Maytag W10731561C Refrigerator Instruction Manual

W10731561C Refrigerator
Instruction Manual

THANK YOU for purchasing this high-quality product. Register your new refrigerator at www.maytag.com. In Canada, register your refrigerator at www.maytag.ca.
For future reference, please make a note of your product model and serial numbers. These can be located on the inside wall of the refrigerator compartment.
Model Number _______________________________________________
Serial Number _______________________________________________

REFRIGERATOR SAFETY

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean:

You can be killed or seriously injured if you don’t immediately follow instructions.

You can be killed or seriously injured if you don’t follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

  • Plug into a grounded (earthed) outlet.
  • Do not remove the ground prong.
  • Do not use an adapter.
  • Do not use an extension cord.
  • Disconnect power before servicing.
  • Replace all parts and panels before operating.
  • Remove doors from your old refrigerator.
  • Use non-flammable cleaner.
  • Do not store or use petrol, flammable liquids, or gas in the vicinity of this or other electrical appliances. The fumes can cause fires or explosions.
  • Do not store explosive substances such as aerosol cans with a flammable propellant in this refrigerator.
  • Do not use or place electrical devices inside the refrigerator compartments if they are not of the type expressly authorized by the manufacturer.
  • Use two or more people to move and install the refrigerator.
  • Disconnect power before installing ice maker (on ice maker kit ready models only).
  • A qualified service technician must install the waterline and ice maker. See installation instruction supplied with ice maker kit IC13B for complete details.
  • Connect to a potable water supply only.
  • Use a sturdy glass when dispensing ice (on some models).
  • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
  • Children should be supervised to ensure that they do not play with the appliance.
  • To avoid the risk of children becoming trapped and suffocating, do not allow them to play or hide inside the refrigerator.
  • If the power supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person.

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.

Proper Disposal of Your Old Refrigerator
WARNING

Suffocation Hazard
Remove doors from your old refrigerator.
Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous – even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.
Before You Throw Away Your Old Refrigerator or Freezer:

  • Take off the doors.
  • Leave the shelves in place so that children may not easily climb inside.

Important information to know about disposal of refrigerants:
Dispose of a refrigerator in accordance with Federal and Local regulations. Refrigerants must be evacuated by a licensed, EPA-certified refrigerant technician in accordance with established procedures.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator
WARNING
Excessive Weight Hazard
Use two or more people to move and install the refrigerator.
Failure to do so can result in back or another injury.

Remove the Packaging

  • Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.
  • Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see “Refrigerator Safety.”
  • Dispose of/recycle all packaging materials.

When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move it, as damage could occur.

Clean Before Using
After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions in “Refrigerator Care.”
Important information to know about glass shelves and covers:
Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Location Requirements
WARNING

Explosion Hazard
Keep flammable materials and vapors, such as gasoline, away from the refrigerator.
Failure to do so can result in death, explosion, or fire.

IMPORTANT: This appliance is designed for indoor, household use only.
This appliance is intended to be used in household and similar applications such as:

  • Staff kitchen areas in shops, offices, and other working environments,
  • Farmhouses and by clients in hotels, motels, and other residential type environments,
  • Bread and breakfast type environments,
  • Catering and similar non-retail applications.

To ensure proper ventilation for your refrigerator, allow for 1/2″ (1.25 cm) of space on each side and at the top. Allow for 1″ (2.54 cm) of space behind the refrigerator. If your refrigerator has an ice maker, allow extra space at the back for the water line connections. When installing your refrigerator next to a  fixed wall, leave 3³ /4″ (9.5 cm) minimum space between the refrigerator and wall to allow the door to swing open.
NOTE: This refrigerator is intended for use in a location where the temperature ranges from a minimum of 55°F (13°C) to a maximum of 110°F (43°C). The preferred room temperature range for optimum performance, which reduces electricity usage and provides superior cooling, is between 60°F (15°C) and 90°F (32°C). It is recommended that you do not install the refrigerator near a heat source, such as an oven or radiator.

Electrical Requirements
WARNING

Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove the ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person. Do not use a cord that shows cracks or abrasion damage along its length or at either the plug or connector end.
Recommended Grounding Method
A 115 volt, 60 Hz, AC only 15 or 20 A fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.
NOTE: Before performing any type of installation or cleaning, or removing a light bulb, turn cooling off or turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF, and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and turn cooling on or reset the control (Thermostat, Refrigerator, or Freezer Control depending on the model) to the desired setting. See “Using the Controls” in the User Instructions, User Guide, or Use & Care Guide.

Water Supply Requirements
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed here.
TOOLS NEEDED:

  • 7/16″ and 1/2″ Open-end or two adjustable wrenches
  • 1/4″ Drill bit
  • Cordless drill

IMPORTANT:

  • Connect to potable water supply only.
    Do not use water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.
  • All installations must meet local plumbing code requirements.
  • Do not use a piercing-type or 3/16″ (4.76 mm) saddle valve which reduces water flow and clogs more easily.
  • Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain above freezing.
  • For models with water filters, the disposable water filter should be replaced at least every 6 months.

