KENWOOD CBL30 SoupEasy+ Blender Instructions

KENWOOD CBL30 SoupEasy+ Blender

Safety

  • Read these instructions carefully and retain for future reference.
  • Remove all packaging and any labels.
  • If the plug or cord is damaged it must, for safety reasons, be replaced by Kenwood or an authorised Kenwood repairer in order to avoid a hazard.
  • Ensure the cord is fully unwound from the cord storage area 10 before using the blender.
  • Do not touch the sharp blades. Handle the blades with care to avoid injury when emptying the goblet and during cleaning.
  • Always switch off and unplug the appliance before putting your hands or utensils in the goblet whilst fitted to the power unit.
  • Switch off the appliance and disconnect from the power supply before changing accessories or approaching parts that move in use.
  • The blender lid is fitted with a safety switch and the motor will only operate if the lid is correctly fitted. Do not attempt to operate without the lid fitted.
  • Never use a damaged appliance. Get it checked or repaired: see `Service and Customer Care’.
  • Never leave the appliance unattended when it is operating.
  • Do not fill below the minimum levels or exceed the maximum fill levels marked on the inside of the goblet.
  • Do not use your appliance for blending for longer than 3 minutes without a 15 minute rest period. Processing continuously for longer periods can damage your appliance.
  • CAUTION: Before removing the lid from the goblet switch off and wait until the blades have completely stopped.
  • Smoothie recipes – never blend frozen ingredients that have formed a solid mass during freezing, break it up before adding to the goblet.
  • Do not process hard spices such as Nutmeg or dried Turmeric root as they may damage the blade.
  • Never run the blender empty.
  • Do not use the blender as a storage container. Keep it empty before and after use.
  • Do not let excess cord hang over the edge of a table or worktop or touch hot surfaces.
  • Never place this appliance on or near a hot gas or electric burner or where it could touch a heated appliance.
  • This appliance should only be used on a stable, flat heat resistant surface or table.
  • CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to an electrical supply that is switched on and off regularly
  • Misuse of your appliance can result in injury.
  • Caution: Do not operate the appliance on an inclined surface.
  • Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved.
  • Children should be supervised to ensure that they do not play with the appliance.
  • This appliance shall not be used by children. Keep the appliance and its cord
  • Only use the appliance for out of reach its intended of children. domestic use. Kenwood will not accept any liability if the appliance is subject to improper use, or failure to comply with these instructions.
Hot Blending
  • CAUTION: Avoid contact with steam coming out of the spout area when pouring and out of the lid and filler cap during operation. O Always fit the filler cap and do not remove the filler cap or add ingredients during the blending cycle.
  • CAUTION: the outside of the goblet, lid and filler cap will get hot during use and will remain HOT after the appliance is switched off. Always remove the lid using the lid tab and lift and pour using the goblet handle.
  • Be careful if hot liquid is poured into the appliance as it can be ejected out of the appliance due to sudden steaming.
  • To minimise the possibility of scalding when blending hot ingredients keep hands and other exposed skin away from the lid and filler cap to prevent possible burns. If necessary protect your hands with a cloth or oven gloves when handling.
  • CAUTION: Blending very hot ingredients may result in hot liquid and steam being forced suddenly past the lid or filler cap. 
  • NEVER exceed the hot liquid marking on the goblet if processing hot liquids, such as soups.
  • The heating element surface is subject to residual heat after use.
  • When using the hot blending function or the steamer basket keep the blender away from walls and overhanging cupboards: the steam could damage them.
  • Be careful of steam escaping from the steamer basket particularly when removing the lid during or after cooking.
  • Take care when handling parts; any liquid, condensation, steamer basket or goblet will be very hot. Always use the handle supplied to remove the basket.

Food safety

  • Cook meat (including poultry), fish and seafood thoroughly.
  • Always ensure food is piping hot before eating.
  • Food should be eaten shortly after cooking or allowed to cool quickly and then refrigerated as soon as possible.

