Haier QAS740 Electric Compact Ranges User Manual

Haier QAS740 Electric Compact Ranges

SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

WARNING: Read all safety instructions before using the product. Failure to follow these instructions may result in fire, electrical shock, serious injury or death.

ANTI-TIP DEVICE

WARNING: 

•  A child or adult can tip the range and be killed.
•  Verify the anti-tip bracket has been properly installed and engaged.
•  Ensure the anti-tip bracket is re-engaged when the range is moved.
• Do not operate the range without the anti-tip bracket in place and engaged.
•  Failure to do so can result in death or serious burns to children or adults

To reduce the risk of tipping the range, the range must be secured by a properly installed anti-tip bracket. See installation instructions shipped with the bracket for complete details before attempting to install.
For Free-Standing Ranges

To check if the bracket is installed, ensure there is no cookware on top of the range and all surfaces are cool to the touch. Carefully slide out the range from the wall approximately three inches. Look behind the range to see if there is a metal bracket attached to the floor or the wall. To check if the bracket is installed correctly on the wall. To check if the bracket is installed correctly, grasp the back of the range, being careful not to grab or bend the rear trim piece. Tilt the range forward slightly and confirm the anti-tip bracket engages the back of the range, limiting the forward tip of the range. If the
anti-tip bracket does not engage the range and prevent it from tipping, verify the anti-tip bracket has been properly installed. If this does not solve the problem or the anti-tip bracket is not present, call 800.626.8774 in the US or 800.561.3344 in Canada. If the range is pulled from the wall for any reason, always repeat this procedure to verify the range is properly secured by the anti-tip bracket.
Never completely remove the leveling legs or the range will not be secured to the anti-tip device properly.

`

WARNING:
GENERAL SAFETY INSTRUCTIONS

•  Use this appliance only for its intended purpose as described in this Owner’s Manual.
•  FIRE HAZARD: Never leave the range unattended with the cooktop ON above a Lo setting. Keep flammable items away from the cooktop. Turn off all controls when done cooking. Failure to follow these instructions can result in fire, serious injury, or death.
•  Be sure your appliance is properly installed and grounded by a qualified installer in accordance with the provided installation instructions.
•  Do not attempt to repair or replace any part of your range unless it is specifically recommended in this manual. All other servicing should be transferred to a qualified technician.
•  Before performing any service, unplug the range or disconnect the power supply at the household distribution panel by removing the fuse or switching off the circuit breaker.
• Do not leave children alone—children should not be left alone or unattended in an area where an appliance is in use. They should never be allowed to climb, sit or stand on any part of the appliance.
• CAUTION: Do not store items of interest to children above a range or on the backyard of a range—children climbing on the range to reach items could be seriously injured.
• Use only dry potholders—moist or damp potholders on hot surfaces may result in burns from steam. Do not let potholders touch hot surface units or heating elements. Do not use a towel or other bulky cloth in place of potholders.
•  Never use your appliance for warming or heating the room.
•  Do not touch the surface units, the heating elements, or the interior surface of the oven. These surfaces may be hot enough to burn even though they are dark in color. During and after use, do not touch, or let clothing or other flammable materials contact the surface units, areas nearby the surface units or any interior area of the oven; allow sufficient time for cooling first. Other surfaces of the appliance may become hot enough to cause burns. Potentially hot surfaces include the cooktop, areas facing the cooktop, oven vent opening, surfaces near the opening and crevices around the oven door.
•  Do not heat unopened food containers. Pressure could build up and the container could burst, causing an injury.
• Do not use any type of foil or liner to cover the oven bottom or anywhere in the oven, except as described in this manual. Oven liners can trap heat or melt, resulting in damage to the product and risk of shock, smoke, or fire. Avoid scratching or impacting glass doors, cooktops, or control panels. Doing so may lead to glass breakage. Do not cook on a product with broken glass. Shock, fire or cuts may occur.
• Cook food thoroughly to help protect against foodborne illness. Minimum safe food temperature recommendations can be found at IsItDoneYet.gov and fsis.usda.gov. Use a food thermometer to take food temperatures and check several locations.

WARNING

KEEP FLAMMABLE MATERIALS AWAY FROM THE OVEN
Failure to do so may result in fire or personal injury.

