Honeywell HWB11AC-PRT WiFi and BT Module User Manual

USER MANUAL
HWB11AC-PRT, WIFI & BT Module

MODEL NO: HWB11AC-PRT CORPORATE GRAPHICS AND COMMUNICATIONS
Administrative Style Sheet Guide
802.11a/b/g/n/ac +
BT 5.0 System on Module
Graphic Design Institute 12345 Main Street · Suite 100
Honeywell Confidential and Proprietary
FCC ID: HD5-HWB11
IC: 1693B-HWB11
Model Name: HWB11AC-PRT

Introduction

This document specifies the details for a WiFi 802.11a/b/g/n/ac with a BT5.0 module called Honeywell Part No.

This HWB11AC-PRT module is a Wi-Fi/BT system on the module which will be placed inside the Honeywell products like printers, barcode scanners, RFID readers etc. To enable wireless connectivity. This module includes MAC & a physical layer of 802.11a/b/g/n/ac and the Bluetooth modem.
This module operates on a 5.0V DC Power supply with internal onboard regulation to generate 3.3v for powering ON all the circuits. The entire RF circuit is enclosed in an RF shield of dimension 25mm X 25mm.
The module uses an internal power amplifier and LNA for the 2.4GHz frequency band and an external front end chip for the 5GHz frequency band. All filters and diplexers are included in the module to ensure maximum power flatness and optimum VSWR. The module has one antenna chain for 1X1 output.
The module supports a range of data rates from 1Mbps in 802.11b mode to MCS9 in 802.11ac mode. This chipset also supports the concurrent operation of Bluetooth (Version5.0) for wireless connectivity during browsing or other device applications. Along with both standard and high speed (HS) Bluetooth data rates, Bluetooth low energy modes are also supported. Hardware WAPI acceleration engine, AES, TKIP, WPA and WPA2 are supported to provide the latest security requirement on your network.
The Device communicates with HOST using the SDIO interface for WIFI and UART interface for BLUETOOTH.
HWB11AC-PRT ­ System on Module Features

• IEEE 802.11 a/b/g/n/ac WLAN
• Bluetooth 5.0 + HS
• Bluetooth-WLAN coexistence
• WiFi Wake on Wireless (WoW)
• 20/40 MHz bandwidth at 2.4GHz
• 20/40/80 MHz bandwidth at 5GHz
• Internal PA/LNA
• Module Size: 80 mm x 37 mm x 18mm, (LxWxH) Board
• 802.11d/e/h/i/k/r
• Low Current consumption in IEEE PS and Deep Sleep
• WiFi Security methods: OPEN, WEP, WPA2-PSK, WPA2-1X PEAP-MSCHAPV2, PEAP-TLS, EAP-TTLS)

Block Diagram

HWB11AC-PRT module is designed based on Qualcomm QCA6174A chipset solution. It supports a generic SDIO, UART interface to connect the WLAN/BT to the host processor. A simplified block diagram of the HWB11AC-PRT module is depicted in the above picture.

Technical Specifications

Recommended Operating Condition

Footprint, Front & Back view

Pin Configurations of Module

Wireless Specifications

WLAN
The HWB11AC-PRT module complies with the following features and standards.

BLUETOOTH
The Radio specification is compliant with the Bluetooth 5.0 + EDR specification

WLAN Radio Specifications IEEE Specifications
WiFi TX EVM follows the IEEE spec that as list in the table below:

Wi-Fi 5 GHz Power Table (FCC/IC)
Note: Band 5600 MHz to 5650 MHz is not supported for Canada Wi-Fi 2.4 GHz Power Table (ETSI)

Wi-Fi 5 GHz Power Table (FCC/IC)

Note: Band 5600 MHz to 5650 MHz is not supported for Canada
Wi-Fi 2.4 GHz Power Table (ETSI)

Wi-Fi 5 GHz Power Table (ETSI)

BT & BLE 2.4GHz (ETSI & FCC/IC)
BLE 2.4GHz

1Mbps, 2Mbps & 3Mbps

The HWB11AC-PRT module 2.4GHz Wi-Fi Sensitivity is list in the table below:

The HWB11AC-PRT module 5GHz Wi-Fi Sensitivity as listed in the table below:

BLUETOOTH Radio Characteristics

Antenna Type & Specifications

Module to be used with Antenna part no: MAF94367, Make: Laird Technologies
Honeywell part no: 805-833-001

ANTENNA PATTERNS

This radio transmitter [IC:1693B-HWB11] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed above, with the maximum permissiblegain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited from use with this device.
RF Layout & Design Guidelines
RF Layout & Design Guidelines
I. Do not run antenna cables directly above or directly below the radio module.
II. Do not run any high-speed digital lines below the radio.
III. Use proper electro-static-discharge (ESD) procedures when installing the HWB11AC-PRT module.
IV. Use non-conductive labels and to be pasted over the EMI shield provided on the module.
Agency Approvals
FCC:
Model: HWB11AC-PRT
FCC ID: HD5-HWB11
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. However, there is no guarantee that interference will not occur in an installation. If this equipment does cause harmful interference to radio or reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation.
Caution:
MODIFICATION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the device.
INSTALL & OPERATION: The equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
Industry Canada
Model: HWB11AC-PRT
IC: 1693B-HWB11
This device complies with Industry Canada RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note:
Within the 5.15 to 5.25 GHz band, UNII devices will be restricted to indoor operations only.
Labelling Guidelines for Products
The proposed FCC IC label format is to be placed on the module. If it is not visible when the module is installed into the system, “Contains FCC ID: HD5-HWB11, Contains IC:1693B-HWB11” shall be placed on the outside of the final host system.