Dewalt DCS565 18V XR Cordless Brushless 165mm Circular Saw Instruction Manual

DCS565 18V XR Cordless Brushless 165mm Circular Saw

DCS565

English (original instructions)

P ( )

( )

Fig. A

10 5 11 9
Fig. B 9

6
7 8 15

xx.xx.xxxx 8

8 14 13 4
Fig. C

2 1
17

Fig. D Fig. F

Fig. E 20
18 15
19 8

8 19 15 18 16

Fig. G

Fig. H 2

Fig. I

Fig. J

Fig. K

Fig. L

Fig. M

5 Fig. N

Fig. O

Fig. P

Fig. Q

English

165 MM CORDLESS CIRCULAR SAW DCS565

Congratulations!
You have chosen a DEWALT tool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional power tool users.
Technical Data

ECDeclaration of Conformity
Machinery Directive
o

Voltage

VDC

Type

Battery type

Noload speed

min1

Blade diameter

Maximum depth of cut

Blade bore

Bevel angle adjustment

Weight (without battery pack)

DCS565 XJ, GB, QW
18 1 LiIon 4950 165 55 20 50° 2.8

165 mm CORDLESS CIRCULAR SAW DCS565
DEWALT declares that these products described under Technical Data are in compliance with: 2006/42/EC, EN.
These products also comply with Directive 2014/30/EU and 2011/65/EU. For more information, please contact DEWALT at the following address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical file and makes this declaration on behalf of DEWALT.

Noise values and/or vibration values (triax vector sum) according to EN6284125:

LPA (emission sound pressure level) dB(A)

LWA (sound power level)

dB(A)

105

K (uncertainty for the given sound dB(A)

level)

Vibration emission value ah,W = m/s2

< 2.5

Uncertainty K =

m/s2

1.5

The vibration and/or noise emission level given in this information
sheet has been measured in accordance with a standardised test
given in EN62841 and may be used to compare one tool with
another. It may be used for a preliminary assessment of exposure. WARNING: The declared vibration and/or noise emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration and/or noise emission may differ. This may significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and/or noise should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the accessories, keep the hands warm (relevant for vibration), organisation of work patterns.

Markus Rompel VicePresident Engineering, PTEEurope DEWALT, RichardKlingerStraße 11, D65510, Idstein, Germany 07.12.2020
a WARNING: To reduce the risk of injury, read the instruction manual.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to
these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury. CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.
Denotes risk of electric shock.
Denotes risk of fire.

English

Batteries

Chargers/Charge Times (Minutes)

Cat #

VDC

DCB181 18

DCB182 18

DCB183/B/G 18

DCB184/B/G 18

DCB185 18

DCB187 18

DCB189 18

Ah Weight (kg) DCB104 DCB107

1.5 0.35

4.0 0.61 60/40** 185

2.0 0.40

5.0 0.62 75/50** 240

1.3 0.35

3.0 0.54

140

4.0 0.54

185

DCB112
45 120 60 150 40 90 120

DCB113
35 100 50 120 30 70 100

DCB115
22 60 30 75 22 45 60

DCB116 DCB117 DCB118

22 60/45**
30 75/60**
22 45 60

22 60/40**
30 75/50**
22 45 60

DCB132
22 60 30 75 22 45 60

DCB119
45 120 60 150 40 90 120

*Date code 201811475B or later
**Date code 201536 or later
GENERAL POWER TOOL SAFETY WARNINGS WARNING: Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or batteryoperated (cordless) power tool.
1) Work Area Safety
a ) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b ) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c ) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
2) Electrical Safety
a ) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
b ) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c ) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
d ) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
e ) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f ) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
3) Personal Safety
a ) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
b ) Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, nonskid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
c ) Prevent unintentional starting. Ensure the switch is in the offposition before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
d ) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e ) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
f ) Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g ) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dustrelated hazards.
h ) Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

4) Power Tool Use and Care
a ) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
b ) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
c ) Disconnect the plug from the power source and/ or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
d ) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
e ) Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
f ) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g ) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
h ) Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
5) Battery Tool Use and Care
a ) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
b ) Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
c ) When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
d ) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
e ) Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit

English
unpredictable behaviour resulting in fire, explosion or risk of injury.
f ) Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130 °C may cause explosion.
g ) Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.
6) Service a ) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
b ) Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.
Safety Instructions for All Saws
Cutting Procedures
a ) DANGER: Keep hands away from cutting area and the blade. Keep your second hand on auxiliary handle, or motor housing. If both hands are holding the saw, they cannot be cut by the blade.
b ) Do not reach underneath the workpiece. The guard cannot protect you from the blade below the workpiece.
c ) Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the blade teeth should be visible below the workpiece.
d ) Never hold the workpiece in your hands or across your leg while cutting. Secure the workpiece to a stable platform. It is important to support the work properly to minimize body exposure, blade binding, or loss of control.
e ) Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting tool may contact hidden wiring. Contact with a “live” wire will also make exposed metal parts of the power tool “live” and could give the operator an electric shock.
f ) When ripping, always use a rip fence or straight edge guide. This improves the accuracy of cut and reduces the chance of blade binding.
g ) Always use blades with correct size and shape (diamond versus round) of arbor holes. Blades that do not match the mounting hardware of the saw will run offcenter, causing loss of control.
h ) Never use damaged or incorrect blade washers or bolt. The blade washers and bolt were specially designed for your saw, for optimum performance and safety of operation.

English
FURTHER SAFETY INSTRUCTIONS FOR ALL SAWS Kickback Causes and Related Warnings
· Kickback is a sudden reaction to a pinched, jammed or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the operator;
· When the blade is pinched or jammed tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back toward the operator;
· If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the wood causing the blade to climb out of the kerf and jump back toward the operator.
Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below:
a ) Maintain a firm grip with both hands on the saw and position your arms to resist kickback forces. Position your body to either side of the blade, but not in line with the blade. Kickback could cause the saw to jump backwards, but kickback forces can be controlled by the operator, if proper precautions are taken.
b ) When blade is binding, or when interrupting a cut for any reason, release the trigger and hold the saw motionless in the material until the blade comes to a complete stop. Never attempt to remove the saw from the work or pull the saw backward while the blade is in motion or kickback may occur. Investigate and take corrective actions to eliminate the cause of blade binding.
c ) When restarting a saw in the workpiece, centre the saw blade in the kerf so that the saw teeth are not engaged into the material. If saw blade binds, it may walk up or kickback from the workpiece as the saw is restarted.
d ) Support large panels to minimise the risk of blade pinching and kickback. Large panels tend to sag under their own weight. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel.
e ) Do not use dull or damaged blades. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and kickback.
f ) Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and kickback.
g ) Use extra caution when sawing into existing walls or other blind areas. The protruding blade may cut objects that can cause kickback.
Lower Guard Function Safety Instructions
a ) Check the lower guard for proper closing before each use. Do not operate the saw if lower guard does not move freely and close instantly. Never clamp
8

or tie the lower guard into the open position. If saw is accidentally dropped, lower guard may be bent. Raise the lower guard with the retracting handle and make sure it moves freely and does not touch the blade or any other part, in all angles and depths of cut.
b ) Check the operation of the lower guard spring. If the guard and the spring are not operating properly, they must be serviced before use. Lower guard may operate sluggishly due to damaged parts, gummy deposits, or a buildup of debris.
c ) The low guard may be retracted manually only for special cuts such as “plunge cuts” and “compound cuts.” Raise the lower guard by retracting the handle and as soon as blade enters the material, the lower guard must be released. For all other sawing, the lower guard should operate automatically.
d ) Always observe that the lower guard is covering the blade before placing saw down on bench or floor. An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch is released.
Additional Safety Instructions for Circular Saws
· Wear ear protectors. Exposure to noise can cause hearing loss.
· Wear a dust mask. Exposure to dust particles can cause breathing difficulty and possible injury.
· Do not use blades of larger or smaller diameter than recommended. For the proper blade rating refer to the Technical Data. Use only the blades specified in this manual, complying with EN8471.
· Never use abrasive cutoff wheels.
· Do not use water feed attachments.
· Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control.
· Use only saw blades that are marked with a speed equal or higher than the speed marked on the tool.
· Avoid overheating the blade tips.
· Install the dust extraction port onto the saw before use.
Residual Risks
In spite of the application of the relevant safety regulations and the implementation of safety devices, certain residual risks cannot be avoided. These are:
· Impairment of hearing.
· Risk of personal injury due to flying particles.
· Risk of burns due to accessories becoming hot during operation.
· Risk of personal injury due to prolonged use.
SAVE THESE INSTRUCTIONS

