Bosch DWB65BC50I Wall-Mounted Extractor Hood User Manual

BOSCH DWB65BC50I Wall-Mounted Extractor Hood

Safety

Observe the following safety instructions.

General information

Read this instruction manual carefully.
Keep the instruction manual and the product information safe for future refer- ence or for the next owner.
Do not connect the appliance if it has been damaged in transit.

Intended use

This appliance is designed only to be built into kitchen units. Read the special installation instructions.
The appliance can only be used safely if it is correctly installed according to the safety in-structions. The installer is responsible for en-suring that the appliance works perfectly at its installation location.

Only use this appliance:

For extracting cooking vapour.
In private households and in enclosed spaces in a domestic environment.
Up to an altitude of max. 2000 m above sea level.

Do not use the appliance With an external timer.

Restriction on user group
This appliance may be used by children aged 8 or over and by people who have reduced physical, sensory or mental abilities or inad-equate experience and/or knowledge, provided that they are supervised or have been instructed on how to use the appliance safely and have understood the resulting dangers.
Do not let children play with the appliance. Children must not perform cleaning or user maintenance unless they are at least 15 years old and are being supervised.
Keep children under the age of 8 years away from the appliance and power cable.

Safe use
WARNING ‒ Risk of suffocation!Children may put packaging material over their heads or wrap themselves up in it and suffocate.

Keep packaging material away from children.
Do not let children play with packaging material.

Children may breathe in or swallow small parts, causing them to suffocate.

Keep small parts away from children.
Do not let children play with small parts.

WARNING ‒ Risk of poisoning

Risk of poisoning from flue gases being drawn back in. Room-air-dependent heat-pro-ducing appliances (e.g. gas, oil, wood or coal-operated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and dis-charge the exhaust gases into the open through an exhaust gas system (e.g. a chim-ney). With the extractor hood switched on, air is extracted from the kitchen and the adjacent rooms. Without an adequate supply of air, the air pressure falls below atmospheric pressure.
Toxic gases from the flue or the extraction shaft are sucked back into the living space.

Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as a room-air-dependent heat-producing appli-ance is being operated.
It is only possible to safely operate the ap-pliance if the pressure in the room in which the heating appliance is installed does not drop more than 4 Pa (0.04 mbar) below at-mospheric pressure. This can be achieved whenever the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/exhaust air wall boxes or by other technical means. An incoming/ex-haust air wall box alone does not ensure compliance with the limit.
In any case, consult your responsible chim-ney sweep. They are able to assess the house’s entire ventilation setup and will suggest the suitable ventilation measures to you.
Unrestricted operation is possible if the ap-pliance is operated exclusively in circulat-ing-air mode.

WARNING ‒ Risk of fire
Fatty deposits in the grease filters may catch fire.

Never operate the appliance without a grease filter.
Clean the grease filters regularly.
Never work with naked flames close to the appliance (e.g. flambéing).
Do not install the appliance near a solid fuel heating appliance (e.g. wood- or coal-burning) unless the heating appliance has a sealed, non-removable cover. There must be no flying sparks.
Hot oil or grease ignites very quickly.
Always supervise hot oil and fat.
Never extinguish burning oil or fat with wa-ter. Switch off the cooking zone. Extinguish flames carefully using a lid, fire blanket or something similar.
When gas burners are in operation without any cookware placed on them, they can build up a lot of heat. A ventilation appliance in-stalled above the cooker may become dam-aged or catch fire.
Only operate the gas burners with cook-ware on them.
Operating multiple gas hobs at the same time generates a great deal of heat. A ventilation appliance installed above the cooker may be-come damaged or catch fire.
Only operate the gas hobs with cookware on them.
Select the highest fan setting.
Never operate two gas hobs simultan-eously on the highest flame for longer than 15 minutes. Two gas hobs correspond to one large burner.
Never operate large burners of more than 5 kW with the highest flame for longer than 15 minutes, e.g. a wok.

WARNING ‒ Risk of burns
The accessible parts of the appliance become hot during operation.