•  Do not store or use flammable materials in an oven or near the cooktop, including paper, plastic, pot holders, linens, wall coverings, curtains, drapes, and gasoline or other flammable vapors and liquids.
• Never wear loose-fitting or hanging garments while using the appliance. These garments may ignite if they contact hot surfaces causing severe burns
•  Do not let cooking grease or other flammable materials accumulate in or near the range. Grease in the oven or on the cooktop may ignite.
•  Clean ventilating hoods frequently. Grease should not be allowed to accumulate on the hood or filter.

WARNING
IN THE EVENT OF A FIRE, TAKE THE FOLLOWING STEPS TO PREVENT INJURY AND FIRE SPREADING

• Do not use water on grease fires. Never pick up a flaming pan. Turn the controls off. Smother a flaming pan on a surface unit by covering the pan completely with a well-fitting lid, cookie sheet or flat tray. Use a multi-purpose dry chemical or foam-type fire extinguisher.
•  If there is a fire in the oven during baking, smother the fire by closing the oven door and turning the oven off or by using a multi-purpose dry chemical or foam-type fire extinguisher.
• If there is a fire in the oven during self-clean, turn the oven off and wait for the fire to go out. Do not force the door open. Introduction of fresh air at self-clean temperatures may lead to a burst of flame from the oven, Failure to follow this instruction may result in severe burns.

WARNING
COOKTOP SAFETY INSTRUCTIONS

•  Never leave the surface units unattended with the cooktop ON above a Lo setting. Boilovers cause smoking and greasy spillovers that may catch on fire.
•  Always be present at the range when cooking with oil or grease. Surface cooking is an “attended” activity.
•  Never leave oil unattended while frying. If allowed to heat beyond its smoking point, the oil may ignite resulting in a fire that may spread to surrounding cabinets. Use a deep-fat thermometer whenever possible to monitor oil temperature.
•  To avoid oil spillover and fire, use a minimum amount of oil when shallow pan-frying and avoid cooking frozen foods with excessive amounts of ice.
•  Use proper pan size—Select cookware having flat bottoms large enough to cover the surface heating element. The use of undersized cookware will expose a portion of the surface unit to direct contact and may result in the ignition of clothing. Proper relationship of cookware to the surface units will also improve efficiency.
•  Only certain types of glass, glass/ceramic, earthenware or other glazed containers are suitable for cooktop service; others may break because of the sudden change in temperature.
•  To minimize the possibility of burns, ignition of flammable materials and spillage, the handle of a container should be turned toward the center of the range without extending over nearby surface units.
•  When preparing flaming foods under a hood, turn the fan on.
•  If power is lost to an electric cooktop while a surface unit is ON, the surface unit will turn back on as soon as power is restored. In the event of power loss, failure to turn
  all surface unit knobs to the OFF position may result in the ignition of items on or near the cooktop, leading to serious injury or death.

WARNING:
RADIANT COOKTOP SAFETY INSTRUCTIONS

• • Use care when touching the cooktop. The glass surface of the cooktop will retain heat after the controls have been turned off.
• Do not cook on a broken cooktop. If the glass cooktop should break, cleaning solutions and spillovers may penetrate the broken cooktop and create a risk of electric shock. Contact a qualified technician immediately.
•  Avoid scratching the glass cooktop. The cooktop can be scratched with items such as knives, sharp instruments, rings or other jewelry, and rivets on clothing.
•  Do not place or store items that can melt or catch fire on the glass cooktop, even when it is not being used. If the cooktop is inadvertently turned on, it may ignite. Heat from the cooktop or oven vent after it is turned off may cause them to ignite also.
• • Use CERAMA BRYTE® ceramic Cooktop Cleaner and CERAMA BRYTE® Cleaning Pad to clean the cooktop. Wait until the cooktop cools and the indicator light goes out before cleaning. A wet sponge or cloth on a hot surface can cause steam burns. Some cleaners can produce noxious fumes if applied to a hot surface. NOTE: Sugar spills are an exception. They should be scraped off while still hot using an oven mitt and a scraper. See the Cleaning the glass cooktop section for detailed instructions.
• Read and follow all instructions and warnings on the cleaning cream label.

