SILVERCREST SSMKC 600 A1 Kitchen Tool Blender Instruction Manual

SILVERCREST SSMKC 600 A1 Kitchen Tool Blender

Introduction

Congratulations on the purchase of your new appliance. You have selected a high-quality product. These operating instructions are a part of this product. They contain important information on safety, usage and disposal. Before using the product, familiarise yourself with all operating and safety instructions. Use the product only as described and only for the speciﬁed areas of application. In addition, pass these documents on, together with the product, to any future owner.

Intended use

This appliance is intended exclusively for …

mixing, puréeing and stirring foods as well as crushing ice cubes,
use exclusively in normal domestic amounts and only for private use in a domestic environment in dry rooms.

This appliance is not intended for …

chopping herbs, onions, meat and hard food components such as nuts, pits, large seeds or stalks,
making nut puree,
the processing of materials that are not foodstuﬀs,
commercial or industrial use,
for use in damp environments or outdoors,
processing hot/boiling liquids.

Package contents

After unpacking, check to ensure all items are available. The package contains:

Motor block, with power cable and plug
Blender
Lid
Measuring cap
Operating instructions

Description of the appliance

Measuring cap
Lid
Blender
Cutting blades
Switch
Motor block
Cable retainer
Scale
Rubber lid seal

Technical data

The CO time (continuous operation time) is the amount of time an appliance can be operated without the motor overheating and becoming damaged. When the speciﬁed CO time has been reached, the appliance must be switched oﬀ until the motor has cooled down to room temperature.

Safety instructions

DANGER! ELECTRIC SHOCK!

Ensure that the appliance, the power cable, and the power plug are never immersed in water or other liquids.
Use the appliance only in dry rooms; never use it outdoors or in damp environments.
Ensure that the power cable never becomes wet or damp during operation. Route the power cable in such a way that it cannot become trapped or damaged in any way.
Arrange for defective power plugs and/or cables to be replaced as soon as possible by a qualiﬁed technician or by our Customer Service Department to avoid the risk of injury.
Always remove the plug from the power socket after use. Switching oﬀ the appliance is not suﬃcient because the appliance receives power as long as the power plug is connected to the socket.
Check to ensure that the appliance is in a serviceable condition before use. The appliance may not be used if it shows signs of damage, especially to the motor block or the blender attachment.
Remove the plug from the socket immediately if you notice unexpected smells or noises coming from the appliance while it is in use or if there is an evident malfunction.

WARNING! RISK OF INJURY!

NEVER insert your hand or ﬁngers into the blender, especially when it is in use. The cutting blades are extremely sharp!
DO NOT remove the lid when the appliance is in operation.
To ensure you can react immediately in the event of danger, never leave the appliance running unattended.
Do not insert cutlery items or mixing tools into the blender while the appliance is in use. There is a considerable risk of injury if these come into contact with the swiftly rotating cutting blades!
Children should be supervised to ensure that they do not play with the appliance.
Never use the appliance for purposes other than those described in these instructions.
Risk of injury if appliance is misused.
The appliance should always be disconnected from the mains when not supervised and before assembly, disassembly or cleaning.
This appliance is not to be used by children.
The appliance and its mains cable must be kept away from children.
This appliance can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning safe use of the appliance, and if they are aware of the potential risks.
Do not allow children to play with the appliance.
Be careful when handling the appliance. The cutting blades are extremely sharp!
Take care when emptying the blender! The cutting blades are extremely sharp!
Take care when cleaning the appliance! The cutting blades are extremely sharp!
Switch the appliance oﬀ and disconnect the plug from the power supply before changing accessories or getting hold of parts that move during operation.
Always make sure that the blender is switched oﬀ before removing the jug from the motor block!
Use the blender only with the supplied motor block!

CAUTION! MATERIAL DAMAGE!

