Asus I005D/I005DC ROG Phone 5 User Guide

ASUS I005D/I005DC ROG Phone 5 User Guide

 

ASUS Phone (Mobile Phone)
Model: ASUS_I005D / ASUS_I005DC (ZS673KS)

Before you start, ensure that you have read all the safety information and operating instructions in this User Guide to prevent injury or damage to your device.

NOTES:

  • For the complete E-Manual and more detailed information, refer to https://www.asus.com/support/.
  • Illustrations are for reference only. Actual product appearance may vary.

 

Front features

 

Side features

 

Rear features

 

NOTES:

  • The USB Type-C port supports USB 2.0 transfer rate. The USB Type-C port on the left side of your ROG Phone supports USB 3.2 Gen 1 transfer rate.
  • Go to Settings > Advanced > Air Triggers to set
    Air Triggers.

 

Aero Active Cooler features

Use the AeroActive Cooler to keep your ROG Phone working at a high frequency during heavy workloads by providing a better thermal solution, and offering the ultimate user experience.

NOTES:

  • Only ASUS_I005D comes with the Aero Active Cooler.
  • Connect your Aero Active Cooler to the Pogo Pin of your ROG Phone.
  • You can use your Aero Active Cooler while using the bundled ROG Phone 5 Case.

To install AeroActive Cooler:

  1. Align the female Pogo Pin on the side of your phone with the male Pogo Pin on the bottom of your AeroActive Cooler and gently push down your phone.
  2. Push your phone backward until you hear a click.

NOTES:

  • It is not recommended that you connect other devices to your ROG Phone when you install the phone on the AeroActive Cooler.
  • Docking your ROG Phone on an accessory with fan(s) will impact the audio quality when making phone calls and recording.

To use the kickstand of AeroActive Cooler:
Open the kickstand on the back of the AeroActive Cooler to get optimal viewing experience.

 

Charging your ROG Phone

To charge your ROG Phone:

  1. Connect the USB connector into the power adapter’s USB port.
  2. Connect the other end of the USB Type-C cable to your ROG Phone.
  3. Plug the power adapter into a wall socket.

NOTES:

  • We recommend that you charge your ROG phone through one USB Type-C port at a time.
  • Only the USB Type-C port on the left side of your ROG Phone has Display Port functionality.
  • If you connect USB Type-C OTG or charging devices to both of the USB Type-C ports on your ROG Phone, the USB Type-C port on the left side of your ROG Phone will become the master and the charging current or OTG device on the bottom port will be limited.

IMPORTANT!

  • When using your ROG Phone while it is plugged to a power outlet, the grounded power outlet must be near to the unit and easily accessible.
  • When charging your ROG Phone through your computer, ensure that you plug the USB Type-C cable to your computer’s USB port.
  • DO NOT charge your ROG phone underwater or when the USB connector is wet.
  • Avoid charging your ROG Phone in an environment with ambient temperature of above 35 °C (95 °F).

NOTES:

  • For safety purposes, use ONLY the bundled power adapter and cable to avoid damaging your device and prevent the risk of injury.
  • For safety purposes, use ONLY the bundled power adapter and cable to charge your ROG Phone.
  • The input voltage range between the wall outlet and this adapter is AC 100V – 240V. The output voltage of the AC power adapter for this device is +5V-20V 3A, 60W.

 

Installing a Nano SIM card

To install a Nano SIM card:

  1. Push a pin into the hole on the Nano SIM card tray to eject it. Insert the Nano SIM card(s) into the card slot(s).

2. Push the tray to close it.

NOTES:

  • Both Nano SIM card slots support GSM/GPRS/EDGE, WCDMA/HSPA+/DC-HSPA+, FDD-LTE, TD-LTE, and 5G NR Sub-6 network bands. Both Nano SIM cards can connect to VoLTE (4G Calling) service. But only one can connect to 5G NR Sub-6 data service at a time.
  • Actual network and frequency band usage depends on network deployment in your area. Contact your telecom carrier if 5G NR Sub-6 support and VoLTE (4G Calling) service are available in your area.

CAUTION!

  • Do not use sharp tools or solvent on your device to avoid scratches on it.
  • Use only a standard Nano SIM card on your ROG Phone.

 

Using NFC

NOTE: NFC is only available in selected regions/countries.

You can use NFC in the following two scenarios:

Reader mode: Your phone reads information from a contact less card, NFC tag, or other NFC devices.

Place the NFC area of your phone on the contact less card, NFC tag, or NFC device.

Card Emulation mode: Your phone can be used like a contact less card.
Place the NFC area of your phone on the NFC area of the NFC reader.

 

Federal Communications Commission Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

The antenna(s) used for this transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

The country code selection is for non-US models only and is not available to all US models. Per FCC regulation, all WiFi products that are marketed in US must be fixed to US-operated channels only.