WARNING:
OVEN SAFETY INSTRUCTIONS

• Stand away from the range when opening the oven door. Hot air or steam which escapes can cause burns to hands, face and/or eyes.
• Do not use the oven if a heating element develops a glowing spot during use or shows other signs of damage. A glowing spot indicates the heating element may fail and present a potential burn, fire, or shock hazard. Turn the oven off immediately and have the heating element replaced by a qualified service technician.
•  Keep the oven vent unobstructed.
•  Keep the oven free from grease buildup. Grease in the oven may ignite.
•  Place oven racks in the desired location while the oven is cool. If rack must be moved while the oven is hot, do not let the potholder contact the hot heating element in the oven.
•  When using cooking or roasting bags in the oven, follow the manufacturer’s directions.
•  Pull the oven rack to the stop-lock position when loading and unloading food from the oven. This helps prevent burns from touching hot surfaces of the door and oven walls.
•  Do not leave items such as paper, cooking utensils or food in the oven when not in use. Items stored in an oven can ignite.
•  Never place cooking utensils, pizza or baking stones, or any type of foil or liner on the oven floor. These items can trap heat or melt, resulting in damage to the product and risk of shock, smoke or fire.

PROPER DISPOSAL OF YOUR APPLIANCE
Dispose of or recycle your appliance in accordance with Federal and Local Regulations. Contact your local authorities for the environmentally safe disposal or recycling of your appliance.

USING THE RANGE USING THE RANGE

SURFACE UNITS

WARNING:
FIRE HAZARD:

•  Never leave the range unattended with the cooktop ON above a Lo setting. Keep flammable items away from the cooktop. Turn off all controls when done cooking. Failure to follow these instructions can result in fire, serious injury or death. Throughout this manual, features and appearance may vary from your model.
  How to Set
• Push the knob in and turn in either direction to the setting you want.
• A surface ON indicator light will glow when any surface unit is on.
• For glass cooktop surfaces:
• A HOT COOKTOP indicator light will:
• come on when the unit is hot to the touch.
•  stay on even after the unit is turned off.
•  stay on until the unit is cooled to approximately 150°F.
  

At both OFF and HI the control clicks into position. You may hear slight clicking sounds during cooking, indicating the control is maintaining your desired setting.
Be sure you turn the control knob to OFF when you finish cooking.
Coil Cooktops
Each coil surface unit uses “SENSI-TEMP TECHNOLOGY” to reduce the risk of cooktop oil and grease fires. This feature is located in the center of each surface unit. Power to the surface unit is temporarily interrupted when a pot or pan exceeds expected cooking temperatures. Even after the surface units are turned off, the surface unit retains enough heat to continue cooking. To avoid overcooking, remove pans from the surface units when the food is cooked. Avoid placing anything on the surface unit until it has cooled completely.

• Cookware for Coil Cooktops
  The following information will help you choose cookware that will give good performance on coil cooktops.
• NOTE: Follow all cookware manufacturer’s recommendations when using any type of cookware on the coil cooktop.
  Recommended
• Stainless Steel
  Thin unclad stainless steel will give poor performance.
• Aluminum
  Heavyweight recommended.
• Good conductivity. Because of its low melting point, thin-weight aluminum should not be used.
• Copper Bottom
• Enamel (painted) on Cast Iron
• Cast Iron
• Avoid/Not Recommended
  Enamel (painted) on Steel
• Glass-ceramic
  Poor performance.
• Stoneware
  Poor performance.

SURFACE UNITS (Cont.)
Radiant Glass Cooktop

• The radiant cooktop features heating units beneath a smooth glass surface.
• NOTE: A slight odor is normal when a new cooktop is used for the first time. It is caused by the heating of new parts and insulating materials and will disappear in a short time.
• NOTE: On models with light-colored glass cooktops, it is normal for the cooking zones to change color when hot or cooling down. This is temporary and will disappear as the glass cools to room temperature.
• The surface unit will cycle on and off to maintain your selected control setting.
• It is safe to place hot cookware on the glass surface even when the cooktop is cool.
• Even after the surface units are turned off, the glass cooktop retains enough heat to continue cooking. To avoid overcooking, remove pans from the surface units when the food is cooked. Avoid placing anything on the surface unit until it has cooled completely.
• Water stains (mineral deposits) are removable using the cleaning cream or full-strength white vinegar.
• The use of window cleaner may leave an iridescent film on the cooktop. The cleaning cream will remove this film.
•  Don’t store heavy items above the cooktop. If they drop onto the cooktop, they can cause damage.
•  Do not use the surface as a cutting board.

Do not slide cookware across the cooktop because it can scratch the glass—the glass is scratch-resistant, not scratch proof.

Temperature Limiter on Radiant Glass Cooktops

• Every radiant surface unit has a temperature limiter.
• The temperature limiter protects the glass cooktop from getting too hot.
• The temperature limiter may cycle the surface units off for a time if:
  • the pan boils dry.
  • the pan bottom is not flat.
  • the pan is off-center.
  • there is no pan on the unit.

SURFACE UNITS (Cont.)

• Cookware for Radiant Glass Cooktops
  The following information will help you choose cookware that will give good performance on glass cooktops.
• NOTE: Follow all cookware manufacturer’s recommendations when using any type of cookware on the ceramic cooktop.
• Recommended
  Stainless Steel
  Aluminum
• Heavyweight recommended.
• Good conductivity. Aluminum residues sometimes appear as scratches on the cooktop but can be removed if cleaned immediately. Because of its low melting point, thin weight aluminum should not be used.
  Copper Bottom
  Copper may leave residues that can appear as scratches. The residues can be removed, as long as the cooktop is cleaned immediately. However, do not let these pots boil dry. Overheated metal can bond to glass cooktops. An overheated copper bottom pot will leave a residue that will permanently stain the cooktop if not removed immediately.
  Enamel (painted) on Cast Iron
  Recommended if the bottom of the pan is coated.
• Avoid/Not Recommended
  Enamel (painted) on Steel
  Heating empty pans can cause permanent damage to cooktop glass. The enamel can melt and bond to the ceramic cooktop.
  Glass-ceramic
• Poor performance. Will scratch the surface.
  Stoneware
• Poor performance. May scratch the surface.
  Cast Iron
• Not recommended—unless designed specifically for glass cooktops.
  Poor conductivity and slow to absorb heat. Will scratch the cooktop surface.

More about Cookware

• Place only dry pans on the surface elements. Do not place lids on the surface elements, particularly wet lids. Wet pans and lids may stick to a smooth surface when cool.
•  Do not use woks that have support rings. This type of work will not heat on the cooktop.
• We recommend that you use only a flat-bottomed wok. They are available at your local retail store. The bottom of the wok should have the same diameter as the surface element to ensure proper contact.
• Some special cooking procedures require specific cookware such as pressure cookers or deep-fat fryers. All cookware must have flat bottoms and be the correct size.

SURFACE UNITS (Cont.)

Home Canning Tips
Be sure the canner is centered over the surface unit. Make sure the canner is flat on the bottom. To prevent burns from steam or heat, use caution when canning. Use recipes and procedures from reputable sources. These are available from manufacturers such as Ball® and Kerr® and the Department of Agriculture Extension Service. Flat-bottomed canners are recommended. Use of water bath canners with rippled bottoms may extend the time required to bring the water to a boil.
OVEN CONTROLS
Oven Mode Selector Knob
Turn the Oven Mode Selector knob to the mode you want. Your oven has the following cooking modes: Bake Broil and Convection Bake. See Cooking Modes section and Steam Clean for more information.

•  Bake
•  Broil
•  Convection Bake
•  Steam Clean

Oven Temperature Knob

• Turn the Oven Temp knob to the setting you want until Oven/Cycle light turns off.
• The Oven/Cycle light comes on when the burner is on. It will cycle on and off during cooking.
• To Adjust the Thermostat:
• Pull the Oven Temp knob off the range and look at the backside. To make an adjustment, loosen  (approximately one turn), but do not completely remove, the two screws on the back of the knob.
• With the back of the knob facing you, hold the outer edge of the knob with one hand and turn the front of the knob with the other hand.
• To increase the oven temperature, move the top screw toward the right. You’ll hear a click for each notch you move the knob.
• To decrease the oven temperature, move the top screw toward the left.
• Each click will change the oven temperature to approximately 10°F. (Range is plus or minus 30°F from the arrow.) We suggest that you make the adjustment one click from the original setting and check oven performance before making any additional adjustments.
• After the adjustment is made, retighten screws so they are snug, but be careful not to overtighten.
•  Replace the knob, match the flat area of the knob to the shaft, and check the performance