Never touch these hot parts.
Keep children at a safe distance.
The appliance becomes hot during operation.
Allow the appliance to cool down before cleaning.

WARNING ‒ Risk of injury!
Components inside the appliance may have sharp edges.

Carefully clean the appliance interior. Items placed on the appliance may fall off.
Do not place any objects on the appliance. Changes to the electrical or mechanical as-sembly are dangerous and may lead to mal-functions.
Do not make any changes to the electrical or mechanical assembly.
The filter cover may swing out.
Open the filter cover slowly.
Take hold of the filter cover after opening until it no longer swings out.
Close the filter cover slowly.

Avoiding material damage

The light emitted by LED lights is very dazzling, and can damage the eyes (risk group 1). Do not look directly into the switched-on LED lights for longer than 100 seconds.
WARNING ‒ Risk of electric shock!An ingress of moisture can cause an electric shock.
Do not use steam- or high-pressure clean-ers to clean the appliance.
WARNING ‒ Risk of explosion
Highly caustic alkaline or highly acidic clean-ing agents in conjunction with aluminium parts in the interior of the appliance may cause ex-plosions.
Never use highly caustic alkaline or highly acidic cleaning agents. In particular, do not use commercial or industrial cleaning agents in conjunction with aluminium parts,
e. g. grease filter on extractor hoods.

Avoiding material damage

ATTENTION!
Condensate may cause corrosion damage.

To prevent condensation from building up, switch on the appliance during cooking.
If moisture gets into the controls, this may result in damage.
Never clean controls with a wet cloth. Incorrect cleaning damages the surfaces.
Follow the cleaning instructions.
Do not use harsh or abrasive detergents.
Clean stainless steel surfaces in the direction of the finish only.
Never clean controls with stainless steel cleaners. Condensation that flows back in may damage the ap-pliance.
The air extraction duct must be installed with a gradient of at least 1° from the appliance.
If you put incorrect stress on the design elements, they may break off.
Do not pull design elements.
Do not place objects on the design elements or hang objects from them.
There is a risk of surface damage if you do not peel off the protective film.
Remove the protective film from all parts of the ap-pliance before using for the first time.
If one lamp is defective, this may overload the remain-ing lamps.
Replace any defective lamps. Painted surfaces are easily damaged.
Follow the cleaning instructions. → “Cleaning the appliance”, Page 6
Ensure that the painted surfaces are not scratched.

Environmental protection and saving energy

Disposing of packaging
The packaging materials are environmentally compat-ible and can be recycled.

Sort the individual components by type and dispose of them separately.

Saving energy
If you follow these instructions, your appliance will use less power. Adjust the fan speed to the amount of steam pro-duced during cooking. ¡The lower the fan speed, the less energy is con- sumed.

If cooking produces large amounts of steam, select a higher fan speed in good time.

The odours are distributed around the room less.
Switch off the lighting if it is no longer required.
When the lighting is switched off, it does not con-sume any energy.
Clean or replace the filters at regular intervals.
The effectiveness of the filter is retained. Put the cooking lid on.
The cooking vapours and condensation are re- duced.
Only use the additional functions if required.
Switching off additional functions reduces power consumption.

Operating modes

You can use your appliance in air extraction mode or circulating-air mode.
Air extraction mode
The air which is drawn in is cleaned by the grease fil-ters and conveyed to the exterior by a pipe system.
The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).

If the exhaust air is to be conveyed into a non-functioning smoke or ex-haust gas flue, you must obtain the consent of the heating engineer re-sponsible.
If the exhaust air is conveyed through the external wall, a tele-scopic duct should be used.

Air recirculation mode
The air which is drawn in is cleaned by the grease fil-ters and an odour filter, and conveyed back into the room.

To bind odours in circulating-air mode, you must install an odour filter. The dif-ferent options for operating the appli-ance in circulating-air mode can be found in our catalogue. Alternatively, ask your dealer. The required accessor-ies are available from specialist retail-ers, from customer service or from the Online Shop.