Do not use the appliance in direct sunlight or near any heatgenerating appliances.
NEVER ﬁll the blender with boiling liquids or other foods!Allow these to cool to a lukewarm temperature.
NEVER operate the appliance when it is empty, i.e. without ingredients in the blender attachment.

Unpacking

Remove all packaging materials or protective ﬁlms from the appliance. Retain the packaging, so that you can store the appliance safely or send it by post,
e. g. if it needs to be repaired.
Before using the appliance, check that it is free of damage; check also that the power cable and plug as well as all accessories and appliance parts are undamaged.
Clean all components carefully before using the appliance for the ﬁrst time (see “Cleaning”).

Setting up

Once all components have been cleaned as described in the section “Cleaning”:

Position the appliance so that, …
- that the mains cable passes through the recess at the rear of the appliance,
- the power plug is immediately accessible, so that it can be quickly withdrawn in the event of danger,
- that it is stable and not liable to slip, and so that the sucker feet can attach ﬁrmly and the appliance cannot tip over due to vibration,
- that the mains cable is not in the working area and thus does not present a risk of being inadvertently snagged and tipping the appliance over.

Operation

The motor switches oﬀ automatically as soon as the blender 3 is removed from the motor block 6 or the lid 2 is opened. In such cases it may be easy to forget that the machine is still switched on. The motor will then start unexpectedly as soon as the blender attachment 3 is ﬁtted or the lid 2 is closed again:
Therefore:
- Do not insert the power plug into the wall socket until the blender 3 is ﬁlled and mounted with its lid ﬁtted and closed.
- Before ﬁtting the blender, always check to see that the appliance is switched oﬀ or that the power plug has been removed.
- Switch the appliance oﬀ ﬁrst, pull the plug out and wait until the motor has come to a standstill before removing the blender 3 or opening the lid 2.

Fitting and ﬁlling the blender

Rotate the blender 3 anticlockwise until the arrow under the blender 3 handle is located above the position. Remove blender 3 from motor block 6 in a vertical, upward motion.
Remove lid 2 by rotating it anticlockwise towards position (see Fig 1) until you can pull it upwards.
Fill the blender 3 to at least to the lowest line of the scale 8 and at most to the MAX mark. For optimum results, we recommend the following maximum ﬁlling quantities:
Press the lid 2 ﬁrmly down onto the blender 3. Close lid 2 by turning it clockwise to position until it audibly engages (see Fig. 2). Ensure that the pouring spout on the blender 3 is closed. The motor cannot start until the lid 2 is ﬁtted ﬂush.
Press the measuring cap 1 into the lid as far as the stop.
Place the ﬁlled and closed blender 3 on the motor block 6. To do this, use the recesses on the motor block 6 and ensure that the arrow on the blender is pointing to the symbol while doing so. Turn the blender 3 clockwise to position it until it audibly engages. The motor cannot start until the blender 3 is ﬁtted ﬂush.

Selecting the speed setting

Once the blender 3 is ﬁlled and sitting completely closed on the motor block 6, you can switch on the appliance. Set the switch 5 to …

Level 1 – 3
for liquids or soft foodstuﬀs, for mixing, blending and stirring
Level 3 – 5
for more solid foods or for chopping
Level P (pulse function)
for short, powerful impulse operation, e.g. for crushing ice cubes or when cleaning. To prevent overloading the motor, switch 5 does not lock in this position. Therefore, hold switch 5 in this position for short periods only.

NOTE

Fill the blender 3 with a maximum of 180 g of ice cubes. Otherwise, the ice cubes will not be crushed optimally.

Filling while in use

WARNING!

If you want to add additional foods during operation, use only the measuring cap 1 provided for this purpose. Do NOT open the lid 2.
Do not insert cutlery items or mixing tools into the blender 3 while the appliance is in use. There is a considerable risk of injury if these come into contact with the swiftly rotating cutting blades 4!

To add more food while the appliance is in use, …

Remove the measuring cap 1 from the lid 2.
Add the ingredients.
Press the measuring cap 1 back into the lid.