OVEN CONTROLS (Cont.)
Timer/Clock Display

• Timer/Clock: Works as a countdown timer and a clock. To set the countdown timer, press the Timer/Clock pad and use the + and – pads to set the time in hours and minutes. After seeing the time, press the Timer/Clock pad again and the “:” will stop blinking indicating the timer has started. To cancel the timer, press the Timer/Clock pad to ensure the “:” is blinking. Then change the time to 0:00 and press the Timer/Clock pad changing it back to the clock time. To set the clock, press and hold the Timer/Clock pad for several seconds and use the + and – pads to set the clock. After changing the time, hit the Timer/Clock pad to finalize the clock time.
• Oven Light: Turns the oven light on or off.
•  Pad: Use to decrease time for the countdown timer and clock. Short taps to this pad will decrease the time by small amounts. Holding the pad down will decrease the time by large amounts.
• Pad: Use to increase time for the countdown timer and clock. Short taps to this pad will increase the time by small amounts. Holding the pad down will increase the time by large amounts.
•  Lock Out: Locks out the timer and clock display so that pressing any of the pads will be disabled. Press and hold the Lock Out pad for three seconds to lock or unlock the display.
• SABBATH MODE
  Certain models comply with the Star-K Jewish Sabbath requirements for use during the Sabbath and holidays. For the latest list of models, see star-k.org.
• Start Baking
  To start baking, simply turn the thermostat knob to the desired temperature. Because a thermostat model will respond with a clicking sound when the thermostat knob is used to turn on the oven, this operation should take place before the Sabbath or Holidays begin.
• Adjusting the Temperature
  To adjust the oven temperature while in compliance with Sabbath requirements, the user must observe the oven ON indicator light:”
  • To adjust the oven temperature to a higher value, the user must first confirm the “OVEN ON” light is on. Only then, can the user turn the knob to a higher temperature than was previously set.
  • To adjust the oven temperature to a lower value, the user must first confirm the “OVEN ON” light is off. Only then, can the user turn the knob to a lower temperature than was previously set.
• Stop Baking
  To stop baking, simply turn the thermostat knob to the off position. Because a thermostat model will respond with a clicking sound when the thermostat knob is used to turn off the oven, this operation should take place after the Sabbath or Holidays end.
• Oven Light Operation
  The oven light can be set to either on or off prior to the start of the Sabbath or the holiday. Opening and closing of the door will not change the state of the oven light.
• Sabbath Mode Power Outage Note
  If a power outage occurs during a Sabbath bake, the unit will return to Sabbath bake mode when power is restored and the oven will return to the same temperature as before the outage, without any intervention from the user.

COOKWARE GUIDELINES
The material, finish, and size of cookware affect baking performance. Dark, coated, and dull pans absorb heat more readily than light, shiny pans. Pans that absorb heat more readily can result in a browner, crisper and thicker crust. If using dark and coated cookware check food earlier than the minimum cook time. If undesirable results are obtained with this type of cookware consider reducing oven temperature by 25º F next time.

• Shiny pans can produce more evenly cooked baked goods such as cakes and cookies.
•  Glass and ceramic pans heat slowly but retain heat well. These types of pans work well for dishes such as pies and custards.
•  Air-insulated pans heat slowly and can reduce bottom browning.
•  Keep cookware clean to promote even heating.

CARE AND CLEANING

OVEN
Be sure all controls are off and all surfaces are cool before cleaning any part of the oven.

Oven Interior
The interior of your new oven can be cleaned manually or by using the Steam Clean feature.
Spillage of marinades, fruit juices, tomato sauces, and basting liquids containing acids may cause discoloration and should be wiped up as soon as hot surfaces cool, then clean and rinse.

Manual Cleaning
Do not use oven cleaners, strong liquid cleaners, steel wool, or scouring pads on the interior of the oven. For soils on the oven bottom and other enameled surfaces, use a gentle abrasive containing oxalic acid, such as Bar Keepers Friend®, with a non-scratch sponge. Take care not to apply any abrasive cleaners or sponges to the door glass, as it will scratch the reflective coating. The oven interior and door glass may be cleaned using a soft cloth with mild soap and water, or vinegar and water solution. After cleaning, rinse with clean water and dry with a soft cloth.