Familiarising yourself with your appliance

Controls
The controls are used to configure all functions of your appliance and to obtain information about the operat-ing status.

Accessories

You can buy accessories from the after-sales service, from specialist retailers or online. Only use original ac-cessories, as these have been specifically designed for your appliance.
“Accessories vary from one appliance to another. When purchasing accessories, always quote the exact product number (E no.) of your appliance.”

You can find out which accessories are available for your appliance in our catalogue, in the online shop or from our after-sales service.
www.bosch-home.com

Accessories Order number
Standard odor filter DHZ5377

Basic operation

Switching on the appliance
Press The appliance starts at fan setting 1.

Selecting a fan setting
Press or to adjust the fan setting.

Switching off the appliance
Press ⁠

Switching on the lighting
The lighting can be switched on and off independently of the ventilation system. Press ⁠.

Switching off the lighting
Press

Cleaning and servicing

To keep your appliance working efficiently for a long time, it is important to clean and maintain it carefully.

Cleaning products
You can obtain suitable cleaning products from after-sales service or the online shop.

ATTENTION
Unsuitable cleaning products may damage the sur-faces of the appliance.

Do not use harsh or abrasive detergents.
Do not use cleaning products with a high alcohol content.
Do not use hard scouring pads or cleaning sponges.
Do not use any special cleaners for cleaning the ap-pliance while it is hot.
Only use glass cleaners, glass scrapers or stainless steel care products if recommended in the cleaning instructions for the relevant part.
Wash sponge cloths thoroughly before use.

Cleaning the appliance
Clean the appliance as specified. This will ensure that the different parts and surfaces of the appliance are not damaged by incorrect cleaning or unsuitable clean-ing products.

WARNING ‒ Risk of explosion
Highly caustic alkaline or highly acidic cleaning agents in conjunction with aluminium parts in the interior of the appliance may cause explosions.
Never use highly caustic alkaline or highly acidic cleaning agents. In particular, do not use commer-cial or industrial cleaning agents in conjunction with aluminium parts, e.g. grease filter on extractor hoods.

WARNING ‒ Risk of electric shock
Ingress of moisture can cause an electric shock.

Before cleaning, pull out the mains plug or switch off the fuse in the fuse box.
Do not use steam- or high-pressure cleaners to clean the appliance.

WARNING ‒ Risk of burns
The appliance will become hot during operation.
Allow the appliance to cool down before cleaning it.

WARNING ‒ Risk of injury

Components inside the appliance may have sharp edges.
Carefully clean the appliance interior.

Observe the information regarding the cleaning agents.
Clean as follows, depending on the surface:
- Clean stainless steel surfaces in the direction of the finish using a sponge cloth and hot soapy water.
- Clean painted surfaces using a damp sponge cloth and hot soapy water.
- Clean aluminium using a soft cloth and glass cleaner.
- Clean plastic using a soft cloth and glass cleaner.
- Clean glass using a soft cloth and glass cleaner.
Dry with a soft cloth.
Apply a thin layer of the stainless steel cleaning product to stainless steel surfaces using a soft cloth.
You can obtain stainless steel cleaning products from the after-sales service or the online shop.

Cleaning controls
WARNING ‒ Risk of electric shock!
Penetrating moisture may cause an electric shock.
Do not use wet sponge cloths.

Observe the information regarding the cleaning agents.
Clean using a damp sponge cloth and hot soapy water.
Dry with a soft cloth.

Removing the grease filter

ATTENTION!
Falling grease filters may damage the hob below.

Grip below the grease filter with one hand.
Open the locks on the grease filters.
Remove the grease filters from the holders.To prevent grease from dripping, hold the grease fil-ter horizontally.

Cleaning grease filters manually
The grease filters filter the grease from the cooking va-pour. Regularly cleaned grease filters guarantee a high level of grease removal.
WARNING ‒ Risk of fire
Fatty deposits in the grease filters may catch fire.
Clean the grease filters roughly every 2 months. Requirement: The grease filters have been removed.

