
Different ANC mode can be toggled via double tap on the right earpiece.

•  ANC function is auto active when put into the ear
• Touch the MFT twice, it will change to awareness mode
•  Touch the MFT twice again, it will turn the ANC function off

Tip
Removing the earpieces will automatically activate sleep mode. When you put the earpieces back they will return to active mode.

Manage your calls and
music

 Reset the earpieces

If you encounter any pairing or connection issue, you can follow the following procedure to reset your earpieces to factory default settings.

1. On your Bluetooth device, go to the Bluetooth menu and remove Philips TAT5506 from the device list.
2. Turn off the Bluetooth function of your Bluetooth device.
3. Return earpieces to charging box and open the lid.
4. Press button on box twice.
5. Follow steps in “Use your earpieces- connect the earpieces to your Bluetooth device.”
6. Pair the earpieces with your Bluetooth device, select Philips TAT5506.

If there is no response from the earpieces, you can follow the below step to reset the hardware of your earpieces.
Tap and hold multi-function touch for 10 seconds.

 Technical data

• Music play time (ANC on): 7+21 hours
• Music play time (ANC off): 8+24 hours
• Standby time: 55 hours
• Charging time: 2 hours
• Lithium-ion battery 55 mAh on each earpiece, Lithium-ion battery 550 mAh on charging box
• Bluetooth version: 5.2
• Compatible Bluetooth profiles:
  •   HFP (Hands-Free Profile)
  • A2DP (Advanced Audio Distribution Profile)
  •  AVRCP (Audio Video Remote Control Profile)

• Supported audio codecs: SBC, AAC
• Frequency range: 2.402-2.480 GHz
• Transmitter power: < 10 dBm
• Operating range: Up to 10 meters (33 feet)
• Auto power off
• USB-C port for charging
• Low battery warning: available

Note
Specifications are subject to change without notice.

Notice

Declaration of conformity
Hereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of Directive
2014/53/EU. You can find the Declaration of Conformity on www.p4c.philips.com.

Disposal of your old product and battery

Your product is designed and manufactured with high quality materials and components which can be recycled and reused.

This symbol on a product means that the product is covered by European Directive 2012/19/EU.
This symbol means that the product contains a built-in rechargeable battery covered by European Directive
2013/56/EU which cannot be disposed of with normal household waste. We strongly advise you to take your product to an official collection point or a Philips service centre to have a professional remove the rechargeable battery. Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health.

Remove the integrated battery

If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing of the earpieces.

• Make sure the earpieces are disconnected from the charging box before removing the battery.
• Make sure the charging box is disconnected from the USB charging cable before removing the battery.

Compliance with EMF
This product complies with all applicable standards and regulations regarding exposure to electromagnetic Fields.

Environmental information
All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.)
Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.

Notice of compliance
The device complies with the FCC rules, Part 15. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC rules
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment ff and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help

Trademarks

Bluetooth
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners.

Siri
Siri is a trademark of Apple Inc., registered in the U.S. and other countries.

Google
Google and Google Play are trademarks of Google LLC.

Frequently asked questions

My Bluetooth earpieces do not turn on. The battery level is low. Charge the earpieces.
I cannot pair my Bluetooth earpieces with my Bluetooth device.
The Bluetooth is disabled. Enable the Bluetooth feature on your Bluetooth device and turn on the Bluetooth device before you turn on the earpieces.
Pairing does not work.

• Put both earpieces into charging box.
• Make sure you have disabled the Bluetooth function of any previously connected Bluetooth devices.
• On your Bluetooth device, delete“Philips TAT5506” from the Bluetooth list.
• Pair your earpieces (see ‘Pair the earpieces with your Bluetooth device for the first time’ on page 6).

The Bluetooth device cannot find the earpieces.

• The earpieces may be connected to a previously paired device. Turn off the connected device or move it out of range.
• Pairing may have been reset or the earpieces have been previously paired with another device. Pair the earpieces with the Bluetooth device again as described in the user manual. (see ‘Pair the earpieces with your Bluetooth device for the first time’ on page 6).

My Bluetooth earpieces are connected to a Bluetooth stereo-enabled mobile phone, but music only plays on the mobile phone speaker.
Refer to the user manual of your mobile phone. Select to listen to music through the earpieces.
The audio quality is poor and a crackling noise can be heard.

• The Bluetooth device is out of range. Reduce the distance between your earpieces and Bluetooth device, or remove obstacles between them.
• Charge your earpieces.

The audio quality is poor when stream-ing from a mobile phone, is very slow or streaming does not work at all.
Make sure your mobile phone not only supports (mono) HFP but also supports A2DP and is BT4.0x (or higher) compati-ble (see ‘Technical data’ on page 11).
The right and left earpieces are discon-nected from each other.

• Put both earpieces into charging box, keep the cover open.
• Short press 3 times casing button.

2021 © MMD Hong Kong Holding Limited. All rights reserved. Specifications are subject to change without notice. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its affiliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product. All other company and product names may be trademarks of its respective companies with which they are associated.
UM_TAT5506_00_EN_V1.0