Philips AZ700T CD Sound Machine Bluetooth NFC USB Direct 12 Watt User Guide
AZ700T
Quick start guide
Register your product and get support at www.philips.com/support
To download the full user manual, visit www.philips.com/support
To operate this device, you can use either batteries (type: R-20 or D-cells) or AC power
Replace battery
Control play (CD/USB mode only)
| Press and hold to fast-forward or fast-reverse the track during playback, then release to resume play. | |
| Skip to the previous or next MP3 album. | |
| Skip to the previous or next track. | |
| Start or pause play. | |
| Stop play. | |
| REPEAT | Press repeatedly to select a repeat play mode. |
| SHUFFLE | Press to select shuffle play. |
Program tracks
Note:
- To erase the program, press
- Only[
Tune to FM radio stations |
StoreFM radio stations automatically |
Connect through NFC
- Enable the NFC feature on your Bluetooth enabled device.
- Touch the NFC tag on the top of the CD sound machine with back of your Bluetooth device.
- On your Bluetooth device, accept the pairing request with “PhilipsAZ700T”. If necessary, input “0000” as the pairing password.
Connect manually through Bluetooth
- Press BT to select Bluetooth source.
• [BLUETOOTH](Bluetooth) is displayed.
• The CD sound machine enters pairing mode, and [PAIRING] (pairing) is displayed on the screen. - On your Bluetooth device, enable Bluetooth and search for Bluetooth devices.
- In the device list, select [Philips AZ700T]. If necessary, enter default password “0000”.
• After successful pairing and connection, the product beeps twice, and [CONNECTED] (connected) ) is displayed on the screen.
Note:
- If you cannot find [Philips AZ700T] on your device, press
| Amplifier | |
| Max Output Power | 12W |
| Frequency Response | 125 -16000 Hz, -3dB |
| Signal to Noise Ratio | >66 dBA |
| Total Harmonic Distortion | <1 % |
| Audio-in Input | 650 mV RMS |
| Disc | |
| LaserType | Semiconductor |
| Disc Diameter | 12cm/8cm |
| Support Disc | CD-DA CD-R, CD-RW, MP3-CD |
| Audio DAC | 24Bits / 44.1kHz |
| Total Harmonic Distortion | <1% |
| Frequency Response | 125 -16000 Hz, -3dB |
| S/N Ratio | >66 dBA |
| Tuner | |
| Tuning Range | 87.5 – 108MHz |
| Tuning grid | 100 kHz |
| Sensitivity – Mono, 26dB S/N Ratio – Stereo, 46dB S/N Ratio |
<22 dBf <43 dBf |
| Search Selectivity | 26dBf |
| Total Harmonic Distortion | <3% |
| Signal to Noise Ratio | >50 dBA |
| Bluetooth | |
| Bluetooth Version | V3.0 + EDR |
| Range | 10 m (Free space) |
| Frequency band/Output power (for EU compliance) | 2.402GHz – 2.48GHz ISM Band / 7.52dBm |
| NFC frequency | 13.56 MHz |
| General | |
| Power supply – AC Power – Battery | 120V-60Hz; DC 9 V, 6 x 1.5 V/R20 /D CELL |
| Operation Power Consumption | 15 W |
| Standby Power Consumption | < 0.5 W |
| Dimensions – Main Unit (VV x H x D) | 435 x 170 x 271 mm |
| Weight (Main Unit) | 2.7 kg |
- To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture.
- A warning that batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine. fire or the like.
- where the MAINS plug or an appliance coupler is used as the disconnect device. the disconnect device shall remain readily operable
I CLASS 1 LASER PRODUCT - Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No.50. dated June 24. 2007
MMD Hong Kong Holding Limited Units 1006-1007.10th Floor. C-Bons International Center.108 Wai Yip Street. Kwun Tong Kowloon, Hong Kong
FCC Regulatory Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference. and (2) this device must accept any interference received. including interference that may cause undesired operation.
changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
This equipment has been tested and found to comply with the limits for a Class B digital device. pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates. uses and can radiate radio frequency energy and. if not installed and used in accordance with the instructions. may cause harmful interference to radio communications. However. there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception. which can be determined by tuming the equipment off and on. the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radioriV technician for help.
ISED Regulatory Compliance
This device contains licence-exempt transmitters)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1 )This device may not cause interference.(2)This device must accept any interference, including interference that may cause undesired operation of the device.
RF Exposure Compliance
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license.
This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited. or one of its affiliates, and MMD Hong Kong Holding Limited. is the warrantor in relation to this product.
AZ700T_37_QSG_V1.0