Observe the information regarding the cleaning agents.
Soak the grease filter in hot soapy water.
Use special grease solvent for stubborn dirt. You can obtain grease solvents from after-sales service or the online shop.
Use a brush to clean the grease filters.
Rinse the grease filters thoroughly.
Allow the grease filters to drain.

Cleaning grease filters in the
dishwasher
The grease filters filter the grease from the cooking vapors. Regularly cleaned grease filters guarantee a high level of grease removal.
WARNING ‒ Risk of fire
Fatty deposits in the grease filters may catch fire. Clean the grease filters roughly every 2 months.

ATTENTION
The grease filters may become damaged if they are squeezed.
Do not squeeze the grease filters.

Note: When cleaning the grease filter in the dishwasher, light discoloration may occur. This discoloration has no effect on the performance of the metal grease filters.
Requirement: The grease filters have been removed.

Observe the information regarding the cleaning agents.
Place the grease filters loosely into the dishwasher. Do not clean heavily soiled grease filters with utensils.
Use special grease solvent for stubborn dirt. You can obtain grease solvents from after-sales service or the online shop.
Start the dishwasher. Select a temperature of no more than 70 °C.
Allow the grease filters to drain.

Fitting grease filters
ATTENTION
Falling grease filters may damage the hob below.
Grip below the grease filter with one hand.

Fit the grease filters.
Fold the grease filters upwards and engage the locks.
Make sure that the locks engage.
Close the filter cover.

Odor filter for recirculating air mode
Odor filters bind odorous substances in air recircula-tion mode. Regularly replaced odour filters guarantee a high level of odour removal. With normal use (approx. one hour a day), the odour fil-ter must be replaced every 3-5 months. The odour fil-ter cannot be cleaned or regenerated. You can obtain odour filters from the after-sales service or the online shop. Only use original odour filters.
Removing odour filter
Requirement: The grease filters have been removed.

Press and hold the lock for the odour filter.
Remove the odor filter.
1. First, insert the odour filter, rear first, into the hous- ing.
2. Press and hold the lock until the odour filter is fully inserted into the housing.
3. → “Fitting grease filters”, Page 8

Troubleshooting

You can rectify minor faults on your appliance yourself. Read the troubleshooting information before contacting after-sales service. This will avoid unnecessary costs.
WARNING ‒ Risk of injury!Improper repairs are dangerous.

Repairs to the appliance should only be carried out by trained specialist staff.
If the appliance is defective, call Customer Service.

WARNING ‒ Risk of electric shock!
Incorrect repairs are dangerous.

Repairs to the appliance should only be carried out by trained specialist staff.
Only use genuine spare parts when repairing the appliance.
If the power cord of this appliance is damaged, it must be replaced by trained specialist staff.

Malfunctions

Fault Cause and troubleshooting
The appliance is not working. The mains plug of the power cord is not plugged in.
Connect the appliance to the power supply.
The circuit breaker is faulty.
Check the circuit breaker in the fuse box.
There has been a power cut.
Check whether the lighting in your kitchen or other appliances are working.

The LED lighting does not work. The LED lamp is defective.
→ “Replacing the LED lights”, Page 9

Replacing the LED lights

WARNING ‒ Risk of electric shock!
When changing the bulb, the bulb socket contacts are live.
Before replacing the bulb, unplug the appliance from the mains or switch off the circuit breaker in the fuse box.

WARNING ‒ Risk of injury!
The light emitted by LED lights is very dazzling, and can damage the eyes (risk group 1).

Do not look directly into the switched-on LED lights for longer than 100 seconds.
Note:
Only use bulbs of the same type and wattage.
Remove the grease filters.
→ “Removing the grease filter”, Page 7
Push the lamp out of the appliance from the rear.
Turn the lamp a quarter turn anti-clockwise and re-move it.
Replace the lamp with one of the same type.
Install the grease filters.
Insert the mains plug and switch on the fuse again.