Water Pressure
A cold water supply with water pressure of between 35 and 120 psi (241 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 35 and 120 psi (241 and 827 kPa).
If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa). If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

  • Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.
  • Allow the storage tank on the reverse osmosis system to refill after heavy usage.
  • If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter. See “Water Filtration System.”

If you have questions about your water pressure, call a licensed, qualified plumber

Connect the Water Supply

Read all directions before you begin.
IMPORTANT:

  • Plumbing shall be installed in accordance with the International Plumbing Code and any local codes and ordinances.
  • The gray water tubing on the back of the refrigerator (which is used to connect to the household water line) is a PEX (cross-linked polyethylene) tube. Copper and PEX tubing connections from the household water line to the refrigerator are acceptable and will help avoid off-taste or odor in your ice
    or water. Check for leaks.
    If PEX tubing is used instead of copper, we recommend the following Whirlpool Part Numbers:
    W10505928RP (7 ft [2.14 m] jacketed PEX),
    8212547RP (5 ft [1.52 m] PEX), or
    W10267701RP (25 ft [7.62 m] PEX).
  • Install tubing only in areas where temperatures will remain above freezing.
  • If you turn on the refrigerator before the water line is connected, turn off the ice maker to avoid excessive noise or damage to the water valve.

Connect to Water Line

  1. Unplug the refrigerator or disconnect power.
  2. Turn OFF the main water supply. Turn ON the nearest faucet long enough to clear the line of water.
  3. Find a 1/2″ to 1¹⁄4″ (12.7 mm to 31.8 mm) vertical cold water pipe near the refrigerator.
    IMPORTANT:
    ■ Make sure it is a cold water pipe.
    ■ The horizontal pipe will work, but the following procedure must be followed: Drill on the top side of the pipe, not the bottom. This will help keep water away from the drill. This also keeps normal sediment from collecting in the valve.
  4. Determine the length of copper tubing you need. Measure from the connection on the rear of the refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4″ (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.
  5. Using a cordless drill, drill a 1/4″ hole in the cold water pipe you have selected.
    A. Cold water pipe E. Compression sleeve
    B. Pipe clamp F. Shutoff valve
    C. Copper tubing G. Packing nut
    D. Compression nut
  6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the 1/4″ drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so the washer makes a watertight seal.  Do not overtighten.
  7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with an adjustable wrench. Do not overtighten or you may crush the copper tubing.
  8. Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is clear. Turn OFF the shutoff valve on the water pipe.

    9. Connect to Refrigerator

    1. Create a service loop (minimum diameter of 2 ft [61 cm]) with the copper tubing. Avoid kinks when coiling the copper tubing.
    2. Remove the plastic cap from the water valve inlet port. Place a compression nut and sleeve on the copper tubing.
    3. Insert the end of the copper tubing into the water valve inlet port. Shape tubing slightly so that the tubing feeds straight into the port to avoid kinks.
    4. Slide the compression nut over the sleeve and screw it into the water valve inlet port.
      A. Plastic water tubing C. Compression nut
      B. Sleeve D. Copper tubing
    5. Using an adjustable wrench, hold the nut on the plastic water line to keep it from moving. Then, with a second wrench turn the compression nut on the copper tubing counterclockwise to completely tighten. Do not overtighten.
      A. “P” clamp C. Compression nut
      B. Plastic water line D. Copper tubing
    6. Check connection by pulling on copper tubing. Attach copper tubing to refrigerator cabinet with a “P” clamp. Turn on the water supply to the refrigerator and check for leaks. Correct any leaks.

      7. Complete the Installation

      WARNING

      Electrical Shock Hazard
      Plug into a grounded 3 prong outlet.
      Do not remove the ground prong.
      Do not use an adapter.
      Do not use an extension cord.
      Failure to follow these instructions can result in death, fire, or electrical shock.
      1. Plug into a grounded 3 prong outlet.
      NOTE: Allow 24 hours to produce the first batch of ice.
      Discard the first three batches of ice produced. Allow 3 days to completely fill the ice container.
      Refrigerator Doors and Drawer
      All graphics referenced in the following instructions are included later in this section after “Final Steps.”
      TOOLS NEEDED: 5/16″, 3/8″, 1/4″ hex head socket wrench; a 3/32″ or 1/8″ hex key; #2 Phillips screwdriver; and a flat-blade screwdriver.

      Remove and Replace Handles
      Style 1

      1. Using a 3/32″ or 1/8″ hex key, loosen the two setscrews located on the side of each handle. See Style 1 Handle graphics 1 and 2.
      2. Pull the handle straight out from the door or drawer. Make sure you keep the screws for reattaching the handles.
      3. To replace the handles, reverse the directions.

      Style 2
      To Remove Handles:

      1. Grasp the lower part of the handle firmly, slide the handle up and pull the handle straight out from the door. See Style 2 Handle graphics 1 and 2.

