Bosch DHI623GSG Telescopic Cooker Hood Instructions

BOSCH DHI623GSG Telescopic Cooker Hood

Important safety information

Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location. This appliance is intended for domestic use and the household environment only. The appliance is not intended for use outside. Do not leave the appliance unattended during operation. The manufacturer is not liable for damage that is caused by improper use or incorrect operation. This appliance is intended for use up to a maximum height of 2000 meters above sea level. This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capabilities or by persons with a lack of experience or knowledge if they are supervised or are instructed by a person responsible for their safety how to use the appliance safely and have understood the associated hazards. Children must not play with, on, or around the appliance. Children must not clean the appliance or carry out general maintenance unless they are at least 15 years old and are being supervised. Keep children below the age of 8 years old at a safe distance from the appliance and power cable. Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport. This appliance is not intended for operation with an external clock timer or remote control. Only a licensed professional may connect appliances without plugs. Damage caused by incorrect connection is not covered under warranty.
The danger of suffocation!
Packaging material is dangerous to children. Never allow children to play with packaging material.
The danger of death!
Risk of poisoning from flue gases that are drawn back in. Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as the room air-dependent heat-producing appliance is being operated. Room air-dependent heat-producing appliances (e.g. gas, oil, wood or cooperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air through an exhaust gas system (e.g. a chimney). In combination with an activated vapor extractor hood, room air is extracted from the kitchen and neighboring rooms – a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked
back into the living space.

  • Adequate incoming air must therefore always be ensured.
  • An incoming/exhaust air wall box alone will not ensure compliance with the limit. Safe operation is possible only when the partial vacuum in the place where the heat-producing appliance is installed does not exceed 4 Pa (0.04 bar). This can be achieved when the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/ exhaust air wall boxes, or by other technical means. In any case, consult your responsible Master Chimney Sweep. He is able to assess the house’s entire ventilation setup and will suggest suitable ventilation measures to you. Unrestricted operation is possible if the vapor extractor hood is operated exclusively in the circulating-air mode.

Risk of fire!

  • Hot oil and fat can ignite very quickly. Never leave hot fat or oil unattended. Never use water to put out burning oil or fat. Switch off the hotplate. Extinguish flames carefully using a lid, fire blanket, or something similar.
  • Grease deposits in the grease filter may catch fire. Clean the grease filter at least every 2 months. Never operate the appliance without the grease filter.
  • Grease deposits in the grease filter may catch fire. Never work with naked flames close to the appliance (e.g. flambéing). Do not install the appliance near a heat-producing appliance for solid fuel (e.g. wood or coal) unless a closed, nonremovable cover is available. There must be no flying sparks.
  • When gas burners are in operation without any cookware placed on them, they can build up a lot of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Only operate the gas burners with cookware on them.
  • Operating several gas burners at the same time gives rise to a great deal of heat. A ventilation appliance installed above the cooker may become damaged or catch fire. Never operate two gas burners simultaneously on the highest flame for longer than 15 minutes. One large burner of more than 5 kW (wok) is equivalent to the power of two gas burners.
    Risk of burns!
  • The accessible parts become very hot when in operation. Never touch hot parts. Keep children at a safe distance.
    Risk of injury! 
  • Components inside the appliance may have sharp edges. Wear protective gloves.
  • Items placed on the appliance may fall down. Do not place any objects on the appliance.
  • The light emitted by LED lights is very dazzling and can damage the eyes (risk group 1). Do not look directly into the switched-on LED lights for longer than 100 seconds
    Risk of electric shock!
  • A defective appliance may cause electric shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.
  • Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.
  • Do not use any high-pressure cleaners or steam cleaners, which can result in an electric shock.

Causes of damage

Caution!
Risk of damage due to corrosion. Always switch on the appliance while cooking to avoid condensation. Condensate can produce corrosion damage. Always replace faulty bulbs to prevent the remaining bulbs from overloading. Risk of damage due to ingress of humidity into the electronic circuitry. Never clean operator controls with a wet cloth. Surface damage due to incorrect cleaning. Clean stainless steel surfaces in the direction of the grain only. Do not use any stainless steel cleaners for operator controls. Surface damage due to strong or abrasive cleaning agents. Never use strong and abrasive cleaning agents. Risk of damage from returning condensate. Install the exhaust duct in such a way that it falls away from the appliance slightly (1° slope).