Disposal

Find out here how to dispose of old appliances cor-rectly.
Disposing of old appliance
Valuable raw materials can be reused by recycling.
Dispose of the appliance in an environmentally friendly manner.
Information about current disposal methods are available from your specialist dealer or local author-ity.
This appliance is labelled in accord-ance with European Directive 2012/19/EU concerning used elec-trical and electronic appliances (waste electrical and electronic equip-ment – WEEE). The guideline determines the frame-work for the return and recycling of used appliances as applicable throughout the EU.

Customer Service

If you have any queries on use, are unable to rectify faults on the appliance yourself or if your appliance needs to be repaired, contact Customer Service. Detailed information on the warranty period and terms of warranty in your country is available from our after-sales service, your retailer or on our website. If you contact Customer Service, you will require the product number (E-Nr.) and the production number (FD) of your appliance. The contact details for Customer Service can be found in the enclosed Customer Service directory or on our website.
Product number (E-Nr.) and production number (FD)
You can find the product number (E-Nr.) and the pro-duction number (FD) on the appliance’s rating plate. Depending on the model, the rating plate can be found:

Inside the appliance (remove grease filters for ac- cess).
On top of the appliance.

Make a note of your appliance’s details and the Cus-tomer Service telephone number to find them again quickly.

Installation instructions

Observe this information when installing the appliance.

Scope of delivery
After unpacking all parts, check for any damage in transit and completeness of the delivery.

Appliance dimensions
You will find the dimensions of the appliance here

Safety clearances
Comply with the safety clearances for the appliance.

For Australia and New Zealand the minimum safety clearance above electrical cooktops must be 600 mm.
Secure installation
Follow these safety instructions when in-stalling the appliance.

WARNING ‒ Risk of poisoning
Risk of poisoning from flue gases being drawn back in. Room-air-dependent heat-pro-ducing appliances (e.g. gas, oil, wood or coal-operated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and dis-charge the exhaust gases into the open through an exhaust gas system (e.g. a chim-ney). With the extractor hood switched on, air is extracted from the kitchen and the adjacent rooms. Without an adequate supply of air, the air pressure falls below atmospheric pressure. Toxic gases from the flue or the extraction shaft are sucked back into the living space.

Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as a room-air-dependent heat-producing appli-ance is being operated.
It is only possible to safely operate the ap-pliance if the pressure in the room in which the heating appliance is installed does not drop more than 4 Pa (0.04 mbar) below at-mospheric pressure. This can be achieved whenever the air needed for combustion is able to enter through openings that cannot be sealed, for example in doors, windows, incoming/exhaust air wall boxes or by other technical means. An incoming/ex-haust air wall box alone does not ensure compliance with the limit.
In any case, consult your responsible chim-ney sweep. They are able to assess the house’s entire ventilation setup and will suggest the suitable ventilation measures to you.
Unrestricted operation is possible if the ap-pliance is operated exclusively in circulat-ing-air mode.
Risk of poisoning from flue gases being drawn back in.
If an extractor hood with an open-flued heat production source is installed, the power supply for the extractor hood must be provided with a suitable safety switch.
Risk of poisoning from flue gases being drawn back in.
Do not emit the exhaust air into a smoke or exhaust gas flue that is in operation.
Do not emit the exhaust air into a shaft that is used to ventilate installation rooms for heat-producing appliances.
If the exhaust air is to be conveyed into a smoke or exhaust gas flue, you must obtain the consent of the heating engineer re-sponsible.
WARNING ‒ Risk of suffocation! Children may put packaging material over their heads or wrap themselves up in it and suffocate.
Keep packaging material away from chil-dren.
Do not let children play with packaging ma-terial.
WARNING ‒ Risk of fire!
Grease deposits in the grease filter may catch fire.
The specified safety clearances must be complied with in order to prevent a build-up of heat.
Observe the specifications for your cooking appliances. If the installation instructions for the cooking appliances specify a different clearance, the larger of the two must al-ways be provided for. If gas hobs and elec-tric hobs are operated together, the largest specified clearance applies.
The appliance must be installed with no more than one side directly next to a high-sided unit or a wall. The distance between the appliance and wall or high-sided unit must be at least 50 mm.
The grease deposits in the grease filter may catch fire.
Never work with naked flames close to the appliance (e.g. flambéing).
Do not install the appliance near a heat-producing appliance for solid fuel (e.g. wood or coal) unless a closed, non-remov-able cover is present. There must be no fly-ing sparks.
WARNING ‒ Risk of injury
Components inside the appliance may have sharp edges.
Wear protective gloves.
The appliance may fall down if it has not been properly fastened in place.
All fastening components must be fixed firmly and securely in place. The appliance is heavy.
To move the appliance, two people are re-quired.
Use only suitable tools and equipment. The appliance is heavy.
The appliance must not be fitted directly onto plasterboard or similar lightweight ma-terials.
To ensure correct installation, you must use a material which is sufficiently stable and suitable for both the structural conditions and the weight of the appliance.
Changes to the electrical or mechanical as-sembly are dangerous and may lead to mal-functions.
Do not make any changes to the electrical or mechanical assembly. The filter cover may swing out.
Open the filter cover slowly.
Take hold of the filter cover after opening until it no longer swings out.
Close the filter cover slowly.
WARNING ‒ Risk of electric shock!
Sharp-edged components inside the appli-ance may damage the connecting cable.
Do not kink or trap the connecting cable. Incorrect installation is dangerous.
Connect and operate the appliance only in accordance with the specifications on the rating plate.
Connect the appliance to a power supply with alternating current only via a properly installed socket with earthing.
The protective conductor system of the do-mestic electrical installation must be prop-erly installed.
Never equip the appliance with an external switching device, e.g. a timer or remote control.
When the appliance is installed, the mains plug of the power cord must be freely ac-cessible. If free access is not possible, an all-pole isolating switch must be installed in the permanent electrical installation accord-ing to the conditions of Overvoltage Cat-egory III and according to the installation regulations.
When installing the appliance, check that the power cable is not trapped or dam-aged.