      To Replace Handles:

      1. Position the handle so that the large holes in the mounting clips are down and align the holes with the door studs.
      2. Rotate the handle so that the mounting clips are flat against the door and slide the handle down to engage. See Style 2 Handle graphics 1 and 2.

      Remove Doors and Hinges

      IMPORTANT: Remove food and any adjustable door or utility bins from doors.

      WARNING
      Electrical Shock Hazard
      Disconnect power before removing doors.
      Failure to do so can result in death or electrical shock.

      1. Unplug the refrigerator or disconnect power.
      2. Keep the refrigerator doors closed until you are ready to lift them free from the cabinet.
        NOTE: Provide additional support for the refrigerator door while the hinges are being removed. Do not depend on the door gasket magnets to hold the door in place while you are working.
      3. Starting with the right-hand side door, remove the parts for the top hinge as shown in the Top Hinge graphic. Lift the refrigerator door from the bottom hinge pin.
      4. Remove top hinge cover from the left side refrigerator door.
        Disconnect the wiring plug located on top of the hinge by wedging a flat-blade screwdriver or your fingernail between the two sections. See Connections graphic.
      5. Disconnect the waterline by pulling back on the locking collar while pulling the water line out of the water line connector.
        See Connections graphic.
      6. Remove the parts for the top hinge as shown in the Top Hinge graphic. Lift the left-hand side door from the bottom hinge pin.
      7. Remove the base grille. Remove the two screws fastening the base grille to the cabinet, and set the screws aside. Grasp the grille and pull it toward you.
      8. Using a 3/8″ hex wrench, remove the leveling leg brackets from the bottom of the cabinet. Keep screws for later use.

      Replace Doors and Hinges

      1. Assemble the parts for the top hinge as shown in the Top Hinge graphic. Do not tighten the screws completely.
      2. Replace the parts for the bottom hinge as shown in the Bottom Hinge graphic. Tighten screws. Replace the refrigerator door.
        NOTE: Provide additional support for the refrigerator door while the hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.
      3. Align the door so that the bottom of the refrigerator door aligns evenly with the top of the freezer drawer. Tighten all screws.
      4. Reconnect the wiring plug on top of the left-hand side refrigerator door.
      5. Reconnect the water line by pulling back the locking collar ring while firmly pushing the water line into the connector.
      6. Check for leaks. Replace the top hinge covers.

      Remove and Replace Freezer Drawer
      IMPORTANT: Two people may be required to remove and replace the freezer drawer. Graphics are included later in this section.
      Remove Drawer Front

      1. Open the freezer drawer to full extension.
      2. Loosen the four screws attaching the drawer glides to the drawer front. See Drawer Front Removal graphic.
        NOTE: Loosen screws three to four turns. Keep the screws in the drawer front.
      3. Lift drawer front upward and off the screws. See Drawer Front Removal graphic.

      Replace Drawer Front

      1. Slide the drawer glides out of the freezer compartment. Insert the screws in the top of the drawer front into the slots in the drawer brackets. See Drawer Front Replacement graphic.
      2. Pull the drawer brackets toward you to position the two screws in the bottom of the drawer front into the brackets. See Drawer Front Replacement graphic.
      3. Completely tighten the four screws.

      Final Steps

      1. Replace the base grille.
        WARNING
        Electrical Shock Hazard
        Plug into a grounded 3 prong outlet.
        Do not remove the ground prong.
        Do not use an adapter.
        Do not use an extension cord.
        Failure to follow these instructions can result in death, fire, or electrical shock.
      2. Plug into a grounded 3 prong outlet.
      3. Return all removable door parts to door and food to refrigerator.
      WARNING
      Electrical Shock Hazard
      Disconnect power before removing doors.
      Failure to do so can result in death or electrical shock.

      Door Removal and Replacement

      Adjust the Doors

      IMPORTANT:

  • Your refrigerator has two adjustable, front leveling screws – one on each side of the refrigerator base. If your refrigerator seems unsteady or you want the door to close easier, use the instructions below.
  • Before moving the refrigerator, raise the leveling screws so the front rollers are touching the floor.
  1. Use a Bubble level to check the levelness of the floor where the rear side of the refrigerator will rest. If the refrigerator is not leveled, adjust or add the shim on flooring to create a leveled floor for the rear side wheels. A leveled rear side prevents the refrigerator cabinet from forming a twist.
  2. Remove the two screws fastening the base grille to the cabinet, and set the screws aside. Grasp the grille and pull it toward you.
  3. Raise or lower the cabinet.
    Using a 1/4″ hex driver, turn the leveling screw on each side to raise or lower that side of the refrigerator.
    NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws. This makes it easier to turn the screws. It may take several turns of the leveling screw to adjust the tilt of the refrigerator.
    ■ To raise, turn the leveling screw clockwise.
    ■ To lower, turn the leveling screw counterclockwise.
    A. Leveling screw
    B. Front roller
    ■ Use the bubble level on top of the refrigerator or on its side to level the refrigerator. Check bubble level and at the same time observe the gaps and squareness to the adjacent cabinets, furniture, or trim. If adjacent furnishings are not level, it may not be possible to achieve even gaps when the product is level.
  4. Open the door again to make sure that it closes as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws clockwise. It may take several more turns, and you should turn both screws the same amount.
  5. Replace the base grille.

