Miele ESW 7010 14cm High Gourmet Warming Drawer without Handle Installation Guide
Miele ESW 7010 14cm High Gourmet Warming Drawer without Handle
Installation
Safety instructions for installation
Incorrect installation can cause damage to the drawer and/or the combination appliance. The appliance must only be installed by a suitably qualified and competent person.
- The socket and on-off switch should be easily accessible after the drawer has been installed.
- The drawer may only be installed in combination with those appliances quoted by Miele as being suitable. If the drawer is used in combination with other appliances, the warranty will be invalidated, as trouble-free operation cannot be guaranteed.
- The base on which the drawer and the combination appliance are fitted must be fixed in place and must support the weight of both appliances.
- When building in the combination appliance, it is essential to follow the instructions given in the operating and installation instructions supplied with it.
- The warming drawer must be installed in such a way that:
- The contents of the dishes can be seen when it is opened. This is to avoid scalding from hot food spilling over.
- There is enough space for the drawer to be pulled out fully.
Installation notes
The drawer can be used in combination with the following Miele built-in appliances:
- all ovens with an appliance front width of 595 mm
- all steam ovens with an appliance front width of 595 mm
- all coffee machines with an appliance front width of 595 mm
- all microwaves with an appliance front width of 595 mm
- the Dialog oven with an appliance front width of 595 mm
The combination appliance is placed on top of the drawer without the need for an interim shelf. The drawer is available in 3 models, which differ in height. The building-in dimensions for the drawer must be added to the building-in dimensions for the combination appliance to establish the niche size required.
Installation dimensions ESW 7010, ESW 7110
All dimensions in this instruction booklet are given in mm.
Combination appliance for niches with a height of 450 mm
The furniture housing unit must not have a back panel fitted behind the building-in niche.
Combination appliance for niches with a height of 590 mm
The furniture housing unit must not have a back panel fitted behind the building-in niche.
Side view
- A ESW 70×0: 22 mm
- ESW 71×0: 23.3 mm
Connections and ventilation
- Front view
- Mains connection cable,
- = 2,000 mm
- No connections permitted in this area
- Ventilation cut-out, min. 18000 mm2
Installation dimensions ESW 7020, ESW 7120
All dimensions in this instruction booklet are given in mm.
Combination appliance for niches with a height of 450 mm
The furniture housing unit must not have a back panel fitted behind the building-in niche.
Combination appliance for niches with a height of 590 mm
The furniture housing unit must not have a back panel fitted behind the building-in niche.
SIDE VIEW
- A ESW 70×0: 22 mm
- ESW 71×0: 23.3 mm
Connections and ventilation
- Front view
- Mains connection cable,
- = 2,000 mm
- No connections permitted in this area
- Ventilation cut-out, min. 18000 mm2
Installation dimensions ESW 7030
All dimensions in this instruction booklet are given in mm.
Combination appliance for niches with a height of 450 mm
The furniture housing unit must not have a back panel fitted behind the building-in niche.
Combination appliance for niches with a height of 590 mm
The furniture housing unit must not have a back panel fitted behind the building-in niche.
- A ESW 7030: 22 mm
Connections and ventilation
- Front view
- Mains connection cable
- = 2,000 mm
- No connections permitted in this area
- Ventilation cut-out, min. 18000 mm2
Check that the base on which the drawer will sit is clean and level (use a spirit level). This is important for the appliance to function correctly.
- Push the drawer into the housing unit until the drawer front is flush with the housing unit and make sure that it is correctly aligned in the unit.
- Open the drawer and use the 2 screws supplied to secure it to the side walls of the furniture unit.
- Build in the combination appliance in accordance with the operating and installation instructions supplied with it.
Electrical connection
We recommend that you connect the drawer to the mains electricity via a suitable switched electrical socket. This simplifies servicing. The socket and on-off switch should be easily accessible after the drawer has been installed.
Danger of injury due to unauthorised installation, maintenance and repairs. Danger of injury! Miele cannot be held liable for unauthorised installation, maintenance and repair work as this can be dangerous to users.
Miele cannot be held liable for damage or injury (e.g. electric shock) caused by the lack of or inadequacy of an on-site earthing system. If the plug is removed from the connection cable or if the cable is supplied without a plug, the drawer must be connected to the electricity supply by a suitably qualified and competent electrician. If the socket is no longer accessible, or if a hard-wired connection is planned, an additional means of disconnection must be provided for all poles. Suitable means of disconnection include switches with an all-pole contact gap of at least
3 mm. These include miniature circuit breakers, fuses and relays. The connection data is given on the data plate. Please ensure this information matches the household mains electricity supply. After installation, ensure that all electrical components are shielded and cannot be accessed by users.
Total power output
See data plate.
Connection data
The connection data is given on the data plate. Please ensure this information matches the household mains supply.
Residual current device
For extra safety, it is advisable to install a residual current device (RCD) with a trip range of 30 mA. Do not connect the appliance via an extension lead.
Replacing the mains connection cable
If replacing the mains connection cable, it must be replaced with a cable type H 05 VV-F, available from Miele, by a suitably qualified and competent electrician.