HP 9TL96-90004 Latex Plus Cutter Instruction Manual

hp 9TL96-90004 Latex Plus Cutter Instruction Manual

In-box content list

  • Cutter body
  • Stand
  • HP standard holder
  • HP standard blades (x2)
  • HP cut-off knife
  • HP 3-in media flanges
  • Power cord
  • Software RIP card
  • Setup poster
  • Introduction guide document

Please read these instructions carefully. These assembly instructions explain how to assemble the cutter. Notice that the icons used in this document are also located on the cutter packaging. The icons help you locate the parts needed at each stage of the assembly. Because spare screws are supplied, some screws will remain unused after assembly of the cutter.

The space required for assembly is 3m (10ft feet) in front and 1m (3,3ft feet) at the back.

2 people are required to perform certain tasks

Time required for assembly of the cutter is approximately 60 minutes.

Note: Depending on your LAN installation, a web proxy server name and port may be required to complete the installation of this cutter. Contact your IT manager to get connectivity settings.

Unpacking

Find a flat surface to place the cutter body on, a table is recommended.

Remove the end caps and plastic bag. Be careful with the end caps, the cutter hubs are stored inside them.

Remove the cutter body from the box and place it on the flat surface.
IMPORTANT: 2 people are required.

See an installation video here:

www.hp.com/go/plusprintandcutter/stand_assembly

The stand parts are at the bottom of the box (1), and the accessories are in a box attached to the side (2)..

The stand box includes the basket (1) and the stand (2).
Important: Only use the cutter with the model specific stand included.

Assemble the cutter

Remove the stand parts from the box.
Note: Leave the basket for later.

Identify the screws

Identify the tools.

Insert 2 M5x18 screws and washers at the bottom of the horizontal panels (left and right), and screw them in 7 to 8 turns.

Insert the horizontal beam into slots in the legs.

Firmly insert 2 M5x18 screws and washers just above the two screws that are in the slots at each side.

Turn the stand upside down
Important: 2 people are required.

Push the 4 wheels into the feet.

Mount both feet to the legs with a clamp plate and 4 M5x60 screws and washers each side. Use the 4mm hex key.

Turn the stand upright.
Important: 2 people are required.


Place the stand next to the cutter and lock the wheels.

Locate the left and right positioning pins to place the cutter on the stand.

Place the cutter on the stand, and make sure it is correctly positioned on the pins.
Important: 2 people are required.

Fix the cutter to the stand with two M5x10 screws each side. Use the 3 mm. tool.

Optional: Take the power cord and the LAN or USB cable and mark them at 26-28 cm from the end.

Optional: The right-hand side, fix the cable to the stand with 4 cable ties. Align the marks on the cables with the top cable tie.

If you did not route the cables, you can insert the small covers.

Guide the cables through the slots in the side cover and fix with 4 PT5x10 screws. Use the TX20 tool.

Insert another set of small covers, then mount the cover at the other side of the stand and fix with 4 PT5x10 screws. Use the TX20 tool.

Mount the left and right roll support brackets and fix with 4 M5x10 screws each side. Use the 3 mm tool. Rotate the left and right plates.

Put a cap at each end of the tubes.

Slide the two guiding bushes and the brake over a roll as shown. Check the parts are well positioned.

Put the 2 rolls onto the roll support brackets. Make sure the brake is correctly positioned.

Locate the basket parts.

Unroll the basket and put it in the floor.

Insert the long straight tube into the middle loop of the basket.

Insert the L tubes through the end loops and across the basket at both ends.

Pass the basket between the printer and the stand.

Remove the stopper from the long straight tube. Insert the tube into the slots on the legs. Install the stopper into the tube again to fix it to the leg.

Insert the 4 small tubes.

Insert the 4 small tubes into the slots on feet.

The basket is now assemble

Setting up the cutter

Unlock the wheels and move the cutter to its final location.

Important: If the knife is not installed, take it from the accessory box and install it. If the knife is inserted in the holder, extract it to use the cutter. See the user guide for information on how to use the cutter.

Install the LAN cable and power cables at the back of the cutter and plug them in.

Switch the cutter on.

The front panel prompts you to select a language and follow the first configuration steps.

Your HP FlexiPrint and Cut RIP license is included, go to: www.saicloud.com to download it using the activation code written on the card provided.
FlixPRINT & CUT/ HP Standard Series Edition
www.saicloud.com
www.saicloud.com/howtoinstall

© Copyright 2021 Hewlett-Packard Development Company, L.P.

The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.