Pioneer IKT-UVL32UL-AG UVC Bacterial Disinfection for Ductless Mini-Split Systems Owner’s Manual
UVC
Bacterial Disinfection
for Ductless Mini-Split Systems
Owner’s Manual
Model Number: IKT-UVL32UL-AG
Specifications
- Input: AC 85-265V 50/60Hz
- Output: DC 12V 8W
- PF > 0.5, Tc < 176 ºF
- LED Input: 6.72W
- Current: 0.56A
- Voltage: 12V
Applicable for These Air System Types
Operation Principles & Technology
Scientific studies say:
The entire UV spectrum can wipe out or neutralize many microorganism species, preventing them from replicating. UVC energy at 253.7 nanometers provides the ideal germicidal effect. A combination of UVC + UVA is very effective at disinfection as well as odor removal.
Prolonged exposure to direct LED UV Light may be harmful to eyes & skin
The Contents of UVC Mini
Improves indoor air quality and fights biological contamination inside mini-splits.
A
UV LED DriverB
RF Receiver (Optional)C
RF Emitter (Optional)D
LED UVC StripE
Screw F
Ring Connector (Optional)G
Adhesive Wire BaseH
Alcohol Wipe I
Mounting PadsJ
Warning StickerK
Wired Switch (Optional)L
UV Shield StripM
Manual
- Only qualified persons should install this product
- Install only in accordance with the relevant building code
- Read instructions carefully, including the safety warnings
Introduction to UVC Mini Kits
UVC MINI KITS are an innovative application of UV disinfection in Mini-Splits and other space-limited systems.
It is normally used to disinfect an air conditioning system, by halting any bio-growth on fan, coils and other surfaces, and related bad odors. It helps substantially to maintain a clean, fresh air conditioner system, improve the indoor air quality, extends life span, and reduces maintenance cost. Because space is tight and sufficient exposure of surfaces are required, the UVC MINI KITS is best installed inside the supply vent with the light shining onto the blower wheel (which is prone to contain concentrated mold growth).
Cutaway View of Typical Installation of UVC MINI KITS in Mini Split
Prolonged exposure to direct LED UV light may be harmful to eyes & skin.
Disconnect power before servicing. Indirect exposure (blue glow) is not harmful.
IMPORTANT!
Install LED strip so that the light shines into the air system, not into the room.
Air System Preparation Before Installation
- Remove the cabinet cover
- Disconnect Power Supply
- Detach filters
- Dismantle the LED display assembly
- Open the control box cover
2b. For systems with the non-removable drain pan, remove the louvers and grills to access. 2a. Detach drain pan to access the area behind it.
3. Unless not required, drill a 2/3 hole to pass connector cable to the back. (By the side of the control box) - IMPORTANT! Disconnect the power supply before you do anything on the installation!
Mounting the UVC LED Strip
- Determine the best location
Clean with cloth for any dust/dirt
Clean out with an alcohol wipe - If needed, cut the strip into the length
that best Its into the space. (Cut-to-length instruction is provided in this manual) - Peel off paper from the adhesive backing on the LED strip. Do this a few at a time and press it down firmly onto the clean surfaces.
- Place the LED strip so the light will shine onto the blower wheel
- Cut the strip only following the instructions by the manufacturer
- DON’T AIM THE UV LIGHT INTO THE ROOM
Install the Light Shield Strip
UVC light shield strip is designed by the manufacturer and recommended to be installed with the UV LED strip. It is adhesive with a special material, to shield these lights which may be exposed INTO THE ROOM.
To install, simply peel off the paper from the adhesive side and stick it firmly to the UV LED strip, with an angle of 90°, upright.
Electric Installation Preparation
Electrical Installation
1. Remove the control box cover and connect the UV LED Driver power cable with the following:
Notice: UVC MINI KIT comes with a wide voltage 85-265VAC power supply.
2a. Connect the UV LED DRIVER cable connector to the strip directly, only if the model is not equipped with either a wired or remote controller.
Electrical Installation
3. Tuck the power cable into the line chase on the back of the unit or place it under the control box or other secure location.
4. T urn on the power supply and confirm that the UVC MINI KIT is working.
5. Apply the UV Warning Sticker to a proper location.
CAUTION
UV LED LIGHT
may be harmful to eyes & skin.
This unit is equipped with an LED UV light disinfection system.
Disconnect power before servicing.
Indirect exposure (blue glow) is not harmful
Cut-to-length Instruction
Actual Length = air outlet vent length which determines the required actual “L”. Locate the best cutting point
First Cut Point(Most Recommended)
- Determine how long you need to cut.
10 cm is a LED Modular Cycle.
2. Cut from the end without the cable! Take off the bushing and prepare to cut.
3. Cut from the First cut point (two copper fin) if >=10cm.If < 10cm, cut at the second point.
4. Seal the end with the bushing, tightly, make sure not to wrinkle the inner LED strip circuit.
Concepts to know
One UV modular cycle is 10cm, which includes UVC(1)+UVA(4)
Factory Pre-Cut Services are not available at this time.
INSTALLATION
Bacterial Disinfection
for Ductless Mini-Split Systems Prevents bio-growth & related odors on fan, coil and other interior surfaces!
Benefits
- Prevent mold and bacteria growth
- Ensure a clean mini-split system
- Extend the life of a mini-split system
- Improve indoor air quality
- Reduce maintenance cost
Kits Include:
- LED Strip (UVA/UVC)
- LED Driver
- Strip Cabinet
- Bushing Block
- Adhesive Sticker
- Hardware
- User Manual
- Cleaning Cloth
Features
- Super compact / High intensity
- Easy fit with simple installation
- 85-265 VAC wide range power supply
- Cut-to-length LED strip design
- Water-resistance / Heat dissipation
- 50,000 hours+ expected LED life
- Three years system warranty
- Designed to fit major brands
- For Wall-Mount, Floor-Ceiling & Cassette