VIKING VK660 Super Pixel Blade Stage Lighting User Manual
VIKING VK660 Super Pixel Blade Stage Lighting
Statement
The product has well capability and intact packing when leave factory. All of the user should comply with warning item and manual, any misuse cause of the damages are not included in our guarantee, and also can not be responsible for any malfunction & problem owing to ignore the manual.
Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. ˜ Unpack and check carefully there is no transportation damage before using the unit.
- Before operating, ensure that the voltage and frequency of power supply match the power requirements of the unit.
- It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
- The unit is for indoor use only. Use only in a dry location.
- The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces. Be sure that no ventilation slots are blocked.
- Disconnect main power before replacement or servicing.
- Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
- Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always by taking its base.
- Maximum ambient temperature is Ta: 40. DO NOT operate it where the temperature is higher than this Unit surface temperature may reach up to 85. DO NOT touch the housing bare-hand during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before replacing or serving.
- The event of serious operating problem, stop using the unit immediately.Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.
Technical Specifications
- Light Sources: 6*60W 4IN1 osram RGBW LED
- Beam Angle: 4.5°- 55°
- Power Consumption: 450w
- Power Voltage: AC 100-260V, 50/60Hz
- Net Weight: 16 kgs
Control
- DMX Channel: 25/45 Channels
- Control Modes: DMX512/mater-Slave/Auto Run/Music
Pan/Tilt
- Pan/Tiit: Infinite Rotation
- Pan/Tilt Resolution: 8/16 bit
Construction
- Display: 180° reversible LCD Display
- Data In/Out socket: 3-pin & 5-pin XLR sockets
- Power Socket: Powercon in
- Protection Rating: IP20
Features
- Dimmer: 0~100% smooth dimming ;two dimmer model in optional( delay or without delay)
- Led single controlled
- Strong beam effects with high brightness
- Led temperature protection & Fan run speed automatic based on the head temperature.
LUX Date
- Min Zoom range =3°
- Max Zoom range =45
Display & Menu
Display:
MENU To select the programming functions
DOWN To go backward in the selected functions
UP To go forward in the selected functions
ENTER To confirm the selected functions
Set DMX Address Code
- Press “Menu” to “Set DMX Address”,and press”ENTER” keys to enter into
- Show “Set DMX Address DMX Address:001”,Press the “UP and DOWN” keys to amended
- Press “ENTER”keys to save and Exit,Press the”MENU”Keys does not save and Exit.
Menu |
Pan Degree | 540 degree | 360 degree |
Mic Sense | 001 – 100,Sound sensitivity adjustment | ||
Language | English | Chinese | |
Reset | Yes | No | |
Default | Yes | No | |
Adjust |
Pass Word:up+down+up+down | ||
Pan | 0 – 255 | ||
Tilt | 0 – 255 | ||
Focus | 0 – 255 | ||
Red | 0 – 255 | ||
Green | 0 – 255 | ||
Blue | 0 – 255 | ||
White | 0 – 255 | ||
Address | Setting from 001 – 512 | ||
1.Yes |
Reverse |
Forward or reversed setting |
Pan | 2.No | ||
Tilt |
1.Yes | ||||
2.No | |||||
Display |
1.Yes | ||||
2.No | |||||
Channel |
45 channels | 45 channel mode | |||
25 channels | 25 channel mode | ||||
Inform |
1.CH Value | Each channel value | |||
2.Temp c | Temperature of led board | ||||
3.Soft V1.2 | Show the version number | ||||
Mode |
DMX 512 | ||||
AUTO | |||||
SOUND | |||||
Manual |
Master |
Pan:0–255 |
Manual control | ||
Tilt:0–255 | |||||
Focus:0–255 | |||||
Red:0–255 | |||||
Alone |