REFRIGERATOR USE

Opening and Closing Doors
There are two refrigerator compartment doors. The doors can be opened and closed either separately or together.
There is a vertically-hinged seal on the left refrigerator door.

  • When the left side door is opened, the hinged seal automatically folds inward so that it is out of the way.
  • When both doors are closed, the hinged seal automatically forms a seal between the two doors.

Using the Controls

The control center is located on the front of the ice and water dispenser.
Temperature Controls
For your convenience, your temperature controls are preset at the factory. When you first install your refrigerator, make sure the controls are still set to the recommended setpoints as shown.

IMPORTANT:

  • When the power is on, the temperature display shows the setpoint temperature of the compartment.
  • Wait 24 hours for your refrigerator to cool completely before adding food. If you add food before the refrigerator has cooled completely, your food may spoil.
    NOTE: Adjusting the refrigerator and freezer temperature controls to a colder than recommended setting will not cool the compartments any faster.
  • The recommended settings should be correct for normal household refrigerator use. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.
    If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked before adjusting the controls.

Adjusting Controls

The REFRIGERATOR control adjusts the refrigerator compartment temperature. The FREEZER control adjusts the freezer compartment temperature.
If you need to adjust the temperature in either the refrigerator or freezer compartment, use the settings listed in the chart as a guide.
To Adjust Set Point Temperatures:
The first touch of the up or down arrow touchpad displays the current temperature set point.

  • Press the up or down arrow touch pads until the desired temperature set point is displayed.
    NOTE: Except when first turning on the refrigerator, do not adjust either temperature control more than one setting at a time. Wait 24 hours between adjustments for the temperature to stabilize.
CONDITION/REASON: ADJUSTMENT:
REFRIGERATOR too warm REFRIGERATOR Control 1° lower
FREEZER too warm/too little ice FREEZER Control 10 lower
REFRIGERATOR too cold REFRIGERATOR Control 1′ higher
FREEZER too cold FREEZER Control 1′ higher

Cooling On/Off
IMPORTANT:

  • Depending on your model you may have a control center with an On/Off button (Style 1), or you may have a control center without an On/Off button (Style 2).
  • The On/Off control turns off cooling for both compartments and turns off the dispenser. It does not disconnect power from the refrigerator.

Style 1 – Press and hold the On/Off button for 3 seconds. The red LED will light up to indicate that cooling is Off. Press On/Off again to turn cooling back on. The LED will turn off.
Style 2 – Press the Freezer up arrow touchpad until OFF appears in the display. Neither compartment will cool. Press the Freezer or Refrigerator down arrow touchpad to turn cooling back on.

Additional Control Center Features
PowerCold Feature®

The PowerCold®
feature assists with periods of high refrigerator use, full grocery loads, or temporarily warm room temperatures.

  • Press the POWER COLD touchpad to set the freezer and refrigerator to the lowest temperature settings. Press the  POWER COLD touchpad again to return to the normal refrigerator set point.
    NOTE: The PowerCold® feature will automatically shut off in approximately 2 hours. When PowerCold ® is on, the temperature cannot be adjusted.

Humidity Control (on some models)
The Humidity Control feature turns on a heater to help reduce moisture on the door hinge seal. Use in humid environments or when you notice moisture on the door hinge seal. The refrigerator uses more energy when Humidity Control is on.

  • Press HUMIDITY CONTROL to turn on the door heater. Press Humidity Control again to turn off the heater. The LED will be illuminated when Humidity Control is on.

Temp Alarm
The Temp Alarm feature provides temperature information in the event of a power outage.
Power outage: During a power outage, if the temperatures in the refrigerator and freezer compartments exceed normal operating temperatures, the highest temperature reached will be displayed.

  • Press the TEMP ALARM touchpad until the indicator light is lit, to turn on this feature. Press and hold Temp Alarm for 3 seconds until the indicator light goes off to turn off this feature.

Temperature alarm: An alarm will sound repeatedly if the freezer or refrigerator compartment temperatures exceed normal operating temperatures for an hour or more.
The temperature displays will alternately show the current temperatures and the highest temperatures the compartments reached.

  • Press the TEMP ALARM touchpad once to stop the audible alarm and alternating temperature displays. The Temp Alarm light will continue to flash until the refrigerator returns to the set temperature.

Door Alarm
The Door Alarm feature sounds a chime every few seconds when the refrigerator door has been left open for 5 continuous minutes. The chime will sound until the door is closed or Door Alarm is turned off.

