Candy CMBI970LX Wall-Mounted Cooker Hood User Manual

INSTALLATION AND USER’S MANUAL
(CMBI970LX)
(CVMI970LX)

INTRODUCTION

Thank you for choosing this cooker hood.
This instruction manual is designed to provide you with all required instructions related to the installation, use, and maintenance of the appliance. In order to operate the unit correctly and safely, please read this instruction manual carefully before installation and usage. The cooker hood uses high-quality materials and is made with a streamlined
design. Equipped with a large power electric motor and centrifugal fan, it also provides strong suction power, low noise operation, a non-stick grease filter, and easy assembly installation.

SAFETY PRECAUTION

• Never let the children operate the machine.
• The cooker hood is for home use only, not suitable for barbecue, roast shop, and other commercial purposes.
• The cooker hood and its filter should be clean regularly in order to keep them in good working condition.
• Clean the cooker hood according to the instruction manual and keep the unit from the danger of burning.
• Forbid the direct baking from the gas cooker.
• Please keep the kitchen room good convection.
• Before connecting this appliance check that the power supply cord is not damaged. A damage supply cord must be replaced by qualified service personnel only.
• There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels;
• The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels;
• Regulations concerning the discharge of air have to be fulfilled.
• This appliance is not intended for use by persons(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person slide for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Do not flame under the range hood.
• The range hood is not intended to be installed over a hob having more than four hob elements

Electrical Shock Hazard

• Only plug this unit into a properly earthed outlet. If in doubt seek advice from a suitably qualified engineer.
• Failure to follow these instructions can result in death, fire, or electrical shock.

– These shall be adequate ventilation of the room when the range the hood is used at the same time as appliances burning gas or other fuels(not applicable to appliances that only discharge the air back into the room);
– the details concerning the method and frequency of cleaning.
– there is a fire risk if cleaning is not carried out in accordance with the instructions;
– do not flame under the range hood;
– CAUTION: Accessible parts may become hot when used with cooking appliances.

The lamp used in this product is not suitable for use in the lighting of a room.
The purpose of this lamp is to provide illumination for using the product.

Electrical Installation

Direct Connection
The appliance must be connected directly to the mains using an omnipolar circuit breaker with a minimum opening of 3mm between the contacts.
The installer must ensure that the correct electrical connection has been made and that it complies with the wiring diagram.
The cable must not be bent or compressed.
Regularly check the power plug and power cord for damage. If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.
All installation must be carried out by a competent person or qualified electrician. Before connecting the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate.

WARNING: This is a Class I appliance and MUST be earthed
This appliance is supplied with a 3 core mains cable colored as follows:
Brown = L or Live
Blue = N or Neutral
Green and Yellow = E or Earth

The fuse must be rated at 3 Amps.

Standard Installation Accessories List

CEILING MOUNTING INSTALLATION

Air deflector is mentioned as included and not optional.

1. Position the hanging plate on the ceiling and then mark the position of the screw holes. The hanging plate should be securely fixed to the ceiling,
2. Fix the 2pcs brackets to the T-shaped plastic outlet with 4pcs ST3.5x12mm screws provided.
   
   • 11 x ST6 (40 mm)screws for wooden ceiling
   • 8 x expansion bolts for cement ceiling
3. Fix the angle bars to the hanging plate,using the 8 x M5 screws.
   
4. Extend the angle bars to the required height and then fix them in position using the 16 x M5 screws and nuts with metal washers.
   • IMPORTANT: The angle bars must have an overlap of AT LEAST 100 mm.
   
5. If your cooker hood is going to be used in extraction mode, then you should connect the ducting hose to the ceiling adaptor at this point. Fix the upper chimney section to
   the hanging plate, using the 4 x self-tapping screws.
   Slide the lower chimney section onto the angle bars and raise it until it sits just below the upper chimney section.
6. If the glass canopy has not been pre-assembled by the factory, then it should be fixed to the top of the main body of the cooker hood at this stage.
7. Lift the main body of the cooker hood onto the angle bar and then fix it into position using the 16 x M5 screws.
   • IMPORTANT: This stage of the installation process MUST be completed by two people.
   • IMPORTANT: The 16 x M5 screws MUST be securely tightened.
8.  If you are going to be using the hood in extraction mode, you should fix the ducting hose to the spigot.