Steam Clean
The Steam Clean feature is for cleaning light soil from your oven.
To use the Steam Clean feature:

•  Start with the oven at room temperature.
•  Wipe excess grease and soil from the oven.
•  Pour 1/2 cup of water onto the bottom of the oven.
•  Close the door.
•  Turn both your Oven Mode Knob and Oven Temperature Knob to Steam Clean Setting.

Do not open the door during the Steam Cleaning cycle. At the end of the Steam Clean cycle, soak up the remaining water, and wipe the moisture-softened soil from the oven walls and door.
Oven Exterior
Do not use oven cleaners, abrasive cleansers, strong liquid cleaners, steel wool, plastic scouring pads or cleaning powders on the interior or exterior of the oven. Clean with mild soap and water or a 50/50 solution of vinegar and water. Rinse with clean water and dry with a soft cloth. When cleaning surfaces, make sure that they are at room temperature and not in direct sunlight.
Spillage of marinades, fruit juices, tomato sauces, and basting liquids containing acids may cause discoloration and should be wiped up as soon as hot surfaces cool, then clean and rinse.

Oven Racks
All oven racks may be cleaned by hand with an abrasive cleaner or steel wool. After cleaning the racks, use a soft cloth or paper towel to rub a small amount of vegetable oil on the left and right edges of the rack. This will ensure the racks are easy to slide in and out of the oven.

COOKTOP

Control Panel and Knobs
Wipe the control panel after each use of the oven with a damp cloth. For cleaning, use mild soap and water or a 50/50 solution of vinegar and water. Rinse with clean water. Polish dry with a soft cloth.
Do not use abrasive cleansers, strong liquid cleaners, plastic scouring pads or oven cleaners on the control panel—they will damage the finish. Stainless Steel Surfaces (on some models) Do not use a steel wool pad; it will scratch the surface. To clean the stainless steel surface, use warm sudsy water or a stainless steel cleaner or polish. Always wipe the surface in the direction of the grain. Follow the cleaner instructions for cleaning the stainless steel surface. Cleaners with oxalic acid such as Bar Keepers Friend Soft Cleanser™ will remove surface rust, tarnish and small blemishes.

Use only a liquid cleanser free of grit and rub in the direction of the brush lines with a damp, soft sponge. To inquire about purchasing cleaning products including stainless steel appliance cleaner or polish, see the Accessories and Consumer Support sections at the end of this manual. For easier cleaning, the control knobs may be removed by pulling them directly outwards once the knobs are in the OFF position. Do not pull knobs up or down or hang objects on them. This can damage the gas valve shaft. When removing the tri-ring (on some models) and the dual-oval (on some models) burner knobs, remember their location. While all other knobs are interchangeable, these knobs must be placed in the same location after cleaning. See the Surface Burner section for a detailed view of these knobs. The knobs can be washed by hand with soap and water or in a dishwasher. To replace knobs after cleaning, align the hole on the knob backside with the gas valve shaft and push inward until the knob is securely fastened. All knobs are interchangeable.

Cooktop Surface
Do not use oven cleaners, abrasive cleansers, strong liquid cleaners, steel wool, plastic scouring pads, or cleaning powders on the cooktop surface. Clean with mild soap and water or a 50/50 solution of vinegar and water. Rinse with clean water and dry with a soft cloth. When cleaning surfaces, make sure that they are at room temperature and not in direct sunlight. Spillage of marinades, fruit juices, tomato sauces, and basting liquids containing acids may cause discoloration and should be wiped up as soon as hot surfaces cool, then clean and rinse. If your model has a stainless steel cooktop surface, refer to the Stainless Steel Surface cleaning instructions featured in the Control Panel and Knobs section.

GLASS COOKTOP
Normal Daily Use Cleaning
ONLY use Ceramic Cooktop Cleaner on the glass cooktop. Other creams may not be as effective.
To maintain and protect the surface of your glass cooktop, follow these steps:

•  Before using the cooktop for the first time, clean it with ceramic cooktop cleaner. This helps protect the top and makes cleanup easier.
•  Before using the cooktop for the first time, clean it with ceramic cooktop cleaner. This helps protect the top and makes cleanup easier.
•  Shake the cleaning cream well. Apply a few drops of ceramic cooktop cleaner directly to the cooktop.
•  Use a paper towel or non-scratch cleaning pad ceramic cooktops to clean the entire cooktop surface.
•  Use a dry cloth or paper towel to remove all cleaning residue. No need to rinse.