  • Press the DOOR ALARM touchpad to turn this feature on or off. The indicator light will be lit when the Door Alarm feature is on.

Filter Reset
See “Water Filtration System.”

User Preferences
The control center allows you to set user preferences if desired.
Temperature Display (F_C)
This preference allows you to change the temperature display.
F – Temperature in degrees Fahrenheit
C – Temperature in degrees Celsius
Alarm (AL)
This preference allows you to turn off the sound of all alarms.
ON – You will hear the alarm sound.
OFF – You will not hear the alarm sound.
Auto Light Level Selection (LL)
This preference allows you to adjust the dispenser light level from dimmest to brightest (settings 1 through 9).
NOTE: The Auto Light feature on the control center must be selected to activate this preference.
Sabbath Mode (SAB)
ON – All control center lights, interior lights, and alarm tones will be disabled.
OFF – All control center lights, interior lights, and alarm tones will be enabled.
NOTE: Press and hold the DOOR ALARM touchpad for 3 seconds to restore all lights.

To Access the User Preferences Menu:

  1. Press and hold the Door Alarm touchpad for 3 seconds. The preference name will appear in the Freezer display and the preference status (F/C or ON/OFF) will appear in the Refrigerator display.
  2. Use the Freezer up or down arrow touchpads to scroll through the preference names. When the desired preference name is displayed, press the Refrigerator up or down arrow touchpads to change the preference status.
  3. Set your preferences by pressing and holding the DOOR ALARM touchpad for 3 seconds.

Crisper Humidity Control

You can control the amount of humidity in the moisture-sealed crisper. Depending on your model, adjust the control to any setting between FRUIT and VEGETABLES or LOW and HIGH.
FRUIT/LOW (open) for best storage of fruits and vegetables with skins.
VEGETABLES/HIGH (closed) for best storage of fresh, leafy vegetables.

Ice Maker and Ice Storage Bin
IMPORTANT:

  • Flush the water system before turning on the ice maker. See “Water and Ice Dispenser.”
  • The ice maker and storage bin are located in the upper lefthand side of the refrigerator compartment.

Turning the Ice Maker On/Off
The On/Off switch is located on the ice maker.
To turn on the ice maker, press the switch to the ON position.
To manually turn off the ice maker, press the switch to the OFF position.
NOTE: Your ice maker has an automatic shutoff. The ice maker sensors will automatically stop ice production, but the control will remain in the ON position.

Removing and Replacing Ice Storage Bin
To Remove the Ice Storage Bin:

  1. Hold the base of the storage bin and press the release button on the lower right.
  2. Pull the storage bin out until resistance is felt. Lift up the front of the ice bin and remove.
  3. Press the switch to the OFF position

To Replace the Ice Storage Bin:
IMPORTANT: It may be necessary to turn the auger driver, behind the ice bin, counterclockwise to properly align the ice bin with the auger driver. The ice storage bin must be locked in place for proper ice dispensing.

  1. Press the switch to the ON position
  2. Slide the ice bin into the guide rails located on either side of the enclosure.
  3. Push the ice bin in until resistance is felt. Raise the front slightly and push the ice bin in until an audible “click” is heard.

Ice Production Rate

  • Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill the ice storage bin.
  • The ice maker should produce approximately 8 to 12 batches of ice in a 24-hour period.
  • To increase ice production, lower the freezer and refrigerator temperature. See “Using the Controls.” Wait 24 hours between adjustments.

Remember

  • The quality of your ice will be only as good as the quality of the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.
  • Do not use anything sharp to break up the ice in the bin. This can cause damage to the ice bin and dispenser mechanism.
  • Do not store anything on top of the ice maker or in the ice storage bin.

Water and Ice Dispenser
IMPORTANT:

  • After connecting the refrigerator to a water source or replacing the water filter, flush the water system. Use a sturdy container to depress and hold the water dispenser pad for 5 seconds, then release it for 5 seconds. Repeat until water begins to flow. Once water begins to flow, continue depressing and releasing the dispenser pad (5 seconds on, 5 seconds off) until a total of 4 gal. (15 L) has been dispensed. This will flush air from the filter and water dispensing system, and prepare the water filter for use. Additional flushing may be required in some households. As air is cleared from the system, water may spurt out of the dispenser.
    NOTE: After 5 minutes of continuous dispensing, the dispenser will stop dispensing water to avoid flooding. To continue dispensing, remove the container and press the dispensing lever again.
  • The dispenser will dispense either water or cubed ice.
  • Allow 24 hours for the refrigerator to cool down and chill water. Dispense enough water every week to maintain a fresh supply.
  • Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

Dispense Ice and Water

WARNING
Cut Hazard
Use a sturdy glass when dispensing ice.
Failure to do so can result in cuts.

  1. Select water or cubed ice by touching the word WATER or ICE on the control panel. The light above the control indicates your selection.
  2. Press a sturdy container against the dispenser lever.
    IMPORTANT: You do not need to apply a lot of pressure to the lever in order to activate the dispenser. Pressing hard will not make the water or ice dispense faster or in greater quantities.
  3. Remove the container to stop dispensing.

