Husqvarna 9676731-21 Automower 420 Robotic Lawn Mower User Guide


READY WHEN YOU ARE
QUICK GUIDE

HUSQVARNA AUTOMOWER ® 420/430X/440/450X

A Placement of and connecting the charging station

  1.  Place the charging station at a central position in the work area, with a lot of open space in front of the charging station and on a relatively horizontal surface.
  2. Connect the power supply’s low-voltage cable to the charging station and the power supply.
  3. Connect the power supply to a 100-240 V wall socket.
  4. Place the robotic lawnmower in the charging station to charge the battery while the boundary wire is laid. Set the main switch to position 1.

B Placement of the boundary wire and the guide wire

  1.  Lay the boundary wire so that it forms a loop around the working area.
  2. Make an eyelet at the point where the guidewire will later be connected.
  3. Run the guidewire to the point on the boundary loop where the connection will be made. Avoid laying the wire at right angles.

C Connecting the boundary wire and the guide wire

  1. Narrow passages in the yard make it difficult for the robotic lawn mower to find the charging station. The robotic lawn mower can be led to remote areas using the guidewire.
    The guidewire also helps the robotic lawn mower to quickly find the charging station.
  2. Lay the guidewire under the charging station and at least 2 m / 7 ft straight out from the front edge of the charging station.
  3. Open the connectors and lay the wire ends in the recesses on each connector.
  4. Press the connectors together using a pair of pliers.
  5. Cut off any surplus boundary wire. Cut 1-2 cm / 0.4-0.8” above the connectors.
  6. Press the connectors onto the contact pins, marked AL  (left) and AR (right), on the charging station. It is important that the right-hand wire is connected to the right-hand
    contact pin, and the left-hand wire to the left-hand pin.
  7. Fasten the connector to the contact pin marked G1 on the charging station.

D Connecting the guidewire to the boundary wire

  1. Cut the boundary wire with wire cutters at the center of the eyelet that was made in step B.2
  2. Connect the guidewire to the boundary wire using the accompanying couplers. Press the couplers completely together with a polygraph.

Starting and stopping
STARTING

  1. Open the hatch by pressing the STOP button.
  2. Set the main switch to position 1. When you do this for the first time, a start-up sequence starts where you select a four-digit PIN code among other things.
  3. Press the START button and close the hatch.

STOPPING
Press the STOP button.

Adjusting the robotic lawn mower to suit the size of your lawn
The mowing results depend on the mowing time. Adjust the mowing time to suit your yard using the Schedule function. You decide what times during the day the robotic lawn mower is to work.
Use the Weather Timer function and the robotic lawn mower will automatically adjust the mowing time to the growth of the grass.

Maintenance

  • Set the main switch to position 0 to disable the product before all work on the robotic lawn mower’s chassis, such as cleaning or replacing the blades. Replace the blades regularly for the best mowing result.
  • Never use a high-pressure washer or running water to clean the robotic lawnmower. Never use solvents for cleaning. Clean the product with a brush.
  • All connections to the charging station (power supply, boundary, and guidewire) must be disconnected if there is a risk of a thunderstorm.
  • Fully charge the battery at the end of the season before winter storage.

For more information and instructions, read the complete Operator’s manual in the Automower®Connect app or on www.husqvarna.com.

Lampe leuchtet dauerhaft griin Lumiere verte fixe Luce verde fissa Green solid light
Lampe blinkt grun ECO-Modus ist aktiviert. Lumiere verte clignotante Le mode ECO est active. Luce verde lampeggiante E attiva la modality ECO. Green flashing light ECO mode is activated.
Lampe blinkt blau Lumiere bleue clignotante  Luce blu lampeggiante Blue flashing light
Lampe blinkt rot Lumiere rouge clignotante Luce rossa lampeggiante  Red flashing light
Lampe leuchtet dauerhaft rot Fehler . Lumiere rouge fixe Luce rossa fissa Red solid light

 

  1. Automower® Connect
    A. Download the Automower® Connect app from AppStore or GooglePlay.
    B. Sign up and specify an e-mail address and a password to create a Husqvarna account.
    C. login to your Husqvarna account in the app.
    D. Select My mowers in the Automower® Connect app, and then select the plus sign (+).
    E. Follow the instructions in the app.
  2. Connectivity
    A. Long-range cellular connectivity.
    B. Short-range Bluetooth® connectivity (Automower® ).
    C. Device tracking (GPS). Available with Automower® Connect (Automower® ).

AUTOMOWER® IST EINE MARKE VON HUSQVARNA AB. COPYRIGHT © 2021
AUTOMOWER® IS A TRADEMARK OWNED BY HUSQVARNA AB. COPYRIGHT ©
2021 HUSQVARNA. ALL RIGHTS RESERVED.
www.husqvarna.com
QG_P2_1142656.indd 8
2021-01-14 18:00:21