Care and Cleaning

Refer to illustration

  • The marked on the product indicates the parts that must not be immersed in water or any other liquids.
  • Do not immerse the motor unit or goblet in water
  • Always switch off the appliance and disconnect from the supply if it is left unattended and before assembling, disassembling or cleaning.
  • Never let the motor unit, cord or plug get wet.
  • WARNING: Be careful to avoid any spillage on the connector, during cleaning, filling or pouring.
  • Keep the connectors clean and dry. Wipe the motor unit with a damp cloth, then dry.
  • Use the ‘Easy Clean’ preset to clean the inside of the goblet and blades. Add 1.4 litre water and 2 drops of washing up liquid. DO NOT add too much detergent as this may cause the liquid to overflow.
  • Plug in and select the ‘Easy Clean’ preset. Once the preset finishes rinse the blade and inside of the goblet.
  • If food sticks or burns on the inside of the goblet, remove as much as possible using a spatula. Fill the goblet with warm soapy water and allow to soak.
  • Remove any stubborn deposits using a cleaning brush. Any discolouration of the goblet will not affect its performance.
Before plugging in
  • Make sure your electricity supply is the same as the one shown on the underside of your appliance.
  • This appliance conforms to EC Regulation 1935/2004 on materials and articles intended to come into contact with food.

Before Using For The First Time

  • Wash the parts: see ‘Care and Cleaning’.

Key

① Filler cap
② Lid
③ Steamer basket handle
④ Steamer basket
⑤ Goblet with fixed blades
⑥ Handle
⑦ Power unit
⑧ Display screen
⑨ Rotary dial
⑩ Cord storage
⑪ Time/Temperature Select button
⑫ (–) Time/Temp button
⑬ (+) Time/Temp button
⑭ Manual preset
⑮ Smooth Soup preset
⑯ Chunky Soup preset
⑰ Compote preset
⑱ Easy Clean preset
⑲ Pulse/Ice
⑳ Speed selector 1 – 4
㉑ Start/Stop button

To Set up your Cooking Blender

Refer to illustration

To use the Cooking/Heating Presets

Refer to illustration

  1. Add the food to the goblet. For best results always add the liquid last.
    ● Ensure the fill level is between the 800ml MIN and 1400ml MAX mark inside the goblet. Do not fill above 1400ml when processing hot ingredients.
  2. Fit the lid and filler cap – turn clockwise to lock.
  3. Turn the rotary dial to the required preset. Refer to the Preset chart for temperature and time information.
  4. Press the Start/Stop button to start the preset – the display screen will start to countdown.
  5. At the end of the preset time the blender will automatically stop and the display will flash and show ‘End’ on the screen.
    ● To pause the preset at any time press the ‘Start/Stop’ button – the countdown will stop and the screen with flash. To resume, press the ‘Start/Stop’ button again.

Manual Cooking

Refer to illustration

Function Function explained
Manual Time and Temperature button. To manually select the time and temperature, press the
button to switch between time and temperature.
Use the (+/-) buttons to adjust the time and temperature,
Increase or decrease the time and temperature buttons. After pressing the time/temperature button use the (+) and (-) buttons to change the time and temperature (°C).
The time can be adjusted in 5 second increments from 05:00 – 60:00.
To scroll through the time quicker press and hold down the (+ or -) button.
The temperature can be adjusted in 5°C increments from
40 – 100°C.
Once the time and temperature have been selected, press the Start/Stop button to start the countdown.

Cooking/Heating Presets

Preset

(MAX)

°C

(mins)

Blending Cycle (mins)

(mins)

Manual 800ml – 1.4L 40 – 100 05:00 –
60:00
0 0
Smooth Soup 800ml – 1.4L 100 25:00 40
Chunky Soup 800ml – 1.4L 100 30:00 0 40

Compote

Compote 800g Fruit 100ml Liquid 100 35:00 0
Easy Clean 1.4L 65 – 75 3:00 2:00
00:20
On/00:30 OFF X 3 + 00:30 ON
0
  • Compote preset – throughout the cooking cycle the blades will intermittently stir and blend the ingredients.
  • Keep Warm – At the end of the ‘Smooth’ and ‘Chunky’ Soup presets the blender will automatically go into the ‘Keep Warm’ mode and countdown from 40 minutes.
Hints and Tips
  • Cut ingredients into even sized pieces as this will assist with even cooking.
  • Add food items such as milk, cream, yoghurt etc., during the last 10 minutes of cooking. This will prevent the mix from foaming over and stop burning or sticking to the bottom of the goblet.
  • When making soups and where required we recommend that meats are browned and vegetables sautéed in a pan on the stove prior to adding to the blending goblet to ensure cooked thoroughly.
  • Use hot stock to reduce the cooking time required.
  • If you require a smoother result after cooking use the blender selector speed 1 -4.