Dispenser Light
NOTES:

  • The dispenser lights are LEDs that should not need to be changed.
  • When you use the dispenser, the lever will automatically turn the light on. If you want the light to be on continuously, you may choose either On or Auto.

Auto: The light sensor monitors the light level in the room. The dispenser light will illuminate at half-power when the light level is low. To activate the Auto option, press the LIGHT button. The auto indicator light will illuminate.
On: For continuous light, press the LIGHT button a second time. The On indicator light will illuminate.
Off: To turn the dispenser light off, press the LIGHT button a third time.

Dispenser Lock
The dispenser can be locked for easy cleaning or to avoid unintentional dispensing by small children and pets.
NOTE: The dispenser lock does not shut off power to the product, to the ice maker, or to the dispenser light. It just deactivates the dispenser lever.
To Lock and Unlock Dispenser:

  • Press and hold the CONTROL LOCK touchpad for 3 seconds to lock the dispenser. The indicator light will illuminate when the Lock is on.
  • Press and hold the CONTROL LOCK touchpad again for 3 seconds to unlock the dispenser. The indicator light will turn off.

Water Filtration System
The water filter is located in the upper right-hand corner of the refrigerator compartment.
Do not use water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

Water Filter Status Lights
When a water filter has been installed in the refrigerator the water filter status lights will remind you when it is time to order and replace your water filter.

  • The Order light (yellow) will illuminate when 90% of the volume of water for which the filter is rated has passed through the filter OR 5 months have passed since the filter was installed.
  • The Replace light (red) will illuminate when the rated volume of water has passed through the filter OR 6 months have passed since the filter was installed. A new water filter should be installed immediately when the Replace light is illuminated.

The disposable water filter should be replaced at least every 6 months OR earlier if the flow of water to your water dispenser or ice maker decreases noticeably.
Reset Water Filter Status
After replacing the water filter, press and hold RESET FILTER or FILTER RESET (depending on your model) for 3 seconds. The Order and Replace indicator lights will blink and then go off when the system is reset. See “Using the Controls.”

Replacing the Water Filter
To purchase a replacement water filter, model UKF8001AXX-750 or UKF8001AXX-200, see “Accessories.”
IMPORTANT: Air trapped in the water system may cause water and filter to eject. Always dispense water for at least 2 minutes before removing the filter or blue bypass cap.

  1. Turn filter counterclockwise to remove.
  2. Remove the sealing label from the replacement filter and insert the filter end into the filter head.
  3. Turn the filter clockwise until it stops. Snap the filter cover closed.
  4. Flush the water system. See “Water Dispenser” or “Water and Ice Dispenser.”

NOTE: The dispenser feature may be used without a water filter installed. Your water will not be filtered. If this option is chosen, replace the filter with the blue bypass cap.

REFRIGERATOR CARE

Cleaning
WARNING


Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.
However, clean both sections about once a month to avoid odor buildup. Wipe up spills immediately.
IMPORTANT: Because air circulates between both sections, any odors formed in one section will transfer to the other. You must thoroughly clean both sections to eliminate odors. To avoid odor transfer and drying out of food, wrap or cover foods tightly.
To Clean Your Refrigerator: 
NOTE: Do not use abrasive or harsh cleaners such as window sprays, scouring cleansers, flammable fluids, cleaning waxes, concentrated detergents, bleaches, or cleansers containing petroleum products on plastic parts, interior and door liners or gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools.

  1. Unplug the refrigerator or disconnect power.
  2. Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a mild detergent in warm water.
  3. Wash stainless steel and painted metal exteriors with a clean sponge or soft cloth and a mild detergent in warm water.
    ■ To keep your stainless steel refrigerator looking like new and to remove minor scuffs or marks, it is suggested that you use the manufacturer’s approved Stainless Steel Cleaner and Polish, Part Number 20000008. To order the cleaner, call 1-800-901-2042 U.S.A. or 1-800-807-6777 Canada.
    IMPORTANT: This cleaner is for stainless steel parts only! Do not allow the Stainless Steel Cleaner and Polish to come into contact with any plastic parts such as the trim pieces, dispenser covers, or door gaskets. If unintentional contact does occur, clean the plastic part with a sponge and mild detergent in warm water. Dry thoroughly with a soft cloth.
  4. There is no need for routine condenser cleaning in normal home operating environments. If the environment is particularly greasy or dusty, or there is significant pet traffic in the home, the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency. If you need to clean the condenser:
    ■ Remove the base grille.
    ■ Use a vacuum cleaner with a soft brush to clean the grille, the open areas behind the grille, and the front surface area of the condenser.
    ■ Replace the base grille when finished.
  5. Plugin the refrigerator or reconnect power.

Changing the Light Bulb

IMPORTANT: The light bulbs in both the refrigerator and freezer compartments use LED bulbs, incandescent bulbs or a combination of the two. If the lights do not illuminate when the refrigerator and/or freezer door is opened, call for assistance or service. See “Warranty” for phone numbers.