Chargers
DEWALT chargers require no adjustment and are designed to be as easy as possible to operate.
Electrical Safety
The electric motor has been designed for one voltage only. Always check that the battery pack voltage corresponds to the voltage on the rating plate. Also make sure that the voltage of your charger corresponds to that of your mains.
i Your DEWALT charger is double insulated in accordance with EN60335; therefore no earth wire is required.
If the supply cord is damaged, it must be replaced only by DEWALT or an authorised service organisation.
Mains Plug Replacement (U.K. & Ireland Only)
If a new mains plug needs to be fitted:
· Safely dispose of the old plug.
· Connect the brown lead to the live terminal in the plug.
· Connect the blue lead to the neutral terminal. WARNING: No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs. Recommended fuse: 3 A.
Using an Extension Cable
An extension cord should not be used unless absolutely necessary. Use an approved extension cable suitable for the power input of your charger (see Technical Data). The minimum conductor size is 1 mm2; the maximum length is 30 m.
When using a cable reel, always unwind the cable completely.
Important Safety Instructions for All Battery Chargers SAVE THESE INSTRUCTIONS: This manual contains important safety and operating instructions for compatible battery chargers (refer to Technical Data).
· Before using charger, read all instructions and cautionary markings on charger, battery pack, and product using battery pack.
WARNING: Shock hazard. Do not allow any liquid to get
inside charger. Electric shock may result. WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA or less. CAUTION: Burn hazard. To reduce the risk of injury,
charge only DEWALT rechargeable batteries. Other types of batteries may burst causing personal injury
and damage. CAUTION: Children should be supervised to ensure that they do not play with the appliance.
NOTICE: Under certain conditions, with the charger plugged into the power supply, the exposed charging contacts inside the charger can be shorted by foreign material. Foreign materials of a conductive nature such

English
as, but not limited to, steel wool, aluminum foil or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean.
· DO NOT attempt to charge the battery pack with any chargers other than the ones in this manual. The charger and battery pack are specifically designed to work together.
· These chargers are not intended for any uses other than charging DEWALT rechargeable batteries. Any other uses may result in risk of fire, electric shock or electrocution.
· Do not expose charger to rain or snow.
· Pull by plug rather than cord when disconnecting charger. This will reduce risk of damage to electric plug and cord.
· Make sure that cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.
· Do not use an extension cord unless it is absolutely necessary. Use of improper extension cord could result in risk of fire,electric shock, or electrocution.
· Do not place any object on top of charger or place the charger on a soft surface that might block the ventilation slots and result in excessive internal heat. Place the charger in a position away from any heat source. The charger is ventilated through slots in the top and the bottom of the housing.
· Do not operate charger with damaged cord or plug– have them replaced immediately.
· Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way. Take it to an authorised service centre.
· Do not disassemble charger; take it to an authorised service centre when service or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.
· In case of damaged power supply cord, the supply cord must be replaced immediately by the manufacturer, its service agent or similar qualified person to prevent any hazard.
· Disconnect the charger from the outlet before attempting any cleaning. This will reduce the risk of electric shock. Removing the battery pack will not reduce this risk.
· NEVER attempt to connect two chargers together.
· The charger is designed to operate on standard 230V household electrical power. Do not attempt to use it on any other voltage. This does not apply to the vehicular charger.
Charging a Battery (Fig. B)
1. Plug the charger into an appropriate outlet before inserting battery pack.
2. Insert the battery pack 8 into the charger, making sure the battery pack is fully seated in the charger. The red (charging)

English

light will blink repeatedly indicating that the charging process has started.
3. The completion of charge will be indicated by the red light remaining ON continuously. The battery pack is fully charged and may be used at this time or left in the charger. To remove the battery pack from the charger, push the battery release button 9 on the battery pack.
nOTE: To ensure maximum performance and life of lithiumion battery packs, charge the battery pack fully before first use.
Charger Operation
Refer to the indicators below for the charge status of the battery pack.

Charge Indicators

F Charging

G Fully Charged

H Hot/Cold Pack Delay*

*The red light will continue to blink, but a yellow indicator light will be illuminated during this operation. Once the battery pack has reached an appropriate temperature, the yellow light will turn off and the charger will resume the charging procedure.
The compatible charger(s) will not charge a faulty battery pack. The charger will indicate faulty battery by refusing to light.
nOTE: This could also mean a problem with a charger.
If the charger indicates a problem, take the charger and battery pack to be tested at an authorised service centre.
hot/Cold Pack Delay
When the charger detects a battery pack that is too hot or too cold, it automatically starts a Hot/Cold Pack Delay, suspending charging until the battery pack has reached an appropriate temperature. The charger then automatically switches to the pack charging mode. This feature ensures maximum battery pack life.
A cold battery pack will charge at a slower rate than a warm battery pack. The battery pack will charge at that slower rate throughout the entire charging cycle and will not return to maximum charge rate even if the battery pack warms.
The DCB118 charger is equipped with an internal fan designed to cool the battery pack. The fan will turn on automatically when the battery pack needs to be cooled. Never operate the charger if the fan does not operate properly or if ventilation slots are blocked. Do not permit foreign objects to enter the interior of the charger.
Electronic Protection system
XR LiIon tools are designed with an Electronic Protection System that will protect the battery pack against overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic Protection System engages. If this occurs, place the lithiumion battery pack on the charger until it is fully charged.

Wall Mounting
These chargers are designed to be wall mountable or to sit upright on a table or work surface. If wall mounting, locate the charger within reach of an electrical outlet, and away from a corner or other obstructions which may impede air flow. Use the back of the charger as a template for the location of the mounting screws on the wall. Mount the charger securely using drywall screws (purchased separately) at least 25.4 mm long with a screw head diameter of 79 mm, screwed into wood to an optimal depth leaving approximately 5.5 mm of the screw exposed. Align the slots on the back of the charger with the exposed screws and fully engage them in the slots.
Charger Cleaning Instructions WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt and grease may be removed from the exterior of the charger using a cloth or soft nonmetallic brush. Do not use water or any cleaning solutions. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.
Battery Packs
Important Safety Instructions for All Battery Packs
When ordering replacement battery packs, be sure to include catalogue number and voltage.
The battery pack is not fully charged out of the carton. Before using the battery pack and charger, read the safety instructions below. Then follow charging procedures outlined.
READ ALL INSTRUCTIONS
· Do not charge or use battery in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Inserting or removing the battery from the charger may ignite the dust or fumes.
· Never force battery pack into charger. Do not modify battery pack in any way to fit into a noncompatible charger as battery pack may rupture causing serious personal injury.
· Charge the battery packs only in DEWALT chargers.
· DO NOT splash or immerse in water or other liquids.
· Do not store or use the tool and battery pack in locations where the temperature may fall below 4 °C (39.2 °F) (such as outside sheds or metal buildings in winter), or reach or exceed 40 °C (104 °F) (such as outside sheds or metal buildings in summer).
· Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The battery pack can explode in a fire. Toxic fumes and materials are created when lithiumion battery packs are burned.
· If battery contents come into contact with the skin, immediately wash area with mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture of liquid organic carbonates and lithium salts.

· Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persists, seek medical attention.
WARNING: Burn hazard. Battery liquid may be flammable
if exposed to spark or flame. WARNING: Never attempt to open the battery pack for
any reason. If battery pack case is cracked or damaged, do not insert into charger. Do not crush, drop or damage battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run over or damaged in any way (i.e., pierced with a nail, hit with a hammer, stepped on). Electric shock or electrocution may result. Damaged battery packs should be returned to
service centre for recycling. WARNING: Fire hazard. Do not store or carry the battery pack so that metal objects can contact exposed battery terminals. For example, do not place the battery pack in aprons, pockets, tool boxes, product kit
boxes, drawers, etc., with loose nails, screws, keys, etc. CAUTION: When not in use, place tool on its side on a stable surface where it will not cause a tripping or falling hazard. Some tools with large battery packs will stand upright on the battery pack but may be easily knocked over.
Transportation WARNING: Fire hazard. Transporting batteries can possibly cause fire if the battery terminals inadvertently come in contact with conductive materials. When transporting batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit. NOTE: Lithiumion batteries should not be put in checked baggage.
DEWALT batteries comply with all applicable shipping regulations as prescribed by industry and legal standards which include UN Recommendations on the Transport of Dangerous Goods; International Air Transport Association (IATA) Dangerous Goods Regulations, International Maritime Dangerous Goods (IMDG) Regulations, and the European Agreement Concerning The International Carriage of Dangerous Goods by Road (ADR). Lithiumion cells and batteries have been tested to section 38.3 of the UN Recommendations on the Transport of Dangerous Goods Manual of Tests and Criteria.
In most instances, shipping a DEWALT battery pack will be excepted from being classified as a fully regulated Class 9 Hazardous Material. In general, only shipments containing a lithiumion battery with an energy rating greater than 100 Watt Hours (Wh) will require being shipped as fully regulated Class 9. All lithiumion batteries have the Watt Hour rating marked on the pack. Furthermore, due to regulation complexities, DEWALT does not recommend air shipping lithiumion battery packs alone regardless of Watt Hour rating. Shipments of tools with batteries (combo kits) can be air shipped as excepted if the Watt Hour rating of the battery pack is no greater than 100 Wh.
Regardless of whether a shipment is considered excepted or fully regulated, it is the shipper’s responsibility to consult

English
the latest regulations for packaging, labeling/marking and documentation requirements.
The information provided in this section of the manual is provided in good faith and believed to be accurate at the time the document was created. However, no warranty, expressed or implied, is given. It is the buyer’s responsibility to ensure that its activities comply with the applicable regulations. Transporting the FlEXVOlTTM Battery The DEWALT FLEXVOLTTM battery has two modes: Use and Transport. Use Mode: When the FLEXVOLTTM battery stands alone or is in a DEWALT 18V product, it will operate as an 18V battery. When the FLEXVOLTTM battery is in a 54V or a 108V (two 54V batteries) product, it will operate as a 54V battery. Transport Mode: When the cap is attached to the FLEXVOLTTM battery, the battery is in Transport mode. Keep the cap for shipping.
When in Transport mode, strings of cells are electrically disconnected within the pack resulting in 3 batteries with a lower Watt hour (Wh) rating as compared to 1 battery with a higher Watt hour rating. This increased quantity of 3 batteries with the lower Watt hour rating can exempt the pack from certain shipping regulations that are imposed upon the higher Watt hour batteries.
For example, the Transport Example of Use and Transport Label Marking Wh rating might indicate 3 x 36 Wh, meaning 3 batteries of 36 Wh each. The Use Wh rating might indicate 108 Wh (1 battery implied).
Storage Recommendations 1. The best storage place is one that is cool and dry away
from direct sunlight and excess heat or cold. For optimum battery performance and life, store battery packs at room temperature when not in use.
2. For long storage, it is recommended to store a fully charged battery pack in a cool, dry place out of the charger for optimal results.
nOTE: Battery packs should not be stored completely depleted of charge. The battery pack will need to be recharged before use.
Labels on Charger and Battery Pack In addition to the pictographs used in this manual, the labels on the charger and the battery pack may show the following pictographs:
L Read instruction manual before use.
p See Technical Data for charging time.
11

English
q Do not probe with conductive objects. r Do not charge damaged battery packs. s Do not expose to water. t Have defective cords replaced immediately u Charge only between 4 °C and 40 °C. v Only for indoor use.
x Discard the battery pack with due care for the environment.
y Charge DEWALT battery packs only with designated DEWALT chargers. Charging battery packs other than the designated DEWALT batteries with a DEWALT charger may make them burst or lead to other dangerous situations.
z Do not incinerate the battery pack. B USE (without transport cap). Example: Wh rating
indicates 108 Wh (1 battery with 108 Wh).
A TRANSPORT (with builtin transport cap). Example: Wh rating indicates 3 x 36 Wh (3 batteries of 36 Wh).
Battery Type The following tools operate on a 18 volt battery pack: DCS565 These battery packs may be used: DCB181, DCB182, DCB183, DCB183B, DCB183G, DCB184, DCB184B, DCB184G, DCB185, DCB187, DCB189, DCB546, DCB547, DCB548. Refer to Technical Data for more information.
Package Contents
The package contains: 1 Circular saw 1 Circular saw blade 1 Hex key 1 Parallel fence 1 Dust extraction port 1 Charger (C, D, L, M, P, S, T, X, Y models) 1 LiIon battery pack (C1, D1, L1, M1, P1, S1, T1, X1, Y1 models) 2 LiIon battery packs (C2, D2, L2, M2, P2, S2, T2, X2, Y2 models) 3 LiIon battery packs (C3, D3, L3, M3, P3, S3, T3, X3, Y3 models) 1 Instruction manual nOTE: Battery packs, chargers and kitboxes are not included with N models. Battery packs and chargers are not included with NT models. B models include Bluetooth® battery packs. nOTE: The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth®, SIG, Inc. and any use of