Environmental protection

Your new appliance is particularly energy-efficient. Here you can find tips on how to save even more energy when using the appliance, and how to dispose of your appliance properly.
Saving energy 

  • During cooking, ensure that there is a sufficient supply of air to enable the extractor hood to work efficiently and with a low level of operating noise.
  • Adjust the fan speed to the amount of steam produced during cooking. Only use intensive mode when required. The lower the fan speed, the less energy is consumed.
  • If cooking produces large amounts of steam, select a higher fan speed in good time. If the cooking steam has already spread around the kitchen, the extractor hood will need to be operated for longer.
  • Switch off the extractor hood if you no longer require it.
  • Switch off the lighting if you no longer require it.
  • Clean and (if required) replace the filter at regular intervals in order to increase the effectiveness of the ventilation system and to prevent the risk of fire.
  • Put the lid on to reduce cooking steam and condensation.

Environmentally-friendly disposal
Dispose of packaging in an environmentally-friendly manner. This appliance is labeled in accordance with European Directive 2012/19/EU concerning used electrical and electronic appliances (waste electrical and electronic equipment – WEEE). The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU.

Operating modes

This appliance can be used in exhaust-air mode or circulating-air mode.
Exhaust air mode
The air which is drawn in is cleaned by the grease filters and conveyed to the exterior by a pipe system.
Note: The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft that is used to ventilate installation rooms that contain heat-producing appliances.

  • Before conveying the exhaust air into a non-functioning smoke or exhaust gas flue, obtain the consent of the heating engineer responsible.
  • If the exhaust air is conveyed through the outer wall, a telescopic wall box should be used.

Circulating-air mode
The air which is drawn in is cleaned by the grease filters and an activated carbon filter and conveyed back into the kitchen.

Note: To bind odors in circulating-air mode, you must install an activated carbon filter. The different options for operating the appliance in circulating-air mode can be found in the brochure. Alternatively, ask your dealer. The required accessories are available from specialist outlets, from customer service or from the Online Shop. The accessory numbers can be found at the end of the instructions for use.

Operating the appliance

These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance.
Note: Switch on the extractor hood when you start cooking and switch it off again several minutes after you have finished cooking. This is the most effective way of removing kitchen fumes.

Control panel

Explanation

Filter drawer

Pulling out the filter drawer
Hold the filter drawer by the middle and pull it out. The control panel is accessible and the appliance is ready for operation.
Note: Start the appliance with the functions which were set when the drawer was closed.
Pushing the filter drawer in
Hold the filter drawer by the middle and push it in.
Note: The ventilation is switched off when the drawer is closed, and the light stays on.

Setting the fan

Note: Always adjust the fan strength to meet current conditions. If there is a large build-up of steam or fumes, select a high fan setting.
Switching on
Press the 1, 2, or 3 buttons.
Switching off
Press the 1 button.
Lighting
The lighting can be switched on and off independently of the ventilation.
Press the button.

Cleaning and maintenance

Risk of burns!
The appliance will become hot during operation, especially near the bulbs. Allow the appliance to cool down before cleaning.
Risk of electric shock!
Penetrating moisture may result in an electric shock. Clean the appliance using a damp cloth only. Before cleaning, pull out the main plug or switch off the circuit breaker in the fuse box.
Risk of electric shock!
Do not use any high-pressure cleaners or steam cleaners, which can result in an electric shock.
Risk of injury!
Components inside the appliance may have sharp edges. Wear protective gloves.
Cleaning agents
To ensure that the different surfaces are not damaged by using the wrong cleaning agent, observe the information in the table. Do not use any of the following:

  • Harsh or abrasive cleaning agents,
  • Cleaning agents with high alcohol content,
  • Hard scouring pads or cleaning sponges,
  • High-pressure cleaners or steam cleaners.

Wash new sponge cloths thoroughly before use. Follow all instructions and warnings included with the cleaning agents.