• The electrical connection must correspond to the electrical requirement noted on the rating plate, which is placed inside the cooker hood. The appliance should now be connected to the electrical supply.
• Check that the appliance is operating correctly by selecting each speed and switching the light bulbs on and off.
• Remove the hanging hook and then slide the lower chimney section downwards, until it rests against the main body of the cooker hood.
• Use a stainless steel cleaner and polish the stainless steel sections of the appliance.
•If you are using the appliance in recirculation mode, then you should now fit the carbon filter.
• “Please kindly be noted: T-shaped plastic outlet and vflaps can not be used at the same time. You can use them in two ways:
1) Add v-flap on existing outlet;
2) Use T-shaped plastic outlet, no add v-flap.”
• “Note: The product is provided with vflap accessory. This accessory is not mandatory for installation, operation on and use of the product.”

DESCRIPTION OF COMPONENTS

OPERATION

Button 1
The button indicates backlit, when you press the button, the backlit will be turned on and the fan will be turned on at low speed. when pressed again, it will turn off the fan.
It’s used for Ventilation in the kitchen. It is suitable for simmering and cooking which do not make much steam.

Button 2
The button is with indicates backlit, when you press the button, the backlit will be turned on and the fan will be turned on at Medium Speed. when pressed again, it will turn off the fan.
Airflow speed is ideal for ventilation in standard cooking operations.

Button 3
The button is with indicates backlit, when you press the button, the backlit will be turned on and the fan will be turned on at High Speed. when pressing again, it will turn off the fan.
When a high density of smoke or steam is produced, press the high-speed button for the highest effective ventilation.

NOTE: If Low / Medium / High-speed buttons are press at the same time, the unit will only operate at the highest speed.
Light button

MAINTENANCE

Before cleaning switch the unit off and pull out the plug.

1. Regular Cleaning
   Use a soft cloth moistened with hand-warm mildly soapy water or household cleaning detergent. Never use metal pads, chemicals, abrasive material, or stiff brushes to clean the unit.
2. Monthly Cleaning for Grease Filter
   ESSENTIAL: Clean the filter every month can prevent any risk of fire. The filter collects grease, smoke, and dust…… so the filter is directly affecting the efficiency of the cooker hood. If not cleaned, the grease residue (potential flammable) will saturate the filter. Clean it with household cleaning detergent.
3. Annual Cleaning for Activated Carbon Filter
   Apply SOLELY to a unit that is installed as a recirculation unit (not vented to the outside). This filter traps odors and must be replaced at least once a year depending on how frequently the cooker hood used.
4. Changing a light bulb
   Remove the screws on the glass, and take off the hood glass. Find the bulb that requires replacement, you will find it located in the light a fixture which is inside the exposed section of the canopy.

Disconnect the light wiring point and remove the bulb holders and wiring from the hood. Important: It’s not possible to replace the bulbs individually, it will be necessary to obtain the bulbs, bulb holders, and wiring as a complete part. (LED light: MAX 1.5W)
Fit the replacement bulbs, bulb holders, and wiring in the same manner as the originals. Then reconnect the light wiring point.
Refit the hood glass and fasten the glass screws. Make sure the screws are fully tightened.

TROUBLESHOOTING

CUSTOMER ASSISTANCE SERVICE

If you cannot identify the cause of the operating anomaly, switch off the appliance and contact the Assistance Service.
PRODUCT SERIAL NUMBER. Where can I find it?
It is important for you to inform the Assistance Service of your product code and its serial number (a 16 character code that begins with the number 3); this can be found on the guarantee certificate or on the data plate located on the appliance.
It will help to avoid wasted journeys to technicians, thereby (and most significantly) saving the corresponding callout charges.

ENVIRONMENTAL PROTECTION

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

This appliance is marked according to the European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this
product.
The symbol on the product indicates that this product may not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local environmental regulations for waste disposal.
For more detailed information about the treatment, recovery, and recycling of this product, please contact your local city office, your household waste disposal service, or the shop where you purchased the product.