Removing the blender

Once you have ﬁnished processing the food in the attachment:

Always start by setting switch 5 to the oﬀ position (“0”) and pulling out the mains plug.
Wait until the motor has come to a complete standstill before lifting the blender 3 oﬀ the motor block 6. Rotate the blender 3 anticlockwise until the arrow under the blender 3 handle is located above the position. Remove blender 3 from the motor block 6 in a vertical, upward motion.

Useful tips

To achieve the best results when puréeing ﬁrm ingredients, add small amounts one after the other into the blender 3 rather than a single large portion.
When processing ﬁrm ingredients, cut them into small pieces (2 – 3 cm).
Add at least 50 ml of liquid when pureeing fruit or vegetables.
Add thicker ingredients (such as yogurt) into the blender 3 ﬁrst. If any of the ingredients are not picked up during mixing, remove blender 3 from the motor block 6, remove lid 2 and stir the ingredients with a suitable implement, such as a spoon. Replace the blender 3 back on the motor block 6 with the lid 2 closed and continue mixing.
When mixing liquid ingredients, start oﬀ with a small amount of liquid. Gradually add more liquids to the mixture through the measuring cap.
The appliance can be stabilized by placing your hand on top of the closed blender during operation.
For stirring solid or very thick liquid foods, it can be useful to use level P to prevent the cutting blades 4 from blocking.

NOTE

Do not use the appliance to grind crystals of cooking salt, reﬁned sugar or white sugar. For example, to make powdered sugar.

Recipes

Banana shake

2 bananas
approx. 2 tbsp. sugar (depending on the ripeness of the bananas and personal taste)
½ l milk
1 dash of lemon juice

Peel the bananas and liquidize them at level 2. Gradually add the milk, then the sugar and the lemon juice. Keep mixing everything until you have a smooth and uniform liquid. Serve the shake chilled.

Vanilla shake

¼ l milk
250 g vanilla ice cream
125 g ice cubes
1½ tsp. sugar

Crush the ice cubes using level P. Place the remaining ingredients into the mixer. Mix everything at Level 2 until the liquid has a smooth consistency.

Cappucino shake

65 ml cold espresso (or a very strong coﬀee)
65 ml milk
15 g sugar
65 g vanilla ice cream
100 g ice cubes

Crush the ice cubes using level P. Add the espresso, milk and sugar. Mix everything together at level 2 until the sugar has dissolved. Finally, add the vanilla ice cream and then brieﬂy mix everything together at level 1.

Tropical mix

125 ml pineapple juice
60 ml papaya juice
50 ml orange juice
½ small tin of peaches with juice
125 g ice cubes

Crush the ice cubes using level P. Place all ingredients into the mixer and blend them together at level 3.

Nut nougat shake

½ l milk
200 g nut nougat spread
1 scoop of vanilla ice cream
50 ml cream

Add all the ingredients to the blender and mix at level 3 until everything is evenly blended together.

Carrot shake3

300 ml apple juice
500 ml carrot juice
4 tbsp. cooking oil (wheatgerm oil or rapeseed oil)
4 tbsp. of lemon juice
Powdered ginger
Pepper

Add the apple juice, cooking oil and lemon juice into the blender and mix everything together at level 2. Then add the carrot juice and mix everything together at level 2. To ﬁnish, add the powdered ginger and pepper to taste.

Blackcurrant mix

2 tsp. honey
2 bananas
¼ l buttermilk
¼ l blackcurrant juice

Place all ingredients into the mixer and blend them together at level 3.

Hawaii shake

4 bananas
¼ l pineapple juice
½ l milk
2 tbsp. honey
¼ l rum

Peel the bananas and liquidize them at level 2. Then add the other ingredients and mix everything together at level 1.

Fruity pineapple and strawberry mix

250 ml pineapple juice
200 g strawberries
300 ml apple juice
4 ice cubes

Wash the strawberries and remove the green parts. Crush the ice cubes using level P. Liquidize them at level 2. Then add the other ingredients and mix everything together at level 1.

