LG 15ZT90P Series 15ZT90P-G-AM32G 15.6-Inch Mobile Thin Client with IPS Display Owner’s Manual

SIMPLE OWNER’S MANUAL
NOTEBOOK

For the safe and convenient use of the product, please read this simple owner’s manual before use.

14ZT90P/15ZT90P Series

www.lg.com
Copyright © 2022 LG Electronics Inc. All Rights Reserved

USB Type-C™ and USB-C™ are trademarks of USB Implementers forum. Thunderbolt™ and Thunderbolt™ logo are the trademarks of Intel Corporation in U.S.A. and/or other countries. Microsoft® and Windows® are registered trademarks or trademarks of Microsoft Corporation in the U.S.A. and/or other countries. NVMe™ is a trademark of NVM Express, Inc The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by LG Electronics is under license. Other trademarks and trade names are those of their respective owners.

To obtain the source code that is contained in this product, under GPL, LGPL, MPL, and other open source licenses that have the obligation to disclose source code, and to access all referred license terms, copyright notices and other relevant documents please visit https://opensource.lge.com. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon email request to . This offer is valid to anyone in receipt of this information for a period of three years after our last shipment of this product.

Before Reading the simple owner’s manual

Any malfunction in the built-in solid state drive (SSD) may result in loss of stored data. You must back up all critical user data to an external storage device (USB HDD, memory card, etc.). If you shut the system down before it is completely loaded, the product may not shut down properly. Shut down the system after it is completely loaded. (It takes about one or two minutes to completely load the system and may vary depending on the conditions.)

Precautions related to OS installation

This product is not provided with the operating system. LG Electronics does not provide the operating system (e.g. MS Windows) for this product. You must purchase and install the operating system that is required to operate the product. To purchase a Windows OS, please contact Microsoft. This product only supports installation of Windows 10 IoT Enterprise, and we are not responsible for all the problems that may occur due to installing and using other operating systems.

Product Components

The components shown below are provided when you purchase the product. Check the components before use.

• Some of its components may look different in shape and color from the pictures in certain models.
• When cleaning the product, use a cleaning agent dedicated to the PC. If you use thinner, benzene, alcohol or other similar agent, the product may be damaged or deformed.

1. The AC adapter and power cable may differ depending on your country, but there is no difference in their functionality.

Windows 10 Installation Guide

If you purchase and install Windows 10 IoT Enterprise, you should perform installation according to the following procedure. For details on installation, refer to the user’s guide or the Help menu provided with the Windows OS.

Names of Parts

The actual product may differ in shape and color from the product images included in this simple owner’s manual.

1. Only applies to products with the fingerprint recognition function.

1. Depending on the specifications of the device connected to the USB-CTM port, it acts as a USB or ThunderboltTM port. The USB-CTM port provides a Quick Charging function for devices that support USB PD (Power Delivery).
2. The names of USB versions have changed from USB 3.0 (or USB 3.1 Gen 1) and USB 3.1 (or USB 3.1 Gen 2) to USB 3.2 Gen 1×1 and USB 3.2 Gen 2×1. Devices that are not authorized with USB may not operate normally when connected to the USB port. The transmission speed of a USB port may differ depending on the type of storage device (NVMeTM, SSD, HDD, etc.) in the system and the connected USB device.
3. The 4-pole ear microphone port supports US 4-pole standards, but not the European 4-pole ear microphone. When using ear microphone (or Bluetooth headset), audio input and output are directed to the connected device and the microphone and speaker on PC do not work. The 4-pole ear microphone port does not support external microphone.

Precautions Regarding Battery

This product has a built-in battery pack. After purchasing your PC, be sure to charge the battery pack completely before using it for the first time.

• The battery is a wearable good and thus the battery may not last as long as before after the battery has been used for a long time.
• The internal battery cannot arbitrarily be removed or replaced. Removing it may void the warranty.
• If you need to remove or replace the battery, please visit a designated service center.
• We charge a fee for removing or replacing the battery.

Precautions When Using the Battery

Warning
The battery may explode due to excessive heat, causing fire. For a safe and efficient use of battery, follow the below directions.