Cleaning the metal mesh grease filters
These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance.
Risk of fire!
Grease deposits in the grease filter may catch fire. Clean the grease filter at least every 2 months. Never operate the appliance without the grease filter.
Notes

  • Do not use any aggressive, acidic, or alkaline cleaning agents.
  • When cleaning the metal mesh grease filters, also clean the holder for the metal mesh grease filters in the appliance using a damp cloth.
  • The metal mesh grease filters can be cleaned in the dishwasher or by hand.

By hand:
Note: You can use a special grease solvent for stubborn dirt. It can be ordered via the Online Shop.

  • Soak the metal mesh grease filters in a hot soapy solution.
  • Clean the filters with a brush and then rinse them thoroughly.
  • Leave the metal mesh grease filters to drain.
    In the dishwasher:
    Note: If the metal mesh grease filters are cleaned in the dishwasher, slight discoloration may occur. This has no effect on the function of the metal mesh grease filters.
  • Do not clean heavily soiled metal mesh grease filters together with utensils.
  • Place the metal mesh grease filters loosely in the dishwasher. The metal mesh grease filters must not be wedged in.

Removing metal grease filter

  1. Open the lock and swing down the metal grease filter. When you do this, take hold of the metal grease filter from underneath with your other hand.
  2. Take the metal grease filter out of the holder.
    Note: Fat may accumulate in the bottom of the metal grease filter. Hold the metal grease filter level to prevent fat from dripping out.
  3. Clean the metal grease filters.
  4. After removing the filters, clean the inside of the appliance

Installing the metal mesh grease filter

  1. Insert the metal mesh grease filter. While doing this, place the other hand under the metal mesh grease filter.
  2. Fold the metal mesh grease filter upwards, locking it in place. Changing the activated charcoal filter (only in circulating-air mode) In order to guarantee efficient odor filtration, the filter must be serviced regularly. The activated charcoal filters must be replaced at least every 4 months.

Notes

  • The activated charcoal filters are not included in the delivery. The activated charcoal filters can be obtained from specialist retailers, from our after-sales service or from the Online Shop.
  • The activated charcoal filters cannot be cleaned or reactivated.
  1. For removing the metal grease filter, see above.
  2. Withdraw the old activated charcoal filters from the holder.
  3. Press the new activated charcoal filters onto the holder until they can be heard to lock in place.
  4. For fitting the metal grease filter, see above

Troubleshooting

Malfunctions often have simple explanations. Please read the following notes before calling the after-sales service.
Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians. If the appliance is defective, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service.

Fault table

Replacing the LED lights

Risk of electric shock!
When changing the bulbs, the bulb socket contacts are live. Before changing the bulb, unplug the appliance from the mains or switch off the circuit breaker in the fuse box.
Risk of injury!
The light emitted by LED lights is very dazzling and can damage the eyes (risk group 1). Do not look directly into the switched-on LED lights for longer than 100 seconds.
Important! Only use bulbs of the same type and wattage.

  1. Disconnect the appliance from the power supply.
  2. Remove the metal grease filter.
  3. Unscrew the bulb and replace it with a bulb of the same type.
  4. Fit the metal grease filters.
  5. Plug in the mains plug and switch the circuit breaker back on.

After-sales service

Our after-sales service is there for you if your appliance needs to be repaired. We will always find the right solution in order to avoid unnecessary visits from a service technician. When calling us, please give the product number (E no.) and the production number (FD no.) so that we can provide you with the correct advice. The rating plate with these numbers can be found inside the appliance (remove the metal mesh grease filter to gain access). You can make a note of the numbers of your appliance and the telephone number of the after-sales service in the space below to save time should it be required. Please be aware that a visit by an after-sales engineer will be charged if a problem turns out to be the result of operator error, even during the warranty period. Please find the contact data of all countries in the enclosed customer service list.
To book an engineer visit and product advice
0344 892 8979 Calls are charged at local or mobile rate. Rely on the professionalism of the manufacturer. You can therefore be sure that the repair is carried out by trained service technicians who carry original spare parts for your appliances.

Accessories for circulating-air mode

Activated charcoal filter