NOTE: it is very important that you do not heat the cooktop until it has been cleaned thoroughly.

Burned-On Residue

NOTE: DAMAGE to your glass surface may occur if you use scrub pads other than those recommended.

•  Allow the cooktop to cool.
• Spread a few drops of ceramic cooktop cleaner on the entire burned residue area.
• Using a cleaning pad for ceramic cooktops, rub the residue area, applying pressure as needed.
• If any residue remains, repeat the steps listed above as needed.
•  For additional protection,  after all residue has been removed, polish the entire surface with ceramic cooktop cleaner and a paper towel.

Heavy, Burned-On Residue

•  Allow the cooktop to cool.
  Use a single-edge razor blade scraper at approximately a 45° angle against the glass surface and scrape the soil. It will be necessary to apply pressure to the razor scraper in order to remove the residue.
•  After scraping with the razor scraper, spread a few drops of ceramic cooktop cleaner on the entire burned residue area. Use a non-scratch cleaning pad to remove any remaining residue.
•  For additional protection, after all residue has been removed, polish the entire surface with ceramic cooktop cleaner and a paper towel.

The ceramic cooktop scraper and all recommended supplies
are available through our Parts Center. See the Accessories and Consumer Support sections at the end of this manual.
NOTE: Do not use a dull or nicked blade.
Metal Marks and Scratches

• Be careful not to slide pots and pans across your cooktop.  It will leave metal markings on the cooktop surface. These marks are removable using the ceramic cooktop cleaner with a non-scratch cleaning pad for ceramic cooktops.
•  If pots with a thin overlay of aluminum or copper are allowed to boil dry, the overlay may leave black discoloration on the cooktop. This should be removed immediately before heating again or the discoloration may be permanent.
• NOTE: Carefully check the bottom of pans for roughness that would scratch the cooktop.
• Be careful not to place aluminum baking sheets or aluminum frozen entrée containers on a hot cooktop surface. It will leave shinny dots or markings on the cooktop surface. These markings are permanent and cannot be cleaned off.

GLASS COOKTOP (Cont.)
Damage from Sugary Spills and Melted Plastic
Special care should be taken when removing hot substances to avoid permanent damage of the glass surface. Sugary spillovers (such as jellies, fudge, candy, syrups) or melted plastics can cause pitting of the surface of your cooktop (not covered by the warranty) unless the spill is removed while still hot. Special care should be taken when removing hot substances. Be sure to use a new, sharp razor scraper. Do not use a dull or nicked blade.

•  Turn off all surface units. Remove hot pans.
•  Wearing an oven mitt:
  a. Use a single-edge razor blade scraper (CERAMA BRYTE® Ceramic Cooktop Scraper) to move the spill to a cool area on the cooktop.
  b. Remove the spill with paper towels.
•  Any remaining spillover should be left until the surface of the cooktop has cooled.
•  Don’t use the surface units again until all of the residues has been completely removed.

• Do not allow excess water to run into any holes or slots in the door.
• Wipe dish soap over any baked-on spatters on the glass. Use a single-sided safety razor blade to clean it off. Then wipe over the glass with a soapy cloth to remove any residue and dry off.
• The area outside the gasket can be cleaned with a soap-filled plastic scouring pad. Do not rub or clean the door gasket – it has an extremely low resistance to abrasion.
• If you notice the gasket becoming worn, frayed, or damaged in any way or if it has become displaced on the door, you should have it replaced. Cleaning the Door Exterior
• If a stain on the door vent trim is persistent, use a mild abrasive cleaner and a sponge scrubber for best results. Do not use this method on any other surface.

Stainless Steel Surfaces (on some models)
Do not use a steel wool pad; it will scratch the surface. To clean the stainless steel surface, use warm sudsy water or a stainless steel cleaner or polish. Always wipe the surface in the direction of the grain. Follow the cleaner instructions for cleaning the stainless steel surface. To inquire about purchasing cleaning products including stainless steel appliance cleaner or polish, see the Accessories and Consumer Support sections at the end of this manual.