• Do not short-circuit the battery.
• Keep the battery out of reach of children.
• A visible swelling of the battery pack indicates a possible danger. When this occurs, contact your local vendor or service center immediately.
• Use only a certified and designated recharger.
• Keep the battery pack away from heat. (Never put it in a microwave.)
• Do not leave inside a car under the summer heat.
• Do not leave or use at a hot and humid place like a sauna.
• Do not use the machine placed on a heating blanket or other heat reserving materials.
• Do not leave the machine turned on inside a closed space.
• Make sure that the battery ports are not touched by any metallic objects like a key, coin, necklace, and watch.
• Use only a lithium secondary battery certified and guaranteed by mobile device manufactures.
• Do not disassemble or modify the battery. Do not compress or pierce the battery.
• Do not apply shock to the battery. For example, do not drop the battery from a high place.
• Keep the room temperature between 23 °F (-5 °C) and 104 °F (40 °C). Do not expose the PC to heat hotter than 104 °F (60 °C).
• Keep the machine dry.
• Do not discard the battery arbitrarily as you are requested to follow the local procedure for discarding the battery.
• Before using this machine, read this guide carefully.

Notes
When the PC is not used for an extended period of time, refer to the following:

• Check the battery charge level on a regular basis and keep it at 50 %. This allows you to extend the battery life.
• If the battery is left fully charged for an extended period of time, the battery capacity and battery running time may be reduced.
• If the battery is left fully discharged for an extended period of time, it may become overdischarged and cannot be charged again.

For more efficient use of the battery, read the following carefully.

• The battery runs low naturally even if it is kept unused.
• To increase battery lifespan, use the battery for a while before charging it rather than keeping the battery completely charged.
• If you don’t use the product for a long time with the battery completely discharged, the battery lifespan may decrease.

The battery capacity may change due to chemical reactions during charge and discharge.

• LG Notebook frequently checks the charge level of its battery based on usage conditions, and then calculates and correctly indicates the actual remaining level of the battery.
• The battery is wearable goods and thus the life span may become shorter with use. The battery running time may also become shorter accordingly.
• When the battery is fully charged, the machine stops recharging. It resumes recharging when the battery charge rate drops below 95 %. This feature secures the safe and efficient use of the battery.
• When the temperature of the battery drops below 50 °F (10 °C), it is charged in a low current to protect the battery cells. In this case, charging time may stretch to up to 32 hours.

If you use the system at a low temperature, refer to the following:

• The battery capacity may be reduced depending on the chemical characteristics of the battery and the system may not be turned on after it freezes or it is turned off.
• If the system freezes or if it is not turned on, connect the AC adapter to the system and charge the battery fully before use.
• If there is any error in the indication of the battery capacity, charge and discharge the battery two or three times at room temperature to return to the normal operation.

LAN Adapter

1. Connect the LAN adapter to the USB-CTM port on the PC. · The USB-CTM port can be used without having to differentiate between the top and bottom surfaces.
2. Connect the network cable (LAN) to the LAN adapter. 3 Check if you can connect to the internet properly.
   

System Reset

When system is in stop or has not been finished properly while installing and using OS, you should reset the system.

1. Remove the adapter and press the power button for approximately 6 seconds to reset the system.
2. Once the system is reset, press the power button again to turn on the computer.
   • Caution: Unsaved data may be lost. Pressing the power button while the PC is in use may cause damage to the hard disk or a system error.
   

Connecting to the Power

The AC adapter is used to power and charge the PC.

• Do not use any other AC adapter than the one that was provided when you purchased this product.
• The power cable and AC adapter may differ depending on your country or region.

1. Connect an end of the cable to the AC adapter and the other end to a power outlet. · The AC adapter can be used from 100 V to 240 V.
2. Connect the AC adapter jack to the PC USB-CTM port.
   • Ensure that the power jack linked to the AC adapter and product is connected firmly.
   

When the AC adapter is connected, the AC adapter lamp turns on.

• If you try to turn on the system that has entered the Hibernates mode or been turned off after a low-battery alarm, the system will not be turned on but the lamp will blink three times. If this is the case, connect the AC adapter and charge the battery sufficiently before using it.