  1. Unplug the refrigerator or disconnect power.
  2. Remove the light shield (on some models).
    ■ Top of the refrigerator compartment – Squeeze both sides of the light shield while pulling downward to remove.
    ■ Beneath ice storage enclosure (on some models) – Press along the upper edge of light shield and roll light shield forward to remove.
  3. Replace the burned-out bulb(s) with a bulb of the same size, shape, and wattage.
    ■ To replace the burned-out LED bulb with a LED bulb, order Part Number W10565137 (3.6 watts).
    NOTE: Some LED replacement bulbs are not recommended for wet/damp environments. The refrigerator and freezer compartments are considered to be wet/damp environments. If using a brand of LED bulb other than the recommended LED bulb, before installation, read and follow all instructions on the LED packaging.
    ■ When replacing an incandescent bulb, use only incandescent bulbs for household appliances with a maximum of 40 watts.
    ■ Reinstall bulb shield/shroud after replacing incandescent bulb(s).
  4. Plug in the refrigerator or reconnect power.

TROUBLESHOOTING

First, try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call, refer to the warranty page in this manual, or visit www.maytag.com/product_help.
In Canada, visit www.maytag.ca.
Contact us by mail with any questions or concerns at the address below:
In the U.S.A.:
Maytag Brand Home Appliances
Customer Experience Center
553 Benson Road
Benton Harbor, MI 49022-2692
In Canada:
Maytag Brand Home Appliances
Customer Experience Centre
200 – 6750 Century Ave.
Mississauga, Ontario L5N 0B7
Please include a daytime phone number in your correspondence.

Refrigerator Operation

The refrigerator will not operate
WARNING

Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove the ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.

  • Is the power cord unplugged? Plug into a grounded 3 prong outlet.
  • Is the outlet working? Plug in a lamp to see if the outlet is working.
  • A household fuse has blown or circuit breaker tripped? Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician.
  • Are controls on? Make sure the refrigerator controls are on. See “Using the Control(s).”
  •  New installation? Allow 24 hours following installation for the refrigerator to cool completely.

NOTE: Adjusting the temperature controls to the coldest setting will not cool either compartment more quickly.

The motor seems to run too much
Your new refrigerator may run longer than your old one due to its high-efficiency compressor and fans. The unit may run even longer if the room is warm, a large food load is added, doors are opened often, or if the doors have been left open.

The refrigerator seems noisy
Refrigerator noise has been reduced over the years. Due to his reduction, you may hear intermittent noises from your new refrigerator that you did not notice from your old model. Below are listed some normal sounds with explanations.

  • Buzzing – heard when the water valve opens to fill the ice maker
  • Pulsating – fans/compressor adjusting to optimize performance
  • Hissing/Rattling – the flow of refrigerant, movement of water lines, or from items placed on top of the refrigerator
  • Sizzling/Gurgling – water dripping on the heater during defrost cycle
  • Popping – contraction/expansion of inside walls, especially during initial cool-down
  • Water running – may be heard when the ice melts during the defrost cycle and water runs into the drain pan
  • Creaking/Cracking – occurs as ice is being ejected from the ice maker mold

The doors will not close completely

  • Did the door block open? Move food packages away from the door.
  • Bin or shelf in the way? Push the bin or shelf back into the correct position.

The doors are difficult to open

WARNING


Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.

  • Are gaskets dirty or sticky? Clean gaskets and contact surfaces with mild soap and warm water. Rinse and dry with a soft cloth.

Temperature and Moisture

Temperature is too warm

  • New installation? Allow 24 hours following installation for the refrigerator to cool completely.
  • Door(s) opened often or left open? Allows warm air to enter the refrigerator. Minimize door openings and keep doors fully closed.
  • A large load of food added? Allow several hours for the refrigerator to return to normal temperature.
  • Controls set correctly for the surrounding conditions? Adjust the controls to a setting colder. Check the temperature in 24 hours. See “Using the Control(s).”

Temperature is too cold in a refrigerator

  • Refrigerator air vent blocked? If the air vent located in the top, left, rear corner of the refrigerator compartment is blocked by items placed directly in front of it, the refrigerator will get too cold. Move items away from the air vent.
  • Ice storage bin in the correct position? See “Ice Maker and Ice Storage Bin.”
  • Controls set correctly for the surrounding conditions? Adjust the controls a setting warmer. Check the temperature in 24 hours. See “Using the Control(s).”

There is interior moisture buildup
NOTE: Some moisture buildup is normal.

  • Humid room? Contributes to moisture buildup.
  • Door(s) opened often or left open? Allows humid air to enter the refrigerator. Minimize door openings and keep doors fully closed.

