SEALEY PFT12 On-Vehicle Micro Pipe Flaring Tool Instruction Manual

InSTRUcTIonS FoR:
ON-VEHICLE MICRO PIPE FLARING
TOOL
MoDEL no: PFT12

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will if used according to these instructions and properly maintained, give you years of trouble free performance.

Warning iconIMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE, FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY INSTRUCTIONS

  • WARNING! Ensure Health & Safety, local authority, and general workshop practice requirements are adhered to when using this equipment. Familiarise yourself with the
    application and limitations, as well as the potential hazards of the set.
  • This set is suitable for steel pipe.
  • Maintain the set in good condition.
  • Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
  • Locate the flaring set in a suitable work area, keep the area clean and tidy and ensure there is adequate lighting.
  • WARNING! Always wear approved eye or face protection when using the flaring tools.
  • Keep children and unauthorised persons away from the working area.
  • DO NOT use the set for any purpose other than for which it is designed.
  • DO NOT use the set if any parts are damaged or missing as this may cause failure and/or personal injury.
  • DO NOT allow untrained persons to use the set.
  • DO NOT attempt to flare piping when you are tired, under the influence of alcohol, drugs, or intoxicating medication.
  • When not in use clean set components, replace in case, and store in a safe, dry, childproof area. Remember! The safe operation of a vehicle, or other equipment, may well depend on the quality of the flare produced. Discard any flare which is misformed.
  • WARNING! The warnings, cautions, and instructions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood that common sense and caution are factors that cannot be built into this product but must be applied by the operator.

INTRODUCTION & SPECIFICATIONS

This design produces accurate automotive SAE flares on 3/16” pipes. A lightweight body makes it ideal for splicing in replacement sections of brake pipe on-vehicle. Suitable for steel pipes. Supplied in carry-case.

OPERATING INSTRUCTIONS

  •  WARNING! Ensure you are familiar with the various types of flare before using this equipment.
  • WARNING! Before using the flaring kit, ensure that you have read and understood the ‘Safety Instructions’ in Section 1.
    3.1 PREPARATIon oF THE BRAKE PIPE
    3.1.1 The end of the pipe must be cut square.
    3.1.2 The outside edge of the pipe must be chamfered to approximately 0.25mm x 45º.
    3.1.3 Important!
    If the pipe is plastic covered, this must be cut back for 6mm from the end of the pipe to be flared. Ensure the pipe is not scored or any metal removed during this operation. DO NOT use an abrasive cloth.
    3.1.4 Important!
    If the pipe is painted it is recommended that the paint be removed for the length of the die by a chemical paint remover, not an abrasive cloth. observe all manufacturers’ precautions when using chemical paint remover. Finally, remove any grease present. These two operations will improve the die jaw grip whilst flaring.
    3.2 cREATIon oF 3/16” SAE SIngLE FLARE
    3.2.1 Use the SAE tool, stop, and double-ended punch as shown in fig.1.
    3.2.2 The stop must be screwed into the tool to within 5mm of the hexagon.
    3.2.3 Slide the tool onto the pipe.
    3.2.4 Tighten the locking screws by hand, just enough to grip the pipe.
    3.2.5 IMPORTANT! DO NOT over-tighten at this stage or the stop will damage the pipe.
    3.2.6 Screw the stop into the tool until fully tightened.
    (A 16mm ratchet spanner is recommended, but not included.)
    3.2.7 Tighten the locking screws fully to clamp the pipe. (A 10mm ratchet spanner is recommended, but not included.)
    IMPORTANT! If the locking screws are not tight enough then the pipe will push back during the flare process and will not produce the correct flare.
    3.2.8 Undo and remove the stop.
    3.2.9 Insert the oP1 end punch and tighten it fully up to the hexagon in order to form the flare.
    3.2.10 Unscrew the punch. The single flare is now complete.
    3.2.11 Undo the locking screws and remove the tool from the pipe.
    3.3 cREATIon oF 3/16” SAE DoUBLE FLARE
    Firstly follow steps 3.2.1 to 3.2.10. to form a single flare.
    3.3.1 Reverse the punch and insert the oP2 end into the tool and fully tighten up to the hexagon in order to form the flare.
    3.3.2 Unscrew the punch.
    3.3.3 Undo the locking screws and remove the tool from the pipe. The double flare is now complete.

NOTE: It is our policy to continually improve products and as such, we reserve the right to alter data, specifications, and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.

Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
01284 757500
01284 703534
www.sealey.co.uk

© Jack Sealey Limited
Original Language Version
PFT12 Issue: 1 – 06/09/12