Bechamel Sauce

To make milk based sauces
Add 500ml milk, 45g plain flour and 45g butter to the goblet. Use the Easy Clean programme X 2 or 3 times (Maximum time of 9 minutes

To use the Steamer Basket

Refer to illustration

  1. Add 500 ml water to the goblet.
    ● 500 ml will be enough for 30 minutes cooking. For longer cooking times you may need to add for more water.
    ● The steamer basket can be used in conjunction with the chunky soup preset to cook whole ingredients such as meat, fish and vegetables at the same time as the soup.
  2. Fit the basket by aligning the slot for the removable handle with the spout area – the grooves on the basket should fit over the ribs in the goblet.
  3. Add the food to be cooked to the basket.
  4. Fit the lid and filler cap, then select the manual or chunky soup preset.
  5. Press the Start/Stop button and the time will countdown.
  6. At the end of the cooking cycle switch off and fit the handle to the basket to remove the food.

°C

(mins)

Water/Liquid

Manual

100°C 15:00 – 50:00

500ml

Chunky

Chunky Soup

100°C 30:00

500ml – 800ml

Steamer Basket Cooking Guide

Food

(MAX)

(mins)

Potatoes 3-4cm pieces 300g 20:00 – 30:00
Carrots 2cm slices 200g 20:00 – 25:00
Broccoli 100g 15:00 – 20:00
Fish Fillet 100 – 150g 20:00 – 25:00
Chicken Breast 2 x 150g 30:00 – 40:00
Hints and Tips
  • If you are steaming for more than 30 minutes you will need to top up the water.
  • For best results and even cooking do not overfill the basket.
  • Liquid left in the bowl is good for making soup or stock. But be careful it will be very hot.
  • Leave gaps between pieces of food.
  • Similar sized pieces of food cook more evenly.
  • If your food is not cooked enough, check the water level, top up and reset the time manually.
  • Do not allow the unit to boil dry, top up with water as necessary

Blending Function (without heat)

Refer to illustration


  1. Add the food to the goblet. For  best results always add the frozen ingredients in last.
    ● Ensure the fill level is between the 500ml MIN and 1750ml MAX mark inside the goblet.
  2. Fit the lid and filler cap – turn clockwise to lock.
  3. Turn the rotary dial to the required speed or Pulse. Refer to the cold blending chart for speed and time information.
  4. Press the Start/Stop button to start – the display screen will start to count up.
    Note : The blender will switch off automatically after 3 minutes continuous operation. To reset the time press ‘Start’.
    ● To pause the blending cycle press the ‘Start/Stop’ button. To resume, press the ‘Start/Stop’ button again.
  5. To end or cancel the blending cycle press the ‘Start/Stop’ button and turn the dial to ‘O’.

Pulse Function

  • Use the  in short bursts to operate the motor in a Start/Stop action. The pulse will operate for as long as the Start/Stop button is pressed.
  • Use for crushing ice.
Recipe

(mins : secs)

(MAX)

Milkshakes 3 – 4 01:00 – 01:30 500 – 1000ml
Cold Drinks & Smoothies 3 – 4 01:00 – 02:00 500 – 1750ml
Chilled Soups 4 02:00 – 03:00 500 – 1750ml
Batter 1 – 3 01:00 1000ml
Cold purees 3 – 4 00:30 – 01:00 300g
Ice Crushing 00:20 – 00:40 6 X   125g
Honey & Prune Spread
Pitted Prunes 00:05 360g
Honey 320g
Add Water 00:08 300g
Hints and Tips
  • Use the pulse to process ice in a stop/start operation for best results.
  • Smoothies – place the fresh fruit and liquid ingredients in first (includes yoghurt, milk and fruit juices). Then add ice or frozen ingredients (includes frozen fruit, ice or ice cream)
  • To blend dry ingredients – cut into pieces, remove the filler cap, then with the machine running, drop the pieces down one by one. Keep your hand over the opening. For best results empty regularly.
  • Thick mixtures, e.g. pâtés and dips, may need scraping down. If the mixture is difficult to process, add more liquid.