such marks by DEWALT is under license. Other trademarks and trade names are those of their respective owners. · Check for damage to the tool, parts or accessories which may
have occurred during transport. · Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
a Read instruction manual before use. g Wear ear protection. f Wear eye protection. n Visible radiation. Do not stare into light.
Date Code Position (Fig. B) The date code 13 , which also includes the year of manufacture, is printed into the housing. Example:
2020 XX XX Year and week of Manufacture
Description (Fig. A, D) WARNING: Never modify the power tool or any part of it. Damage or personal injury could result. 1 Trigger switch lockoff button 2 Trigger switch 3 Battery pack 4 Depth adjustment lever 5 Shoe 6 Lower blade guard retracting lever 7 Lower blade guard 8 Blade clamping screw 9 Kerf indicator 10 Bevel adjustment lever 11 Worklight 12 Auxiliary handle 13 Battery release button 14 Hex key 15 Blade 16 Spindle 17 Rafter hook
Intended Use Your DCS565 cordless circular saw has been designed for professional wood sawing applications. DO nOT use under wet conditions or in the presence of flammable liquids or gases. These heavyduty circular saws are professional power tools.

DO nOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool. · Young children and the infirm. This appliance is not
intended for use by young children or infirm persons without supervision.
· This product is not intended for use by persons (including children) suffering from diminished physical, sensory or mental abilities; lack of experience, knowledge or skills unless they are supervised by a person responsible for their safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack before making any adjustments or removing/ installing attachments or accessories. An accidental
startup can cause injury. WARNING: Use only DEWALT battery packs and chargers.
Inserting and Removing the Battery Pack from the Tool (Fig. B)
nOTE: Make sure your battery pack 8 is fully charged.
To Install the Battery Pack into the Tool Handle 1. Align the battery pack 8 with the rails inside the tool’s
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool 1. Press the release button 9 and firmly pull the battery pack
out of the tool handle.
2. Insert battery pack into the charger as described in the charger section of this manual.
Fuel Gauge Battery Packs (Fig. B) Some DEWALT battery packs include a fuel gauge which consists of three green LED lights that indicate the level of charge remaining in the battery pack.
To actuate the fuel gauge , press and hold the fuel gauge button. A combination of the three green LED lights will illuminate designating the level of charge left. When the level of charge in the battery is below the usable limit, the fuel gauge will not illuminate and the battery will need to be recharged. nOTE: The fuel gauge is only an indication of the charge left on the battery pack. It does not indicate tool functionality and is subject to variation based on product components, temperature and enduser application.
Changing Blades
To Install the Blade (Fig. A, D, E) WARNING: Remove battery before service, adjustment, installing or removing accessories.
1. Place inner clamp washer 18 on saw spindle 16 with the large flat surface facing out toward the blade.