Removable Storage Drawer
The storage drawer is a good place to store cookware and bakeware. Do not store plastics or flammable material in the drawer. The storage drawer may be removed for cleaning under the range. Clean the storage drawer with a damp cloth or sponge. Never use harsh abrasives or scouring pads. Your storage drawer may have plastic slides (shown to the right) or metal rails. Follow the respective removal and replacement instructions for your model’s configuration. Removing the Storage Drawer

•  Pull drawer straight out until it stops.
• Continue to pull the drawer until it is detached from the oven.
• Replacing the Storage Drawer
  Rest the left drawer rail around the inner left rail guide and slide it in slightly.
  Place the right drawer rail around the inner right rail guide and slide it in slightly.
  Slide the drawer all the way in.

OVEN LIGHT

WARNING:
SHOCK OR BURN HAZARD:

Before replacing the oven light bulb, disconnect the electrical power to the range at the main fuse or circuit breaker panel. Failure to do so may result in electric shock or burn.

CAUTION:

BURN HAZARD: The glass cover and bulb should be removed when cool. Touching hot glass with bare hands or a damp cloth can cause burns.
Oven Light Replacement
Be sure to let the light cover and bulb cool completely.

To remove the cover:

• Hold a hand under the cover so it doesn’t fall when released. With fingers of the same hand, firmly push back the wire cover holder. Lift off the cover. Do not remove any screws to remove the cover.
•  Replace bulb with a 40-watt appliance bulb.
• To replace the cover:
• Place it into the groove of the light receptacle. Pull wire forward to the center of the cover until it snaps into place.
•  Connect electrical power to the range.

OVEN DOOR
The door is very heavy. Be careful when removing and lifting the door. Do not lift the door by the handle.
To Remove the Door:

•  Fully open the door.
•  Pull the hinge locks up and away from the range frame to the unlocked position.
•  Firmly grasp both sides of the door near the top.
•  Close the door until the top of the door is approximately 6” from the range frame.
•  Lift the door up and away from the range until both hinge arms are clear of the slots in the range frame.

To Replace the Door:

•  Firmly grasp both sides of the door near the top.
•  With the door at the same angle as the removal position, rest the notch on the underside of the left hinge arm on the bottom edge of the left hinge slot. The notch in the hinge arm must be fully seated at the bottom of the slot. Repeat for the right side.
•  Fully open the door. If the door will not fully open, the notches in the bottoms of the hinge arms have not seated correctly in the bottom edge of the slot. Lift the door off the range and repeat the previous step.
•  Push the hinge locks toward the range cavity and down to the locked position.
•  Close the oven door.

TROUBLESHOOTING TIPS

Save time and money! Review the charts on the following pages first and you may not need to call for service.

TROUBLESHOOTING TIPS

LIMITED WARRANTY

Haierappliances.com
All warranty service is provided by our Factory Service Centers, or an authorized Customer Care® technician. To schedule service online, visit us at Haierappliances.com, or call Haier at 1-877-337-3639. Please have your serial number and your model number available when calling for service.
Servicing your appliance may require the use of the onboard data port for diagnostics. This gives a Haier factory service technician the ability to quickly diagnose any issues with your appliance and helps Haier improve its products by providing Haier with information on your appliance. If you do not want your appliance data to be sent to Haier, please advise your technician not to submit the data to Haier at the time of service.

What Haier will not cover:

• Service trips to your home to teach you how to use the  product
•  Improper installation, delivery, or maintenance.
•  Failure of the product if it is abused, misused, modified, or used for other than the intended purpose or used commercially.
•  Replacement of house fuses or resetting of circuit breakers.
•  Damage to the product caused by accident, fire, floods, or acts of God.
•  Damage to finish, such as surface rust, tarnish, or small blemishes not reported within 48 hours of delivery.
•  Incidental or consequential damage caused by possible defects with this appliance.
•  Damage caused after delivery.
•  Product not accessible to provide required service.
•  Service to repair or replace light bulbs, except for LED lamps.
•  Effective January 1, 2022, cosmetic damage to the glass cooktop such as, but not limited to, chips, scratches, or baked-on residue not reported within 90 days of installation.
•  Effective January 1, 2022, damage to the glass cooktop due to impact or misuse. See example.

EXCL