Motorola Q11 AX3000 Dual-Band Mesh WiFi Device User Manual
Motorola Q11 AX3000 Dual-Band Mesh WiFi Device
LABEL SYMBOLS
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
- Additional FCC and Regulatory Compliance information can be found at: http://www.motorolanetwork.com
LIMITED WARRANTY
MTRLC LLC warrants this product against defects in material and workmanship for a warranty period of 2 years. To read the full warranty. please visit www.motorolanetwork.com/warranty.
SAFETY NOTICES
Devices are intended to be placed indoors in an environment that’s between 32° and 104° F (O-40°C) Avoid water and spills Leave room for airflow around the device, do not block the vents on the rear or bottom Mark information is located on the bottom of the product The power adapter plug is used as the disconnect device. The connected AC power outlet must be located near the equipment and be easily accessible
FRONT PANEL LIGHTS
The light on the front of the unit displays status information.
LET’S GET STARTED
- Download the motosync app for iOS or Andriod
- Create a motosync account
- Set up your Motorola device
IN THIS PACKAGE
- 11 router/ extender
1st device set up will be the router - Power adapter
1 per device - Ethernet cable
1 per package
BUTTONS AND PORTSIPLACE
WAN/LAN Port
For the router, connect the Ethernet cable from this port to your internet device (e.g. modem) For an extender, this port can be used as a second LAN port to connect wired devices
USB-C Power
Connect the supplied USB-C 5V 15W AC adapter
LAN Port
LAN port to connect wired devices
PLACEMENT TIP
We recommend placing your extender midway between the router and the desired WiFi coverage area. If you have multiple extenders, evenly space them throughout your home. See the example below.
Choose an elevated, uncovered location
Additional Regulatory Compliance Information
This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give their product to a competent recycling organization or to the retailer when they buy a new Electrical or electronic equipment.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Note
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. LLAN operation in the 5.9GHz band is restricted to Indoor Use Only.
RF Exposure Information
This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications Commission of the U.S. Government. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 24 cm during normal operation.
ISED Notice
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
- CAN ICES-003 (B)/NMB-003(B)
- This Class B digital apparatus complies with Canadian ICES-O03.
- Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
ISED RF Exposure Statement
This device complies with ISED RSS-102 RF exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the IC RSS-102 RF exposure limits, human proximity to the antenna shall not be less than 24 cm during normal operation.