General information
Follow these general instructions during the installation. ¡ For the installation, observe the currently valid build- ing regulations and the regulations of the local elec-tricity and gas suppliers.
When discharging the exhaust air, the official and legal regulations, such as the regional building code., must be observed.¡In order to freely access the appliance for servicing,
select an easy-to-reach installation site. The surfaces of the appliance are sensitive. Avoid damaging them during installation.

Instructions for the electrical connection
In order to safely connect the appliance to the elec-trical system, follow these instructions.

WARNING ‒ Risk of electric shock!
It must always be possible to disconnect the appliance from the electricity supply. The appliance must only be connected to a protective contact socket that has been correctly installed.

The mains plug for the mains power cable must be easily accessible after the appliance is installed.
If this is not possible, an all-pole isolating switch must be integrated into the permanent electrical in-stallation according to the conditions of overvoltage category III and according to the installation regula-tions.
The permanent electrical installation must only be wired by a professional electrician. We recommend installing a residual-current circuit breaker (RCCB) in the appliance’s power supply circuit.
Sharp-edged components inside the appliance may damage the connecting cable.
Do not kink or trap the connecting cable.
The connection data can be found on the rating
The connecting cable is approx. 1.30 m long.
This appliance complies with the EC interference suppression regulations.
The appliance corresponds to protection class 1.
You should therefore only use the appliance with a protective earth connection.
Do not connect the appliance to the power supply during installation.
Ensure that the protection against contact is guaran-teed during installation.

Information on the installation situation

Install this appliance on the kitchen wall.
To install additional special accessory parts, ob- serve the enclosed installation instructions.
The appliance must be installed with no more than one side directly next to a high-sided unit or a wall. The distance between the appliance and wall or high-sided unit must be at least 50 mm.
The width of the extractor hood must correspond at least with the width of the hob.
To optimally detect the cooking vapours, install the appliance in the middle of the hob.

Instructions for the exhaust air pipe
The appliance manufacturer does not provide any war-ranty for faults attributable to the pipeline.

