D-Link BAX1230P Access Point Installation Guide

D-Link BAX1230P Access Point

Before You Begin

This installation guide provides instructions for installing the DBA-X1230P on your network. Additional documentation is also available on the D-Link support website.

• D-Link Nuclias User Manual: For additional information and instructions on how to configure the device using the D-Link Nuclias Cloud.
• DBA-X1230P User Manual: For additional information and instructions on how to configure the device using the web user interface.

Package Contents

This DBA-X1230P package should include the following items:

• 1 x DBA-X1230P
• 1 x Power adapter (optional)*
• 1 x Mounting kit

If any of the above items are damaged or missing, please contact your local D-Link reseller.
*If the power adapter is not included, it can be purchased separately. Please contact your local D-Link reseller.

Setup Preparation

Please ensure that the following items are readily available before continuing the installation process:

• An active D-Link Nuclias account.
• An active Internet connection to connect to the D- Link Nuclias cloud.
• A valid device license. Contact your D-Link Nuclias service provider for more information.

System Requirements

• A PC or laptop with a working Ethernet adapter or wireless interface.
• Mozilla Firefox 52.0 or higher, Internet Explorer 11 or higher, Safari 10.1 or higher, Google Chrome 59 or higher.
• OS X 10.8.5, Windows 7, Linux (Ubuntu 12).

Hardware Overview

LED Indicators

Figure 1: Front Panel LED

Interface Connectors

Figure 2: Rear Connectors

Powering the Access Point
The DBA-X1230P can be powered using one of the following two methods:

Using Power over Ethernet (PoE)
Use a standard Ethernet cable to connect the LAN port on the DBA-X1230P to a PoE power source device such as a PoE switch or PoE injector.

(Optional) Using the Power Adapter
Connect the power connector of the adapter to the power input on the DBA-X1230P and plug the adapter into a nearby power outlet.

Configuring the Access Point

Using D-Link Nuclias
Note: To use D-Link Nuclias, the DBA-X1230P must be connected to the Internet.
The DBA-X1230P is designed to be managed through the D-Link Nuclias cloud. Refer to the D-Link Nuclias User Manual for detailed configuration instructions.

Figure 3: Connecting through D-Link Nuclias

1. On an Internet-connected PC, open a web browser and go to www.nuclias.com.
2. Enter your D-Link Nuclias user name and password.

If a device’s login credentials are modified using Nuclias Cloud, the local username and password will also reflect the changes made. To learn more about configuring your password, please refer to the Nuclias Cloud manual.

Manual Configuration
Note: D-Link recommends manually configuring the device before mounting it. If you are unable to connect to the D-Link Nuclias cloud, you may need to manually configure the DBA-X1230P using its web user interface (UI).  Refer to the DBA-X1230P User Manual for detailed configuration instructions. Use one of the following methods to access the web user interface:

Connecting through Ethernet
Note: The management PC must be in the same subnet as the DBA-X1230P.

1. Use an Ethernet cable to connect the DBA-X1230P to the management PC or to the switch or router the management PC is connected to.
2. Open a web browser and type in the default host name of the DBA-X1230P and press Enter. The default host name is DBA-X1230P-XXXX where XXXX represents the last 4 characters of the MAC address listed on the device label located on the bottom of the device.
3. When prompted, enter the default login credentials:
   • User name: admin
   • Password: admin

Connecting Wirelessly

1. Connect the management PC to the default SSID of the DBA-X1230P. The SSID will be in the format DBA-X1230P-XXX where XXXX represents the last 4 characters of the MAC address listed on the device label located on the bottom of the device.
2. Open a web browser and type in the default host name of the DBA-X1230P and press Enter. The default host name is DBA-X1230P-XXXX where XXXX represents the last 4 characters of the MAC address listed on the device label located on the bottom of the device.
3. When prompted, enter the default login credentials:
   • User name: admin
   • Password: admin

Attaching the Rubber Pads

The included rubber pads can be placed on the bottom of the device to prevent the device from damaging the surface it is placed on.

1. Remove the rubber pads from the adhesive strip.
2. Stick one pad on each foot on the bottom panel of the access point.

Mounting on a Solid Wall or Ceiling

1. (Optional) Attach the included lock plate to the mounting plate using the included screws.
2. Use the mounting plate to mark the location where to drill the holes in the wall or ceiling.
3. Drill holes on the markings and place the included anchors into the drilled holes.
4. Align and place the mounting plate on top of the anchors and use the included screws to secure the mounting plate to the surface.
5. Connect the Ethernet cable and power adapter (optional) to the device.
6. 6. Slide the DBA-X1230P onto the mounting plate.

Mounting on a Ceiling Crossbar

1. (Optional) Attach the included lock plate to the mounting plate using the included screws.
2. Clip the two included ceiling brackets onto the ceiling crossbar. Make sure both brackets are positioned in line with each other.
3. Using the included screws, secure the mounting plate to the ceiling brackets..
4. Connect the Ethernet cable and power adapter (optional) to the device.
5. Slide the DBA-X1230P onto the mounting plate.

Locking the DBA-X1230P

If the lock plate was attached, insert a lock through the device’s lock slot to secure the DBA-X1230P to the mounting plate.

• Press and hold down the reset button between  6 to 15 seconds and release to reset the device to its factory default settings.
• Press and hold down the reset button for  more than 15 seconds and release to reset the device to its factory default settings and force the device to load an alternate firmware.

Troubleshooting

The DBA-X1230P receives its configuration settings and is managed through the D-Link Nuclias cloud. If you are experiencing problems connecting to the D-Link Nuclias cloud, check your Internet connection. If you still cannot connect to the service, additional configuration on the device may be required. Refer to the DBA-X1230P User Nuclias Cloud Manual for detailed information on how to manually configure the device.

Additional Information
For additional support, please refer to the user manual, or visit your local D-Link support website.
Warning: The DBA-X1230P is designed to receive PoE power only from an 802.3at compliant source, or from a D-Link-approved power adapter. Connecting an access point to a Power over Ethernet (PoE) device that is not approved by D-Link can damage the equipment.

Appendix – Statements

ErP Power Usage
This device is an Energy Related Product (ErP) that automatically switches to a power-saving Network Standby mode within 1 minute of no packets being transmitted. It can also be turned off through a power switch to save energy when it is not needed.

• Network Standby: 7.27 watts
• Switched Off: 0.06 watts

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Non-modifications Statement:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.

Note
The country code selection is for non-USA models only and is not available to all USA models. Per FCC regulations, all WiFi product marketed in the USA must be fixed to USA operational channels only.

RF Frequency Requirements
This device is for indoor use only when using all channels in the 5.15 to 5.25 GHz frequency range. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device. This device will not operate on channels which overlap the 5600-5650 MHz band. It is restricted to indoor environments only

IMPORTANT NOTICE:

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 23.7cm between the radiator and your body.

Innovation, Science and Economic Development Canada (ISED) Statement:
This Class B digital apparatus complies with Canadian ICES-003.
C

Innovation, Science and Economic Development Canada (ISED) Statement:
This device complies with ISED licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

Radiation Exposure Statement
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 26.6cm between the radiator and your body.

Japan Voluntary Control Council for Interference Statement
This is a Class B product based on the standard of the VCCI Council. If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.

Product and Warranty Information

To find out more about D-Link products or marketing information, please visit the website http://www.dlink.com.
The D-Link Limited Lifetime Warranty information is available at http://warranty.dlink.com/