Cord storage

Push any excess cord into the storage area at the back of the power unit ➉ .

Service and Customer Care

  • If you experience any problems with the operation of your appliance, before requesting assistance refer to the ‘Troubleshooting Guide’ section in the manual or visit www.kenwoodworld.com.
  • Please note that your product is covered by a warranty, which complies with all legal provisions concerning any existing warranty and consumer rights in the country where the product was purchased.
  • If your Kenwood product malfunctions or you find any defects, please send it or bring it to an authorised KENWOOD Service Centre. To find up to date details of your nearest authorised KENWOOD Service centre visit www.kenwoodworld.com or the website specific to your Country.
  • Designed and engineered by Kenwood in the UK.
  • Made in China.

IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH THE EUROPEAN DIRECTIVE ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE)
At the end of its working life, the product must not be disposed of as urban waste. It must be taken to a special local authority differentiated waste collection centre or to a dealer providing this service.

Troubleshooting Guide

Problem Cause Solution
Blender not operating. Display screen not on. Check appliance is plugged into the power supply.
Goblet not fitted to power unit.
‘JUG’ will appear on the screen.
Check that the blender is fitted to the power unit correctly.
Lid not fitted correctly. ‘OPEN’ will appear on the screen. Check that lid is correctly locked on.
Liquid splashing out of lid and filler cap. Goblet overfilled. Check that ingredients is not filled above the max level marked inside the goblet.
Hot milk frothing up and overflowing. Do not fill hot liquid above 1.4l and add milk within last 10 minutes of cooking.
Easy Clean programme
– more than 1.4 litre of water added and too much detergent added.
Add 1.4 litre water and 2 drops of washing up liquid.
Ingredients burning on the bottom of the goblet. Milk being heated. To prevent burning add milk, cream etc., within last 5-10 minutes of the preset. .
Insufficient liquid added. Add more liquid.
Poor Blending performance. Insufficient processing time. Blend for longer using the speed selector 1 – 4.
Insufficient liquid added. Add more liquid.
Large pieces of food or too much ingredients being processed. Remove some of the ingredients and chopped the food down into small even sized pieces.
Food insufficiently cooked. Large pieces of food or too much ingredients being processed. Remove some of the ingredients and chopped the food down into small even sized pieces.
Raw meat or lentils being cooked. It is recommend that meats are browned in a pan on the stove prior to adding to the blending goblet to ensure cooked thoroughly.
Use hot stock to assist the cooking process.
Insufficient cooking time. Use hot stock to assist the cooking process.
Use the manual programme to extend the cooking time.
Smooth or Chunky Soup programme in the keep warm mode. Normal Function.

To stop the Keep Warm mode turn the dial to ‘0’ position.

‘End’ shown and flashing on screen. Unit beeping. Cold blending cycle reached 3 minutes and unit automatically stopped. To reselect the speed press ‘Start’ or to stop turn the dial to ‘O’.
It is recommended to allow the blender to cool down for 15 minutes if you want to operate for more than 3 minutes at a time.
Preset finished or cancelled. Turn the dial to ‘O’ or press ‘Start’ to reselect a preset.
‘—– ‘ shown on screen. Standby mode. Normal operation. Select speed or preset.
‘OPEN’ shown and flashing on screen. Unit beeping. Lid not fitted. Fit lid and press ‘Start’.
Lid removed or open during processing.
‘JUG’ shown and flashing on screen. Unit beeping. Goblet not fitted. Fit goblet and press ‘Start’.
Goblet removed during processing.
Error Codes
E0 – E5 shown on screen and unit beeps.
Heater or motor overload/overheat issues. (Thermal cut out operated). Unplug and wait a few seconds until the screen goes blank.
Then plug back in to reset. Before restarting check that sufficient liquid is being used.
Insufficient liquid in recipe and goblet has boiled dry.
Goblet overloaded.
Check that sufficient liquid added.
Follow the advice in this manual and reduce processing quantities if exceeding the recommendations.
If the problem persists contact your nearest authorised Kenwood Service Centre. To find up to date details of your nearest Kenwood Service Centre visit www.kenwoodworld.com or the website specific to your country.

Kenwood Ltd
New Lane
Havant
Hampshire
PO9 2NH
kenwoodworld.com
© Copyright 2021 Kenwood Limited. All rights reserved