Precautions When Using the AC Adapter
Do not bend the cable for the AC adapter too much.

• Otherwise, the wires inside the cable may break and cause an electric shock or fire.
  

Caution
Do not leave a liquid container on the PC.

• The system may be short-circuited and damaged.

Warning
Please use an AC adapter certified by LG Electronics Inc.

• Uncertified batteries may explode.
• It may cause a problem in battery charging or system operation.

When you use an AC adapter, follow the below directions.

• 140 °F (60 °C) or more high-humidity spaces, for example, inside cars or saunas, should be avoided when you use or store it.
• Do not disassemble or modify the AC adapter.
• Do not twist the AC adapter plug.
• When you connect the AC adapter, do not forcefully push the plug.

Power Supply and Environments

Regulatory Information

FCC Compliance Statement
This equipment has been tested and found to comply within the limits of a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment on and off), the user is encouraged to try to correct the interference by using one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s (or your) authority to operate the equipment. Only peripherals (digital input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this product. Operation with non-certified peripherals is likely to result in interference to radio and TV reception. Only shielded signal cables may be used with this System. Indoor use only
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment and for indoor use only, use outdoors or in other modes not covered by this manual may violate the FCC regulation and violate the user authority to use the product.
Specially, within the 5.15-5.25 GHz band, U-NII device is restricted to indoor operations to reduce any potential for harmful interference to co-channel MSS operations.

FCC/IC Radio Frequency Exposure
The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used.
Whereas high levels of RF can produce health effects (by heating tissue), exposure to low level RF that does not produce heating effects causes no known adverse health effects. Many studies of low level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. This device have been tested and found to comply with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules(<1.6W/kg).

Supplier’s Declaration of Conformity

Trade Name : LG
Responsible Party:
LG Electronics USA, Inc.
111 Sylvan Avenue, North Building
Englewood Cliffs, New Jersey 07632
Email:

CANADA(IC) Notice
Industry Canada Statement (For Canada)
[For having wireless function (WLAN, Bluetooth,)]
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

IC Radiation Exposure Statement
(For Canada)
[For having wireless function (WLAN, Bluetooth,)]
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm (7.8 inches) between the antenna & your body.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

RSS-247 Requirement
(For Canada) [For product having the wireless function using 5 GHz frequency bands]

(i) the device for operation in the band 5150­5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
(iii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate; and
(iv) [for devices operating in the band 5250-5350 MHz having an e.i.r.p. greater than 200 mW] antenna type(s), antenna models(s), and worstcase tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 of RSS-247 shall be clearly indicated.
Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.

SAFETY REGULATION NOTICE

Battery

• Risk of fire or explosion if the battery is replaced by an incorrect type.
• Replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some lithium battery types).
• Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
• Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
• A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
• Do not store or transport at pressures lower than 11.6 kPa and at above 15 000 m altitude.

Information for Environmental Preservation

Information for Environmental Preservation LGE. announced the `LG Declaration for a Cleaner Environment’ in 1994, and this ideal has served as a guiding managerial principle ever since. The Declaration is a foundation that has allowed us to undertake environmentally friendly activities in careful consideration of economic, environmental, and social aspects. We promote activities for environmental preservation, and we specifically develop our products to embrace the concept of environment-friendly. We minimize the hazardous materials contained in our products. For example, there is no cadmium to be found in our product.

Information for recycling
This product may contain parts which could be hazardous to the environment. It is important that this product be recycled after use. LGE. handles all waste product through an environmentally acceptable recycling method. There are several take-back and recycling systems currently in operation worldwide. Many parts will be reused and recycled, while harmful substances and heavy metals are treated by an environmentally friendly method. If you want to find out more information about our recycling program, please contact your local LG vendor or a corporate representative of LG. We set our vision and policies on a cleaner world by selecting the issue of the global environment as a task for corporate improvement. Please visit our website for more information about our `green’ policies. http://www.lg.com/global/sustainability/environment/take-back-recycling.jsp

Removal of waste batteries and accumulators (Product with embedded battery ONLY)
In case this product contains a battery incorporated within the product which cannot be readily removed by end-users, LG recommends that only qualified professionals remove the battery, either for replacement or for recycling at the end of this product’s working life. To prevent damage to the product, and for their own safety, users should not attempt to remove the battery and should contact LG Service Helpline, or other independent service providers for advice. Removal of the battery will involve dismantling of the product case, disconnection of the electrical cables/contacts, and careful extraction of the battery cell using specialized tools. If you need the instructions for qualified professionals on how to remove the battery safely, please visit
http://www.lge.com/global/sustainability/environment/take-back-recycling

WEEE

Disposal of your old appliance

1. This crossed-out wheeled bin symbol indicates that waste electrical and electronic products (WEEE) should be disposed of separately from the municipal waste stream.
2. Old electrical products can contain hazardous substances so correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. Your old appliance may contain reusable parts that could be used to repair other products, and other valuable materials that can be recycled to conserve limited resources.
3. You can take your appliance either to the shop where you purchased the product, or contact your local government waste office for details of your nearest authorised WEEE collection point. For the most up to date information for your country please see www.lg.com/global/recycling

BATTERY

Disposal of waste batteries/accumulators
This symbol may be combined with chemical symbols for mercury(Hg), cadmium(Cd) or lead(Pb) if the battery Contains more that 0.0005% of mercury, 0.002% of cadmium or 0.004% of lead. All batteries/accumulators should be disposed separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. The correct disposal of Your old batteries/accumulators will help to prevent potential negative consequences for the environment, animal and human health. For more detailed information about disposal of Your old batteries/ accumulators, please contact Your city office, waste disposal service or the shop where You purchased the product. (http://www.lg.com/global/sustainability/environment/take-back-recycling/global-network-europe)
Battery take-back information

1. In case rechargeable battery is included in this product, the entire device should be recycled in compliance with rechargeable battery recycling standards because of the internal battery. To dispose of properly, call (800) 822-8837 or visit www.call2recycle.org.-

UK Notice

Hereby, LG Electronics declares that the radio equipment type PC is in compliance with the relavant statutory requirements. The full text of the UK declaration of conformity is available at the following internet address:
http://www.lg.com/global/support/cedoc/cedoc# The use of the 5150 ­ 5350 MHz band is restricted to indoor use only. This restriction exists in the United Kingdom (UK).

Wireless function S/W : Version 21 or Version 22

Conformity Notice

Hereby, LG Electronics declares that the radio equipment type PC is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.lg.com/global/support/cedoc/cedoc# The use of the 5150 ­ 5350 MHz band is restricted to indoor use only. This restriction exists in Belgium (BE), Bulgaria (BG), Czech Republic (CZ), Denmark (DK), Germany (DE), Estonia (EE), Ireland (IE), Greece (EL), Spain (ES), France (FR), Croatia (HR), Italy (IT), Cyprus (CY), Latvia (LV), Lithuania (LT), Luxembourg (LU), Hungary (HU), Malta (MT), Netherlands (NL), Austria (AT), Poland (PL), Portugal (PT), Romania (RO), Slovenia (SI), Slovakia (SK), Finland (FI), Sweden (SE), Northern Ireland (UK(NI)), Switzerland (CH), Iceland (IS), Liechtenstein (LI) and Norway (NO).

Wireless function S/W : Version 21 or Version 22

SAFETY PRECAUTION

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Only use attachments/accessories specified by the manufacturer. For the permanently connected typed product without the incorporated disconnect device, a readily accessible disconnect device shall be incorporated external to the product. For the pluggable typed product, the socket-outlet shall be installed near the product and shall be easily accessible. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. Batteries shall not be exposed to excessive heat such as sunshine, fire or the like. To reduce the risk of fire or explosion, do not replace the battery by an incorrect type. Dispose of used batteries according to the instructions. Do NOT install this product by yourself as you may injure yourself or cause damage to product. Please contact service personnel authorised by manufacturer. To prevent injury, this apparatus must be securely attached to the wall in accordance with the installation instructions when installing on a wall. All the power sources must be disconnected by removing the power cables to remove all power from the unit.

MFL71831925