The responsible party within the USA per 47 CFR Part 2.1077(a)(3):

ASUS COMPUTER INTERNATIONAL (America)
Address: 48720 Kato Rd., Fremont, CA 94538, USA
Telephone: +1-510-739-3777

 

RF Exposure Information (SAR)

This device has been tested and meets applicable limits for Radio Frequency (RF) exposure.
Specific Absorption Rate (SAR) refers to the rate at which the body absorbs RF energy. SAR limits are 1.6 Watts per kilogram (over a volume containing a mass of 1 gram of tissue) in countries that follow the United States FCC limit and 2.0 W/kg (averaged over 10 grams of tissue) in countries that follow the Council of the European Union limit. Tests for SAR are conducted using standard operating positions with the device transmitting at its highest certified power level in all tested frequency bands.

To reduce exposure to RF energy, use a hands-free accessory or other similar option to keep this device away from your head and body. Carry this device at least 15 mm away from your body to ensure exposure levels remain at or below the as-tested levels. Choose the belt clips, holsters, or other similar body-worn accessories which do not contain metallic components to support operation in this manner. Cases with metal parts may change the RF performance of the device, including its compliance with RF exposure guidelines, in a manner that has not been tested or certified, and use such accessories should be avoided.

The highest FCC SAR values for the device (ASUS_I005D/ASUS_I005DC) are as follows:

  • 1.17 W/Kg @1g(Head)
  • 1.19 W/Kg @1g(Body)

The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: MSQI005D.

 

FCC Statement (HAC)

This phone has been tested and rated for use with hearing aids for some of the wireless technologies that it uses. However, there may be some newer wireless technologies used in this phone that have not been tested yet for use with hearing aids. It is important to try the different features of this phone thoroughly and in different locations, using your hearing aid or cochlear implant, to determine if you hear any interfering noise. Consult your service provider or the manufacturer of this phone for information on hearing aid compatibility. If you have questions about return or exchange policies, consult your service provider or phone retailer.

The Federal Communications Commission has implemented rules and a rating system designed to enable people who wear hearing aids to more effectively use these wireless telecommunications devices. The standard for compatibility of digital wireless phones with hearing aids is set forth in American National Standard Institute (ANSI) standard C63.19-2011. There are two sets of ANSI standards with ratings from one to four (four being the best rating): an “M” rating for reduced interference making it easier to hear conversations on the phone when using the hearing aid microphone, and a “T” rating that enables the phone to be used with hearing aids operating in the telecoil mode thus reducing unwanted background noise.

The Hearing Aid Compatibility rating is displayed on the wireless phone box.

A phone is considered Hearing Aid Compatible for acoustic coupling (microphone mode) if it has an “M3” or “M4” rating. A digital wireless phone is considered Hearing Aid Compatible for inductive coupling (telecoil mode) if it has a “T3” or “T4” rating.

The tested M-Rating and T-Rating for this device (ASUS_I005D/ASUS_I005DC) are M3 and T3.

You’ll want to try a number of wireless phones so that you can decide which works the best with your hearing aids. You may also want to talk with your hearing aid professional about the extent to which your hearing aids are immune to interference, if they have wireless phone shielding, and whether your hearing aid has a HAC rating.

 

Canada, Industry Canada (IC) Notices

This device complies with Industry Canada’s licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

This device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device (ASUS_I005D/ASUS_I005DC) has been evaluated for and shown compliant with the IC Specific Absorption Rate (“SAR”) limits when installed in specific host products operated in portable exposure conditions.

Canada’s REL (Radio Equipment List) can be found at the following web address: http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=eng.

Additional Canadian information on RF exposure also can be found at the following web address: http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html.

This equipment should be installed and operated with minimum distance 15 mm between the radiator and your body.

CAN ICES-003(B)/NMB-003(B)
This Class B digital apparatus complies with Canadian ICES-003.

This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter, except tested built-in radios.

The County Code Selection feature is disabled for products that are marketed in the US/ Canada.

The IC ID for this device (ASUS_I005D/ASUS_I005DC) is 3568A-I005D.

Using GPS (Global Positioning System) on your ROG Phone
To use the GPS positioning feature on your ROG Phone:

  • Ensure that your device is connected to the Internet before using Google Map or any GPS-enabled apps.
  • For first-time use of a GPS-enabled app on your device, ensure that you are outdoors to get the best positioning data.
  • When using a GPS-enabled app on your device inside a vehicle, the metallic component of the car window and other electronic devices might affect the GPS performance.

 

Prevention of Hearing Loss

To prevent possible hearing damage, do not listen at high volume levels for long periods.

A pleine puissance

For France, headphones/earphones for this device are compliant with the sound pressure level requirement laid down in the applicable EN 50332-1:2013 and/or EN50332-2:2013 standard required by French Article L.5232-1.

Safety information
CAUTION! Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

ROG Phone care

  • Use your ROG Phone in an environment with ambient temperatures between 0 °C (32 °F) and 35 °C (95 °F).

The battery
WARNING: Disassembling the battery by yourself will void its warranty and may cause serious harm.

Your ROG Phone is equipped with a high performance non-detachable Li-polymer battery. Observe the maintenance guidelines for a longer battery life.