Andalusian cold soup (gazpacho)

½ cucumber
1 large tomato
1 green pepper
½ onion
1 garlic clove
½ white bread roll
½ tsp. salt
1 tsp. red wine vinegar
1 tbsp. olive oil

Cut the vegetables into pieces approx. 2 cm in size. Start by adding the ﬁrst the tomatoes and then the cucumber to the blender. Liquidize them at level 3. Add the remaining ingredients and then liquidize/blend them all together at level 3 until a smooth soup is created. Serve the soup with bread.

NOTE

These recipes are provided subject to change. All ingredients and preparation information are guiding values. Adapt these recipe suggestions based on your personal experience.
In cases of lactose intolerance, we recommend you use lactose-free milk. Keep in mind, however, that lactose-free milk is a little sweeter.

Cleaning

DANGER! ELECTRIC SHOCK!

Before starting to clean the blender and its components:

Ensure that the motor is switched oﬀ and the power plug removed from the socket.
Do not immerse the motor block 6 in water or other liquids. This could result in you receiving a fatal electric shock and cause damage to the appliance.
Never open the housing of the appliance. Otherwise, there is a risk of a fatal electric shock.

WARNING! RISK OF INJURY!

Never insert your hand or ﬁngers into the blender 3, especially while it is in use. The cutting blades 4 are extremely sharp!

CAUTION! PROPERTY DAMAGE!

Do not use solvents or abrasive cleaners on the plastic surfaces, they could be damaged by them.

Cleaning the blender

To prevent injuring yourself on the cutting blades 4, clean the blender 3 only with a long-handled washing-up brush.
Clean the measuring cap 1 and the lid 2 in mild soap solution. Ensure that the rubber seal 9 is correctly ﬁtted before using lid 2 again.

NOTE

You can also clean lid 2, measuring cap 1 and blender 3 with the cutting blade 4 in your dishwasher. If possible, place all the parts in the upper basket of the dishwasher and make sure that they are not jammed in place.

If you clean the appliance directly after use, you can usually achieve suﬃciently hygienic cleaning results by using the following alternatives: Fill the blender 3 with 750 ml of water and add a couple of drops of mild washing up liquid. Close lid 2 and ﬁt the blender 3 onto motor block 6. Insert the mains plug into the socket and activate the pulse function a few times so that the cutting blades 4 ploughs through the water at maximum speed. Afterward, rinse the blender 3 with plenty of clean water to remove any washing-up liquid residues.
To remove stubborn dirt, you can remove the attachment A with the cutting blades 4 from the jug B of the blender 3:

Remove blender 3 from the motor block 6. For better stability, remove lid 2 (see ﬁg. 1).
Turn the appliance upside down and turn attachment A anticlockwise so that it can be detached from the jug B (see ﬁg. 3).
Clean attachment A and the jug B thoroughly in a mild soap solution or in the dishwasher.
Dry all parts thoroughly before reassembling them.
Replace attachment A with cutting blade 4 onto the jug B of the blender 3 and turn it clockwise.

Cleaning the motor block

Clean the surfaces with a damp cloth. If necessary, apply a mild washing-up liquid to the cloth. Afterward, wipe oﬀ with a cloth moistened only with water to ensure that no detergent remains on the appliance. Then dry the surfaces thoroughly.
When cleaning, always check that the contact switch in the ﬁtting for the blender 3 is not blocked by soiling residues. If you cannot dislodge any blockages with the corner of a piece of paper, make contact with Customer Services. Do not use any hard objects, these could damage the contact switch.
Remove any possible residues on the underside of the motor block 6 with a dry cloth or a stiﬀ-bristled brush only. Ensure that nothing can get in through the ventilation openings of the appliance.

After cleaning

Allow all parts to dry well before reassembling and reusing the liquidizer.

Storage

If you do not intend to use the blender for an extended period, clean it thoroughly (see chapter “Cleaning”).
Wrap the mains cable around the cable retainer 7 on the base of the motor block 6 in the direction of the arrow.
Store the blender in a cool and dry location.

Disposal

Do not dispose of the appliance in your normal domestic waste. This product is subject to the provisions of European Directive 2012/19/EU. Dispose of the appliance via an approved waste disposal company or your municipal waste disposal facility. Please comply with all applicable regulations. Please contact your waste disposal facility if you are in any doubt.
Your local community or municipal authorities can provide information on how to dispose of the worn-out product.
Note the labeling on the packaging and separate the packaging material components for disposal if necessary. The packaging material is labeled with abbreviations (a) and numbers (b) with the following meanings:
- 1–7: Plastics,
- 20–22: Paper and cardboard,
- 80–98: Composites.
The packaging is made from environmentally friendly material and can be disposed of at your local recycling plant.

Kompernass Handels GmbH warranty

Dear Customer, This appliance has a 3-year warranty valid from the date of purchase. If this product has any faults, you, the buyer, have certain statutory rights. Your statutory rights are not restricted in any way by the warranty described below.

Warranty conditions

The warranty period starts on the date of purchase. Please keep your receipt in a safe place. This will be required as proof of purchase. If any material or manufacturing fault occurs within three years of the date of purchase of the product, we will either repair or replace the product for you or refund the purchase price (at our discretion). This warranty service requires that you present the defective appliance and the proof of purchase (receipt) within the three-year warranty period, along with a brief written description of the fault and of when it occurred. If the defect is covered by the warranty, your product will either be repaired or replaced by us. The repair or replacement of a product does not signify the beginning of a new warranty period.

Warranty period and statutory claims for defects

The warranty period is not prolonged by repairs eﬀected under the warranty. This also applies to replaced and repaired components. Any damage and defects present at the time of purchase must be reported immediately after unpacking. Repairs carried out after expiry of the warranty period shall be subject to a fee.

Scope of the warranty

This appliance has been manufactured in accordance with strict quality guidelines and inspected meticulously prior to delivery. The warranty covers material faults or production faults. The warranty does not extend to product parts subject to normal wear and tear or to fragile parts which could be considered as consumable parts such as switches, batteries or parts made of glass. The warranty does not apply if the product has been damaged, improperly used or improperly maintained. The directions in the operating instructions for the product regarding proper use of the product are to be strictly followed. Uses and actions that are discouraged in the operating instructions or which are warned against must be avoided. This product is intended solely for private use and not for commercial purposes. The warranty shall be deemed void in cases of misuse or improper handling, use of force and modiﬁcations / repairs which have not been carried out by one of our authorized service centers.

Warranty claim procedure

Please have the till receipt and the item number (e.g. IAN 123456_7890) available as proof of purchase.
You will ﬁnd the item number on the type plate on the product, an engraving on the product, on the front page of the operating instructions (below left) or on the sticker on the rear or bottom of the product.
If functional or other defects occur, please contact the service department listed either by telephone or by e-mail.
You can return a defective product to us free of charge to the service address that will be provided to you. Ensure that you enclose the proof of purchase (till receipt) and information about what the defect is and when it occurred. You can download these instructions along with many other manuals, product videos, and installation software at www.lidl-service.com. This QR code will take you directly to the Lidl service page (www.lidl-service.com) where you can open your operating instructions by entering the item number (IAN) 360749_2007.

Service

Service Great Britain
Tel.: 0800 404 7657
E-Mail: [email protected]
Service Malta
Tel.: 80062230
E-Mail: [email protected]

Importer

Please note that the following address is not the service address. Please use the service address provided in the operating instructions. KOMPERNASS HANDELS GMBH BURGSTRASSE 21 44867 BOCHUM GERMANY www.kompernass.com

Download

SILVERCREST SSMKC 600 A1 Kitchen Tool Blender Instruction Manual

Was this manual helpful?