Ice and Water

The ice maker is not producing ice or not enough ice

  • Refrigerator connected to a water supply and the supply shutoff valve turned on? Connect refrigerator to water supply and turn water shutoff valve fully open.
  • Kink in the water source line? A kink in the line can reduce water flow. Straighten the water source line.
  • Ice maker turned on? Make sure ice maker is ON. See “Ice Maker and Ice Storage Bin.”
  • New installation? Wait 24 hours after ice maker installation for ice production to begin. Wait 72 hours for full ice production.
  • Refrigerator door closed completely? Close the door firmly. If it does not close completely, see “The doors will not close completely.”
  • A large amount of ice recently removed? Allow 24 hours for ice maker to produce more ice.
  • Ice cube jammed in the ice maker ejector arm? Remove ice from the ejector’s arm with a plastic utensil.
  • The water filter installed on the refrigerator? Remove the filter and operate ice maker. If ice volume improves, then the filter may be clogged or incorrectly installed. Replace the filter or reinstall it correctly.
  • Reverse osmosis water filtration system connected to your cold water supply? This can decrease water pressure. See “Water Supply Requirements.”

The ice cubes are hollow or small
NOTE: This is an indication of low water pressure.

  • Water shutoff valve not fully open? Turn the water shutoff valve fully open.
  • Kink in the water source line? A kink in the line can reduce water flow. Straighten the water source line.
  • Is the water filter installed on the refrigerator? Remove the filter and operate ice maker. If ice quality improves, then the filter may be clogged or incorrectly installed. Replace the filter or reinstall it correctly.
  • Reverse osmosis water filtration system connected to your cold water supply? This can decrease water pressure. See “Water Supply Requirements.”
  • Do questions remain regarding water pressure? Call a licensed, qualified plumber.

Off-taste, odor or gray color in the ice

  • New plumbing connections? New plumbing connections can cause discolored or off-flavored ice.
  • Did ice store too long? Discard ice. Wash ice bin. Allow 24 hours for the ice maker to make new ice.
  • Odor transfer from food? Use airtight, moisture-proof packaging to store food.
  • Are there minerals (such as sulfur) in the water? A water filter may need to be installed to remove the minerals.
  • Is the water filter installed on the refrigerator? Gray or dark discoloration in ice indicates that the water filtration system needs additional flushing. Flush the water system before using a new water filter. Replace the water filter when indicated. See “Water Filtration System.”

The water dispenser will not operate properly

  • Refrigerator connected to a water supply and the supply shutoff valve turned on? Connect refrigerator to water supply and turn water shutoff valve fully open.
  • Kink in the water source line? Straighten the water source line.
  • New installation? Flush and fill the water system. See “Water and Ice Dispensers.”
  • Is the water pressure at least 35 psi (241 kPa)? The water pressure to the home determines the flow from the dispenser. See “Water Supply Requirements.”
  • Is the water filter installed on the refrigerator? Remove the filter and operate the dispenser. If water flow increases, the filter may be clogged or incorrectly installed. Replace the filter or reinstall it correctly.
  • Water dispenser measured fill feature is not dispensing an accurate amount of water? Calibrate the water dispenser. See “Water and Ice Dispensers.”
  • Refrigerator door closed completely? Close the door firmly. If it does not close completely, see “The doors will not close completely,” earlier in this section.
  • Recently removed the doors? Make sure the water dispenser wire/tube assembly has been properly reconnected at the top of the refrigerator door. See “Refrigerator Doors and Drawer.”
  • Reverse osmosis water filtration system connected to your cold water supply? This can decrease water pressure. See “Water Supply Requirements.”

Water is leaking from the dispenser system
NOTE: One or two drops of water after dispensing is normal.

  • Glass not being held under the dispenser long enough? Hold the glass under the dispenser 2 to 3 seconds after releasing the dispenser lever.
  • New installation? Flush the water system. See “Water and Ice Dispensers.”
  • Recently changed water filter? Flush the water system. See “Water and Ice Dispensers.”

Water from the dispenser is warm
NOTE: Water from the dispenser is only chilled to 50°F (10°C).

  • New installation? Allow 24 hours after installation for the water supply to cool completely.
  • Recently dispensed large amount of water? Allow 24 hours for water supply to cool completely.
  • Water not been recently dispensed? The first glass of water may not be cool. Discard the first glass of water.
  • Refrigerator connected to a cold water pipe? Make sure the refrigerator is connected to a cold water pipe. See “Water Supply Requirements.”

PERFORMANCE DATA SHEETS

Interior Water Filtration System
Model UKF8001AXX-750 Capacity 750 Gallons (2839 Liters)

System tested and certified by NSF International against NSF/ANSI Standard 42 for the reduction of Chlorine Ta ste and Odor, Particulate Class I*; and against NSF/ANSI Standard53 for the reduction of Lead, Mercury, Atrazine, Benzene, p-Dichlorobenzene, Carbofuran, Toxaphene, Cysts, Turbidity, Asbestos, Tetrachloroethylene, and Lindane.

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The the concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the the permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53

Substance Reduction
Aesthetic Effects		 NSF
Reduction
Requirements