  • Do not remove the non-detachable Li-polymer battery as this will void the warranty.
  • Avoid charging in extremely high or low temperature. The battery performs optimally in an ambient temperature of +5 °C to +35 °C.
  • Do not remove and replace the battery with a non-approved battery.
  • Use only ASUS battery. Using a different battery may cause physical harm/injury and may damage your device.
  • Do not remove and soak the battery in water or any other liquid.
  • Never try to open the battery as it contains substances that might be harmful if swallowed or allowed to come into contact with unprotected skin.
  • Do not remove and short-circuit the battery, as it may overheat and cause a fire. Keep it away from jewelry or metal objects.
  • Do not remove and dispose of the battery in fire. It could explode and release harmful substances into the environment.
  • Do not remove and dispose of the battery with your regular household waste. Take it to a hazardous material collection point.
  • Do not touch the battery terminals.
  • To avoid fire or burns, do not disassemble, bend, crush, or puncture the battery.

NOTES:

  • Risk of explosion if battery is replaced by an incorrect type.
  • Dispose of used battery according to the instructions.

The charger

  • Use only the charger supplied with your ROG Phone.
  • Never pull the charger cord to disconnect it from the power socket. Pull the charger itself.

Caution
Your ROG Phone is a high quality piece of equipment. Before operating, read all instructions and cautionary markings on the AC Adapter.

  • Do not use the ROG Phone in an extreme environment where high temperature or high humidity exists. The ROG Phone performs optimally in an ambient temperature between 0 °C (32 °F) and 35 °C (95 °F).
  • Do not disassemble the ROG Phone or its accessories. If service or repair is required, return the unit to an authorized service center. If the unit is disassembled, a risk of electric shock or fire may result.
  • Do not short-circuit the battery terminals with metal items.

Operator access with a tool
If a TOOL is necessary to gain access to an OPERATOR ACCESS AREA, either all other compartments within that area containing a hazard shall be inaccessible to the OPERATOR by the use of the same TOOL, or such compartments shall be marked to discourage OPERATOR access.

General Usage (typical body-worn) (for Japan)
This device (front & rear side) should be operated under a separation distance of 15 mm from the human body.

* The other four sides are not in close proximity to the human body at the general use as described above.

5GHz band (W52,W53): Indoor use only (Except for the 5.2GHz transmission with High Power Data Communication System Base Station or Relay Station).

Regional notice for Singapore
This ROG Phone complies with IMDA Standards.

Complies with IMDA Standards
DB103778

India E-waste (Management) Rules 2016
This product complies with the “India E-Waste (Management) Rules, 2016” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls (PBBs) and polybrominated diphenyl ethers (PBDEs) in concentrations exceeding 0.1% by weight in homogenous materials and 0.01 % by weight in homogenous materials for cadmium, except for the exemptions listed in Schedule II of the Rule.

ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components as well as the packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for detailed recycling information in different regions.

India BIS – IS 16333 Notice
Language Input : Hindi, English, Tamil
Readability: Assamese, Bangla, Bodo(Boro), Dogri, Gujarati, Hindi, Kannada, Kashmiri, Konkani,

Maithili, Malayalam, Manipuri(Bangla), Manipuri(Meetei Mayek),

Marathi, Nepali, Oriya, Panjabi, Santhali, Sanskrit, Sindhi (Devanagari),
Tamil, Telugu, Urdu and English

Proper disposal

WARNING
Cancer and Reproductive Harmwww.
P65Warnings.ca.gov

NOTE: For more legal and e-labelling information, check on your device from Settings > System > Regulatory labels and Settings > System > About Phone> Legal Information.

TouchSense® Technology licensed from Immersion Corporation and protected under one or more of the U.S. Patents found at the following address

www.immersion.com/patent-marking.html and other patents pending.

ASUS
Address: 1F., No.15, Lide Rd., Beitou Dist., Taipei City 112, Taiwan
Tel: 886228943447
Fax: 886228907698

Declaration
We declare that the IMEI codes for this product, ROG Phone, are unique to each unit and only assigned to this model. The IMEI of each unit is factory set and cannot be altered by the user and that it complies with the relevant IMEI integrity related requirements expressed in the GSM standards.

Should you have any questions or comments regarding this matter, please contact us.

Sincerely yours,
ASUSTeK COMPUTER INC.
Tel: 886228943447
Fax: 886228907698
Support: https://www.asus.com/support/

Copyright © 2021 ASUSTeK COMPUTER INC.
All Rights Reserved.
You acknowledge that all rights of this Manual remain with ASUS. Any and all rights, including without limitation, in the Manual or website, and shall remain the exclusive property of ASUS and/or its licensors. Nothing in this Manual intends to transfer any such rights, or to vest any such rights to you.

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS.

ZenTalk Fans Forum
(http://www.asus.com/zentalk/global_forward.php)

FCC COMPLIANCE INFORMATION

Per FCC Part 2 Section 2.1077

Responsible Party: Asus Computer International

Address: 48720 Kato Rd, Fremont, CA 94538

Phone/Fax No: (510)739-3777/(510)608-4555

hereby declares that the product Product

Name : ROG Phone 5 (ZS673KS)

Model Number : ASUS_I005D, ASUS_I005DC

Compliance statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

 

Read More About This Manual & Download PDF: