Sony HT-X9000F Active Speaker System Owner’s Manual

SONY HT-X9000F Active Speaker System Owner’s Manual

SERVICE MANUAL

Ver. 1.1 2018.03

• All of the units included in the HT-X9000F (SA-X9000F/SA-WX9000F/Remote control) or HT-XF9000 (SA-XF9000/SAWXF9000/
Remote control) are required to confi rming operation of SA-X9000F/ XF9000. Check in advance that you have all of the units.

Note:

Be sure to keep your PC used for service and checking of this unit always updated with the latest version of your anti-virus software.
In case a virus affected unit was found during service, contact your Service Headquarters.

COMPONENT MODEL NAME

HT-X9000F HT-XF9000
Bar Speaker (Active Speaker System) SA-X9000F SA-XF9000
Subwoofer (Active Subwoofer) SA-WX9000F SA-WXF9000

Amplifier section

(X9000F: US)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION:
FTC)
Front L + Front R:
With 4ohms loads, both channels driven, from 200 – 20,000Hz; rated 35W per channel minimum RMS
power, with no more than 1% total harmonic distortion from 250mW to rated output.
POWER OUTPUT (reference)
Front L/Front R speaker blocks: 100W (per channel at 4ohms, 1kHz)
(X9000F: CND, AUS, EA, SP, TW, TH, LA/ XF9000)
POWER OUTPUT (rated)
Front L + Front R: 60W + 60W (at 4ohms, 1kHz, 1% THD)
POWER OUTPUT (reference)
Front L/Front R speaker blocks: 100W (per channel at 4ohms, 1kHz)
(X9000F: CH)
POWER OUTPUT (rated)
Front L + Front R: 60W + 60W (at 4ohms, 1kHz)
Inputs
HDMI IN*
ANALOG IN TV IN (OPT)
Outputs
HDMI OUT (TV (ARC))*
*HDMI IN and HDMI OUT (TV (ARC)) jacks
support HDCP 2.2 protocol. HDCP 2.2 is newly enhanced copyright protection
technology that is used to protect content such as 4K movies.
HDMI Section
Connector
Type A (19pin)

BLUETOOTH section

Communication system
BLUETOOTH Specification version 4.2 Выходное напряжение:
(XF9000: RU) Постоянный ток 5 В Output BLUETOOTH Specification Power Class1
Maximum communication range Line of sight approx. 30m 1) Maximum number of devices to be
registered 9 devices Frequency band 2.4 GHz band (2.4GHz – 2.4835GHz) Modulation method FHSS (Freq Hopping Spread Spectrum) Compatible BLUETOOTH profiles2)
A2DP (Advanced Audio Distribution Profile) AVRCP (Audio Video Remote Control Profile) Supported Codecs3) SBC4), AAC5) Transmission range (A2DP)
20 Hz – 20,000 Hz (Sampling frequency 32kHz, 44.1kHz, 48kHz) (X9000F: CH)

  1. The actual range will vary depending on factors such as obstacles between devices, magnetic fields around a microwave oven, static electricity, cordless phone use, reception sensitivity, the operating system, software applications, etc.
  2. BLUETOOTH standard profiles indicate the purpose of BLUETOOTH communication between devices.
  3. Codec: Audio signal compression and conversion format
  4. Abbreviation for Subband Codec
  5. Abbreviation for Advanced Audio Coding

SPECIFICATIONS

Front L/Front R speaker block section Speaker system
Full Range speaker system, Acoustic suspension Speaker 40mm × 100mm (1 5/8 in. × 4 in) cone type.

General

Power requirements
120 V AC, 60 Hz (X9000F: US, CND)
120 V AC, 50 Hz/60 Hz (X9000F: TW) Power consumption On: 38W [Bluetooth Standby] – [On]: Less than 2W
[Bluetooth Standby] – [Off]: Less than 0.5W
Dimensions* (approx.) (w/h/d) 930mm × 58mm × 85mm (36 5/8 in × 2 3/8 in × 3 3/8 in) *Not including projection portion Mass (approx.)
2.5kg (5 33/64 lb) Frequency band 2.4GHz (2.4000GHz – 2.4835GHz) Modulation method FHSS (Freq Hopping Spread Spectrum) Design and specifications are subject to change without notice. Wireless Transmitter/ Receiver Section 220 V – 240 V AC, 50 Hz/60 Hz (X9000F: AUS, CH, SP, TH/XF9000) 120 V – 240 V AC, 50 Hz/60 Hz (X9000F: EA, LA)

What’s in the Box

  • Bar Speaker (1)
  • Subwoofer (1)
  • Remote control (1)
  • R03 (size AAA) battery (2)
  • HDMI cable (supports the specification equal to Premium High Speed HDMI
    Cable with Ethernet) (1) (X9000F: US, CND, AUS, CH, EA, SP, TW, TH, LA/XF9000: RU)
  • Optical digital cable (1) (XF9000: AEP, UK)
  • WALL MOUNT TEMPLATE (1)
  • Startup Guide
  • Operating Instructions

Design and specifications are subject to change without notice.

SECTION 6 EXPLODED VIEWS

Note:

  • XX and -X mean standardized parts, so they may have some difference from the original one.
  • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.
  • The mechanical parts with no reference number in the exploded views are not supplied.
  • Color Indication of Appearance Parts Example: KNOB, BALANCE (WHITE) . . . (RED)

The components identifi ed by mark 0 or dotted line with mark 0 are critical for safety.
Replace only with part number specifi ed.
The components identifi ed by mark 9 contain confi dential information.
Strictly follow the instructions whenever the components are repaired and/or replaced.

6-1. FOOT SECTION

HT-X9000F/XF9000

6-2. TOP CABINET SECTION

6-3. BOTTOM CABINET SECTION

Note 1: When the bluetooth module (Ref. No. BT1) is replaced, be sure to refer to “WIRELESS CONNECTION (LINK) WORK OF BAR SPEAKER AND SUBWOOFER” on page 6.
Note 2: Ref. No. ACP1 is a service part used only for the SP model sold in Hong Kong.

6-4. MAIN BOARD SECTION

Note 2: When the complete MAIN board (Ref. No. 153) is replaced, be sure to refer to “SERIAL NUMBER WRITING WORK WHEN THE MAIN BOARD REPLACED” on page 5.

6-5. SK1 AMP BOARD SECTION

Note 2: When the complete SK1 AMP board (Ref. No. 202) is replaced, spread the compound to the touching portion between the IC6006 and the heat sink.

HT-X9000F/XF9000

6-6. POWER BOARD SECTION

HT-X9000F/XF9000 57 Ver. 1.1

 

Read More About This Manual & Download PDF: