VIKING MAGNI2500 Magni 2500 Battery Generator User Manual

MAGNI2500 Magni 2500 Battery Generator

User Manual

Safety instructions

Please observe the following instructions to ensure safe usage:

Do not alter or disassemble this product.
Do not move during charging or using it, because the vibration and impact during
moving will lead to poor contact of output interface.
In case of ﬁre, use dry powder ﬁre extinguishers for this product. Do not use water ﬁre extinguisher, which may cause electric shock.
Close supervision is required when using this product near children.
Please conﬁrm the rated speciﬁcation of your load, and do not use it beyond the speciﬁcation.
Do not place the product near heat sources, such as electric furnace and heaters.
Not permitted on apricates because the battery capacity exceeds 100Wh.
Do not touch the product or the plug-in points if your hands are wet.
Check the product and accessories prior to every use. Do not use if it is damaged or broken.
Please unplug the AC adapter from the wall outlet immediately in case of lightning stroke, which may cause heating, ﬁre and other accidents.
Use original charger and cables.

Description of product:

1. Port for DC 12V/10A cigarette charger
2. 2 x Output DC 12V / 10A
3. DC 12V / 25A output
4. 2 x USB-A 18W output
5. 100W USB-C output
6. 2 x USB-A output 5V/3A
7. PV / Car input port
8. Charging Adapter Input Port
9. 2 x Wireless charging 15W
10. Touch Interaction LCD Display
11. ON/OFF power button
12. 4 x AC output

Contents of the pack

Startup and shutdown operation

(1) Start up: short press the power button, the indicator light is on, and the machine is in standby mode.
(2) Shutdown: press and hold the power button for more than 2 seconds, and the indicator light will be oﬀ and the machine shut oﬀ.

(3) DC power switch and AC power switch are integrated in the interaction LCD screen(Figure 1), press “DC ON/OFF” button and “AC ON/OFF” button on the screen to turn on/off the DC /AC output.

How to use the touch screen

Interaction LCD screen(Information Vision) supports below functions:
(1) Real time display of voltage, current, power, temperature and state of charge and discharge.
(2) The user can adjust the output voltage, frequency, charging mode, power consumption
mode and time information according to the setting column.
(3) Support energy-saving, and enable Super ECO mode to save more than 30% of useless energy loss.
(4) Support users to view fault information, historical fault information, software version independently.

5. The operation steps of touch screen

Warm tip:

The touchable LCD screen is a resistance screen. we recommend to press the touch button by fingernail lightly until it “beeps”.
In order to maximize the lifespan of the LCD screen, please avoid direct sunlight on it.
(1) When press the power button, it will enter the main interface of the LCD display screen:

a. Home Button (main interface)
b. Settings button
c. Data Button
d. Fault button
e. PV/Car charging display
f. BMS info
g. Time/Date
h. DC load info
i. DC ON / OFF button
j. AC ON / OFF button
k. Adapter charging display
l. AC load info

(2) Click the settings button in the main interface (Figure 2) to enter the setting interface as follows (Figure 3) :

Warm tip: Please enter the setting interface to set the date and time according to the local time zone, and check the output voltage, frequency and other parameters for the ﬁrst time. The default:

AC output: 230V/50Hz
DC Input Source: PV (solar)
ECO Mode: NO
Press “Next” button to enter language and date setting as below (Figure 3）:
Language: Japanese, English

Date and Time Settings

On the main home screen, click on the “Settings” button
Go to the other side of the setting to System date settings and Time settings
To set the date and time, click each time value separately (month, day, year, hour, minute, second separately) and set them on the dial.
After setting the date and time, click the “OK” button (in the Time settings line) to conﬁrm the date and time modiﬁcation

Check date and time settings at least once every 2 weeks. There may be a slight deviation from real time.

(3) Return to the main interface (Figure 1), click the “Data” button to enter the page (Figure 4) :

Click the “Product Info” button, you can view the product model, control software version, monitoring software version, BMS monitoring software version and display software version in turn;
Click the “ Inverter & Charger Info” button, you can view the PV / Car operation and the adapter operation status , DC out operation and AC out operation in turn, which can also be accessed directly from the shortcut key on the main interface;
Click the “BMS Maintenance” button, you can view the operation information of BMS, and this part can also be accessed directly from the shortcut key in the main interface;
Click the “Fault History/Alarm” button, you can view all the fault information generated by the machine. All the fault codes recorded here. According to the fault codes, return to the main interface and click the fault button to view the corresponding fault information. Fault History is retained up to 10 years if not manually cleared.

(4) Return to the main interface and click the fault button (Figure 1) to view the current fault information: the fault button will display orange if there is a fault, click to enter the corresponding fault information, then the gray light will turn into orange.

Charging the product

There are four ways to charge:
(1) Charging mode 1: From AC Wall outlet

Press the main power button to start charging after connecting the product to the AC wall outlet, the charging will automatically stop when it reaches 100%.

(2) Charging mode 2: From the solar panels

Choose the solar panel with working voltage DC 35V-150V.
Connect the solar panel to the product via solar charging cable included.
Plug and play charging: it will start charging automatically after connecting the solar panel to the product even it is oﬀ status.
Max. current of the solar is 12A.

(3) Charging mode 3: From the car lighter port

Press the power button and connect it to the cigarette lighter port through the car charging cable.
Enter the setting interface as shown in (Figure2) through the display screen to set DC input source to car mode; The product can be charged with 8.2A maximum current.

(4) Charging Mode 4: From a generator (gasoline, propane or diesel)

Connect the AC adapter input to the generator and the output port to the AC charging port of the machine.
Press the power button, the product will be charged, the charging will automatically stop when it reaches 100%.

Discharging

Turn on 12V / 25A, 12V / 3A, cigarette lighter port, USB and type C output: first, press the power button, then enter the main interface through the touch screen, click the DC ON/ OFF button and confirm, Turn off these output, and also click the DC on / off button and confirm.
Turn on AC output: first, press the power button, then enter the main interface through the touch screen,
click the AC ON/ OFF button and confirm. Turn off these AC output ports, and also click the AC ON/ OFF button and confirm

Application scenario

Outdoor: Car equipment: car fridge, car vacuum cleaner and other car equipment;
Camping equipment: garden electric tools (power tools such as blowers, lawn mowers, electric drills, electric saws), BBQ grills, LED lights, etc.
Indoor: Refrigerator, kitchen devices such as kettle, toaster, blender, coffee maker, rice cooker, laptops, phones, lighting, etc.

Examples of loads

12V / 25A, 12V / 3A, cigarette lighter port, USB and type C output port are suitable for most products in the market, but some products may trigger overcurrent protection if there is a large current impact at the moment of starting.
The power of electrical products used for AC output should be less than 2000W. According to the diﬀerent electrical products, when the rated power is less than 2000W, some air conditioners, motors and other devices that need instantaneous high current when starting may trigger overcurrent when the ratio of peak value of rated current exceeds 3:1. At this time, we recommended that you select the electrical appliances with lower power rate.
When the output is overload, over-current or short circuit, the product will turn oﬀ the corresponding output, and then it will automatically start twice (at an interval of 20s). If there is still an overload, over-current or short circuit alarm, the output will be locked, and it needs to be manually troubleshooting and then restart. If the output stops repeatedly after restart, please stop using it immediately (only after troubleshooting) or contact the seller or maintenance agent for help.
When the battery power is discharged to 0%, the DC and AC output will automatically turn the battery power is charged to more than 5%, the DC and AC output can be turned on, which the battery and enhance its cycle life.
This machine supports charging and discharging simultaneously.

Estimation of operating time

2000Wh × DOD × η ÷ (load W) = charging time (unit: h）

Note: DOD is the battery discharge depth，
η is the local inverter eﬃciency,
DOD=90%,
η=88%。

Technical speciﬁcations

Storage and maintenance instructions

(1) Please fully charge the machine before storing it.
(2) Turn off all power buttons.
(3) To preserve the battery lifespan, please use and recharge at least once every 6 months.
(4) Ensure proper ventilation while in use or store and keep away from any combustible materials or gases. Do
not stack anything on top of the unit in storage or in use. Inadequate ventilation and/or improper storing may
cause damage to the unit.
(5) Avoid exposing the product to rain or using the product in humid environment.
(6) Use and store the product in a clean and dry environment.
(7) Keep this product away from children and pet.
(8) Wring the cloth with water and wipe it clean In case of dirt.

Declaration

Some changes may be made to the appearance and specifications without prior notice due to the improvement of the product.
Our company shall not be liable for any damage caused by force majeure such as fire, typhoon, flood,
earthquake or the user’s intentional negligence, misuse or other abnormal conditions.
No compensation shall be made for the failure of non standard connector/accessories.
Our company will not bear all responsibilities if the damage is caused by not operating the product according to the use method in the operation manual.
This product is not suitable for use on the relevant equipment or machines involving personal safety, such as
atomic energy devices, aerospace devices, transportation devices, medical devices, etc., or the equipment or
machines that must be highly reliable in electricity. If we use this product on the above-mentioned equipment or machine, we will not be responsible for personal accident, fire accident or wrong action of the machine and equipment caused by the failure of this product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation of the device.

Notice:
Do not dispose of the product at the end of its useful life as unsorted municipal waste, use separate waste
collection points. By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. The recycling of materials will help to conserve natural resources. For more detailed
information about recycling of this product, please contact your local city office, your household waste disposal
service or the shop where you purchased the product.

Common faults and troubleshooting

If this product is unable to charge or power other equipment, please check according to the following steps.
(1) Ensure that the power button is on and the power button light is always on(green).
(2) Make sure the DC ON / OFF button and AC ON / OFF button are on.
(3) Check whether the left of battery capacity is more than 5%. If the left of battery capacity is less than 5%,
please charge as soon as possible.
(4) Ensure that the load equipment meets the power limit of the product, that is, the load power is within the
maximum input range of each output interface; If the above steps still do not solve the problem, please contact
the seller for help.

Warning:
Non-compliance can very likely lead to serious injury or death.

Do not dismantle or adjust the device or battery.
Do not place the device near a ﬁre, or high heat source. Keep out of direct sunlight.
NEVER USE and STORE the device where it may come into contact with water while you are using it, or when you are charging it. Do not use or store the device e.g. in the bathroom, or in a high humidity area, or in the rain, etc.
Only use the output socket to power external devices. Never connect AC under any circumstances
output from the battery generator to power the bat generator socket. There will be irreversible damage outside warranty correction,
DO NOT touch devices or input and output connectors if your hands are wet.
DO NOT SUPPOSE and SUPPOSE any metal objects of the input and output connectors, SPECIAL into
AC power output.
If the device’s battery ﬂuid gets into your eyes, PLEASE them with lukewarm water and immediately
seek medical attention!
Do not discard the device with household waste.
Do not use any inappropriate power cables.
Do not use the device above the specified input and output voltage.
Do not use the device if it is not working properly.
Do not move your device while recharging or using it.
If you noce any damage to your device, stop using it immediately and contact the service centre.
Only use the device in a clean, dry environment. Do not use and store in dusty and wet
environment.
Check the device before each use. Do not use the device if damaged or otherwise broken.
Do not use the device if the power cord is damaged or broken.
STORE OUT OF CHILDREN! Do not let children use the power supply.
Keep this product out of the reach of pets.
Do not use and store the device in a high temperature space or environment.
If fluid from inside the device reaches your clothing, or skin, wash the affected area immediately with water.
In the event of a thunderstorm, disconnect the power cable from the outlet and do not reload the device.
Do not charge the device via power systems that operate outside 100-240V.
Do not use this device for purposes other than those intended.
If rust, strange smells, overheating or other abnormal circumstances are observed on the device, stop using the device immediately and contact the vendor or service centre of the supplier.
The device meets all legal requirements for the transport of dangerous goods.
When transporting by motor vehicle, make sure the device is properly secured.
Charge, use and store the device only at ambient temperatures as specified in the product specification.
Switch off the device immediately if you accidentally dropped it or it was subjected to high vibrations.
Read carefully the instructions for electrical devices that you want to connect to the power supply unit.
Make sure the device you are connecting is turned off before connecting.
Only power devices that meet the Magni 2500 technical specifications with the device.
This battery generator is designed to power Class II appliances (double insulation).

FAQ(Frequently Asked Questions)

What is the depth of discharge (DoD)?
To extend battery life, the portable power station has a DOD setting of 90%, which means that only 90% of the battery capacity can be discharged. Reserve 10% of the energy to avoid damage to the battery due to over discharge.
Can it be charged and discharged at the same time?
Yes, it supports pass through charging for both AC and DC loads. We recommend if you do this that you make sure to fully charge the AC200 at least once per month to extend battery life.
Can AC output charge refrigerator, air conditioner or electric drill?
Lower power for those devices can be charged . It is not recommended to use more than
1400W power. The starting power of refrigerator, air conditioner and electric drill is generally 5-7 times of the nominal power, which is easy to trigger AC overload.
Can two products be used in parallel?
No.
Can I use third-party solar panels?
You can use any solar panels available as long as they have MC4 connectors and when wired together the voltage is between 35V to 150V and no more than 700W.
How do I know if my appliance will work with the product?
When figuring what appliances can be powered with your portable power station, you will need to calculate how much the continuous loads are of each appliance you want to run simultaneously to determine if the total amount of wastes is within the capacity of the generator. You can find the wastage of the appliance by looking at the manufacturer’s information (this information is usually stamped or printed on most appliances and equipment) to measure it’s wastage. Add all wastages of appliances to be run to determine if the total amount of was is within the maximum continuous and surge was.
Can I connect the product to my home circuit breaker box?
Can not.

user manual

CZ/SK/EN/DE/HU

VIKING products are distributed and serviced by:
BONA SPES s.r.o., Řepčín 250, Olomouc 77900, Czechia
VAT No.: 03476774, +420 777 109 009, www.best-power.cz,

Download

VIKING MAGNI2500 Magni 2500 Battery Generator User Manual

Was this manual helpful?