Greed:0–255 | ||||
Blue:0–255 | |||||
White:0–255 | |||||
Strobe:0-255 |
DMX Channel List
Model 1 – CH45
Channel | Display | Function | Value |
CH-1 | Pan adjustment | Pan adjustment | 0 — 255 |
CH-2 | Pan adjustment | Pan adjustment | 0 — 255 |
CH-3 | Tilt adjustment | Tilt adjustment | 0 — 255 |
CH-4 | Tilt adjustment | Tilt adjustment | 0 — 255 |
CH-5 | Pan/Til speed | from fast to slow | 0 — 255 |
CH-6 |
Pan infinite rotation |
No | 0 — 55 |
Clockwise from slow to fast | 56 — 155 | ||
Anticlockwise from slow to fast | 156—255 | ||
CH-7 |
Tilt infinite rotation |
No | 0 — 55 |
Clockwise from slow to fast | 56 — 155 | ||
Anticlockwise from slow to fast | 156—255 | ||
CH-8 |
Strobe |
No | 0 — 15 |
from slow to fast | 16 — 214 |
Random stroboscopic | 215—255 | ||
CH-9 | Dimming | From dark to bright | 0 — 255 |
CH-10
CH-10 |
Dimming Model
Dimming Model |
Model – 1 | 0 — 49 |
Model – 2 | 50 — 99 | ||
Model – 3 | 100— 149 | ||
Model – 4 | 150— 255 | ||
CH-11 | Focus | from near to far | 0 — 255 |
CH-12 | Red – 1 |
From dark to bright |
0 — 255 |
CH-13 | Green – 1 | ||
CH-14 | Blue – 1 | ||
CH-15 | White – 1 | ||
CH-16 | Red – 2 |
0 — 255 | |
CH-17 | Green – 2 | ||
CH-18 | Blue – 2 | ||
CH-19 | White – 2 | ||
CH-20 | Red – 3 |
0 — 255
0 — 255 | |
CH-21 | Green – 3 | ||
CH-22 | Blue – 3 | ||
CH-23 | White – 3 |
CH-24 | Red – 4 |
From dark to bright |
0 — 255 |
CH-25 | Green – 4 | ||
CH-26 | Blue – 4 | ||
CH-27 | White – 4 | ||
CH-28 | Red – 5 |
0 — 255 | |
CH-29 | Green – 5 | ||
CH-30 | Blue – 5 | ||
CH-31 | White – 5 | ||
CH-32 | Red – 6 |
0 — 255 | |
CH-33 | Green – 6 | ||
CH-34 | Blue – 6 | ||
CH-35 | White – 6 | ||
CH-36 |
Static color |
No | 0—-15 |
R 100%,G up,B0% | 16—-35 | ||
R down,G 100%,B0% | 36—-55 | ||
R 0%,G 100%,B up | 56—-75 | ||
R 0%,G100%,B up | 76—-95 | ||
R up,G0%,B100% | 96—-115 | ||
R 100%,G0%,B down | 116—-135 |
CH-36 |
Static color |
R 100%,G up,B up | 136—-155 |
R100%,G down,B100% | 156—-175 | ||
R100%,G 100%,B100%,W100% | 176—-195 | ||
2800K | 196—-200 | ||
3200K | 201—-205 | ||
3500K | 206—-210 | ||
4000K | 211—-215 | ||
4500K | 216—-220 | ||
5000K | 221—-225 | ||
5500K | 226—-230 | ||
6000K | 231—-235 | ||
6500K | 236—-240 | ||
7000K | 241—-245 | ||
7500K | 246—-250 | ||
8000K | 251—-255 | ||
CH-37 |
Effects |
No | 0 —- 9 |
3 numbers 1 effect | 10 — 99 | ||
Jump | 100 — 149 |
gradual change | 150 — 255 | ||
CH-38 |
Zone |
No | |
Static Zone -1 | 0 — 9 | ||
Static Zone -2 | 10 — 19 | ||
Static Zone -3 | 20 — 29 | ||
Static Zone -4 | 30 — 39 | ||
Static Zone -5 | 40 — 49 | ||
Static Zone -6 | 50 — 59 | ||
Static Zone -7 | 60 — 69 | ||
Static Zone -8 | 70 — 79 | ||
Static Zone -9 | 80 — 89 | ||
Static Zone -10 | 90 — 99 | ||
Static Zone -11 | 100 — 109 | ||
Static Zone -12 | 110 — 119 | ||
Static Zone -13 | 120 — 129 | ||
Static Zone -14 | 130 — 139 | ||
Static Zone -15 | 140 — 149 | ||
Static Zone -16 | 150 — 159 | ||
Dynamic Zone -1 | 160 — 169 |
CH-38 |
Zone |
Dynamic Zone -2 | 170 — 179 |
Dynamic Zone -3 | 180 — 189 | ||
Dynamic Zone -4 | 190 — 199 | ||
Dynamic Zone -5 | 200 — 209 | ||
Dynamic Zone -6 | 210 — 219 | ||
Dynamic Zone -7 | 220 — 229 | ||
Dynamic Zone -8 | 230 — 255 | ||
CH-39 | Zone change speed | 0 — 255 | |
CH-40 | Zone change fade | 0 — 255 | |
CH-41 | Color of Zone Red |
From dark to bright |
0 — 255 |
CH-42 | Color of Zone Green | ||
CH-43 | Color of Zone Blue | ||
CH-44 | Color of Zone White | ||
CH-45 |
Reset |
No | 0 — 79 |
Reset | 80 — 99 | ||
No | 100 — 255 |
Model 2 – CH25
Channel | Display | Function | Value |
CH-1 | Pan adjustment | Pan adjustment | 0 — 255 |
CH-2 | Pan adjustment | Pan adjustment | 0 — 255 |
CH-3 | Tilt adjustment | Tilt adjustment | 0 — 255 |
CH-4 | Tilt adjustment | Tilt adjustment | 0 — 255 |
CH-5 | Pan/Til speed | from fast to slow | 0 — 255 |
CH-6
CH-6 |
Pan infinite rotation
Pan infinite rotation |
No | 0 — 55 |
Clockwise from slow to fast | 56 — 155 | ||
Anticlockwise from slow to fast | 156—255 | ||
No | 0 — 55 |
CH-7 |
Tilt infinite rotation |
Clockwise from slow to fast | 56 — 155 |
Anticlockwise from slow to fast | 156—255 | ||
CH-8 |
Strobe |
No | 0 — 15 |
from slow to fast | 16 — 214 | ||
Random stroboscopic | 215—255 | ||
CH-9 | Dimming | From dark to bright | 0 — 255 |
CH-10
CH-10 |
Dimming Model
Dimming Model |
Model – 1 | 0 — 49 |
Model – 2 | 50 — 99 | ||
Model – 3 | 100— 149 | ||
Model – 4 | 150— 255 | ||
CH-11 | Focus | from near to far | 0 — 255 |
CH-12 | Red – 1 | ||
CH-13 | Green – 1 |
CH-14 | Blue – 1 | From dark to bright | 0 — 255 |
CH-15 | White – 1 | ||
CH-16 |
Static color |
No | 0—-15 |
R 100%,G up,B0% | 16—-35 | ||
R down,G 100%,B0% | 36—-55 | ||
R 0%,G 100%,B up | 56—-75 | ||
R 0%,G100%,B up | 76—-95 | ||
R up,G0%,B100% | 96—-115 | ||
R 100%,G0%,B down | 116—-135 | ||
R 100%,G up,B up | 136—-155 | ||
R100%,G down,B100% | 156—-175 | ||
R100%,G 100%,B100%,W100% | 176—-195 | ||
2800K | 196—-200 | ||
3200K | 201—-205 |
CH-16 |
Static color |
3500K | 206—-210 |
4000K | 211—-215 | ||
4500K | 216—-220 | ||
5000K | 221—-225 | ||
5500K | 226—-230 | ||
6000K | 231—-235 | ||
6500K | 236—-240 | ||
7000K | 241—-245 | ||
7500K | 246—-250 | ||
8000K | 251—-255 | ||
CH-17 |
Effects |
No | 0 —- 9 |
3 numbers 1 effect | 10 — 99 | ||
Jump | 100 — 149 | ||
gradual change | 150 — 255 |
CH-18 |
Zone |
No | |
Static Zone -1 | 0 — 19 | ||
Static Zone -2 | 20 — 29 | ||
Static Zone -3 | 30 — 39 | ||
Static Zone -4 | 40 — 49 | ||
Static Zone -5 | 50 — 59 | ||
Static Zone -6 | 60 — 69 | ||
Static Zone -7 | 70 — 79 | ||
Static Zone -8 | 80 — 89 | ||
Static Zone -9 | 90 — 99 | ||
Static Zone -10 | 100 — 109 | ||
Static Zone -11 | 110 — 119 | ||
Static Zone -12 | 200 — 255 | ||
CH-19 | Zone change speed | 0 — 255 |
CH-20 | Zone change fade | 0 — 255 | |
CH-21 | Color of Zone Red |
From dark to bright |
0 — 255 |
CH-22 | Color of Zone Green | ||
CH-23 | Color of Zone Blue | ||
CH-24 | Color of Zone White | ||
CH-25 |
Reset |
No | 0 — 79 |
Reset | 80 — 99 | ||
No | 100 — 255 |
Shape
DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
- DO NOT open the unit within five minutes after switching off.
- The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
There are no user-serviceable parts inside the unit. DO NOT open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact your nearest dealer.
Installation:
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture. The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people.
Troubleshooting
Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting:
The unit does not work, no light and the fan does not work
- Check the connection of power and main fuse.
- Measure the mains voltage on the main connector.
- Check the power on LED.
Not responding to DMX controller
- DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
- If the DMX LED is on and no response to the channel, check the address settings and DMX polarity.
- If you have intermittent DMX signal problems, check the pins on connectors or on PCB of the unit or the previous one.
- Try to use another DMX controller.
- Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit.
One of the channels is not working well
- The stepper motor might be damaged or the cable connected to the PCB is broken.
- The motor’s drive IC on the PCB might be out of condition