Use a short, straight exhaust air pipe with as large a pipe diameter as possible.
Long, rough exhaust air pipes, many pipe bends or small pipe diameters reduce the suction power and increase the fan noise.
Use an exhaust pipe that is made of non-combust- ible material.
To prevent condensate from returning, fit the ex- haust pipe with a 1° gradient from the appliance. Flat ducts
Use flat ducts with an inner cross-section that corres-ponds to the diameter of the round pipes:
Diameter of 150 mm corresponds to ap- prox. 177 cm².
Diameter of 120 mm corresponds to ap- prox. 113 cm².
Use sealing strips for different pipe diameters.
Do not use any flat ducts with sharp bends. Round pipes
Use round pipes with an inner diameter of 150 mm (re-commended) or at least 120 mm.\

Instructions for the air extraction mode
For air extraction mode, a one-way flap should be in-stalled.
Notes

If a one-way flap is not included with the appliance, one can be ordered from a specialist retailer.
If the exhaust air is conveyed through the external

Information about circulating-air mode
The appliance must only be operated when it is se-curely installed and the pipework is connected.
Installation
Checking the wall

Check whether the wall is vertical and has sufficient load-bearing capacity. The max. weight of the appliance is 14 kg.
Drill the hole depth in accordance with the length of the screws.
The wall plugs must have a secure grip.
The enclosed screws and wall plugs are suitable for solid brickwork, plasterboard, porous concrete and poroton bricks.
Ensure that there are no electrical wires, gas pipes or water pipes in the area where holes are to be drilled.
Cover the hob to prevent damage.
Mark a vertical centre line on the wall from the ceil-ing to the lower edge of the appliance.
Mark the holes for the flue connection plate. The centre of the flue connection plate is marked with a notch.
Place the plate in the centre of the centre line and align it horizontally.
Mark the positions of the holes.
Mark the holes for the appliance bracket.
Drill the holes.
Insert the wall plugs flush with the wall.
Screw in the flue connection plate.
Screw in the screws for the appliance bracket so that there is a clearance of 5 mm between the screw head and the wall.
Preparing the appliance
Open the filter cover if required.
Remove the grease filters.To avoid causing damage, do not bend the grease filters.
Installing the appliance
WARNING ‒ Risk of injury!
Components inside the appliance may have sharp edges.
Wear protective gloves.|
1. Remove the protective film from the rear. Once the appliance is installed, fully remove the protective film.
2. Screw the product mounting plates with washer onto the appliance.
3. Attach the appliance.
4. Align the appliance horizontally.
  Loosen and tighten the M5 x 35 screws to align the appliance.
5. Tighten the screws for the appliance bracket.
6. Secure the appliance.
7. Remove the protective film from the grease filters.
8. Fit the grease filters.

To avoid causing damage, do not bend the grease filters

Establishing the exhaust air connection 1. Screw the air outlet onto the housing.
If required, fit the flue adapter onto the air outlet and press firmly.
Secure the exhaust pipe to the air pipe connector.
Establish the connection to the exhaust air opening.
Seal the joints. Connecting to the power supply

Removing the appliance

Disconnect the appliance from the power supply.
Remove the flue duct.
Loosen the exhaust pipe.
Remove the grease filters. To avoid causing damage, do not bend the grease filters.
Loosen the screws for the appliance bracket slightly but do not undo them fully.
Remove the appliance.
Remove the flue connection plate.

Expert tips & tricks for your appliance
Warranty extension options
Discounts for accessories & spare-parts
Digital manual and all appliance data at hand
Easy access to Bosch Home Appliances Service

Free and easy registration – also on mobile phones: www.bosch-home.com/welcome

Looking for help? You’ll find it here.

Expert advice for your Bosch home appliances, help with problems or a repair from Bosch experts.
Find out everything about the many ways Bosch can support you: www.bosch-home.com/service
Contact data of all countries are listed in the attached service directory.
Robert Bosch Hausgeräte GmbH
Carl-Wery-Straße 34
81739 München
GERMANYwww.bosch-home.com
*9001715246*

Download

Bosch DWB65BC50I Wall-Mounted Extractor Hood User Manual

Was this manual helpful?