English
2. Retract the lower blade guard 7 and place blade on saw spindle against the inner clamp washer, making sure that the blade will rotate in the proper direction (the direction of the rotation arrow on the saw blade and the teeth must point in the same direction as the direction of rotation arrow on the lower blade guard). Do not assume that the printing on the blade will always be facing you when properly installed. When retracting the lower blade guard to install the blade, check the condition and operation of the lower blade guard to assure that it is working properly. Make sure it moves freely and does not touch the blade or any other part, in all angles and depths of cut.
3. Place outer clamp washer 19 on saw spindle with the large flat surface against the blade with beveled side facing out.
4. Thread blade clamping screw 8 into saw spindle by hand (screw has lefthand threads and must be turned counterclockwise to tighten).
5. Depress the blade lock button 20 while turning the saw spindle with the hex key 14 until the blade lock engages and the blade stops rotating.
6. Tighten the blade clamping screw firmly with the blade wrench.
nOTE: Never engage the blade lock while saw is running, or engage in an effort to stop the tool. Never turn the saw on while the blade lock is engaged. Serious damage to your saw will result.
To Replace the Blade (Fig. A, D, E) WARNING: Remove battery before service, adjustment, installing or removing accessories.
1. To loosen the blade clamping screw 8 , depress the blade lock button 20 and turn the saw spindle with the hex key 14 until the blade lock engages and the blade stops rotating. With the blade lock engaged, turn the blade clamping screw clockwise with the hex key (screw has lefthand threads and must be turned clockwise to loosen).
2. Remove the blade clamping screw 8 and outer clamp washer 19 only. Remove old blade.
3. Clean any sawdust that may have accumulated in the guard or clamp washer area and check the condition and operation of the lower blade guard as previously outlined. Do not lubricate this area.
4. Select the proper blade for the application (see Blades). Always use blades that are the correct size (diameter) with the proper size and shape center hole for mounting on the saw spindle. Always assure that the maximum recommended speed (rpm) on the saw blade meets or exceeds the speed (rpm) of the saw.
5. Follow steps 2 through 6 under To Install the Blade, making sure that the blade will rotate in the proper direction.
Lower Blade Guard WARNING: The lower blade guard is a safety feature which reduces the risk of serious personal injury. Never use the saw if the lower blade guard is missing, damaged, misassembled or not working

English
properly. Do not rely on the lower blade guard to protect you under all circumstances. Your safety depends on following all warnings and precautions as well as proper operation of the saw. Check lower blade guard for proper closing before each use as outlined in Further safety instructions for All saws. If the lower blade guard is missing or not working properly, have the saw serviced before using. To assure product safety and reliability, repair, maintenance and adjustment should be performed by an authorized service center or other qualified service organization, always using identical replacement parts.
Checking the Lower Guard (Fig. A)
1. Turn tool off and disconnect from power supply.
2. Rotate the lower blade guard retracting lever 6 from the fully closed position to the fully open position.
3. Release the lever and observe the guard 7 return to the fully closed position.
The tool should be serviced by a qualified service center if it:
· fails to return to the fully closed position,
· moves intermittently or slowly, or
· contacts the blade or any part of the tool in all angles and depth of cut.
Blades WARNING: To minimize the risk of eye injury, always use eye protection. Carbide is a hard but brittle material. Foreign objects in the workpiece such as wire or nails can cause tips to crack or break. Only operate saw when proper saw blade guard is in place. Mount blade securely in proper rotation before using, and always use a clean,
sharp blade. WARNING: Do not cut metal, plastic, concrete, masonry or fiber cement materials with this saw.
Do not use abrasive wheels or blades. A dull blade will cause slow inefficient cutting, overload on the saw motor, excessive splintering, and could increase the possibility of kickback. Please refer to the table below to determine the correct size replacement blade for your model saw.

Blade Diameter 61/2″ (165 mm) 61/2″ (165 mm) 61/2″ (165 mm)

Teeth

Application

18 General purpose cutting

24 Smooth woodcutting

90 Noncarbide, plywood/ vinyl siding cutting

Cutting Depth Adjustment (Fig. A, K)
1. Hold the saw firmly and loosen (clockwise) the depth adjustment lever 4 and move shoe ( 5 , Fig. A) to obtain the desired depth of cut.
2. Make sure the depth adjustment lever has been retightened (counterclockwise) before operating saw.
For the most efficient cutting action, set the depth adjustment so that onehalf tooth of the blade will project below the material to be cut. This distance is from the tip of the tooth to

the bottom of the gullet in front of it. This keeps blade friction at a minimum, removes sawdust from the cut, results in cooler, faster sawing and reduces the chance of kickback. A method for checking for correct cutting depth is shown in Figure K. Lay a piece of the material you plan to cut along the side of the blade, as shown, and observe how much tooth projects beyond the material.
Bevel Angle Adjustment (Fig. A, L)
The full range of the bevel adjustment is from 0 ° to 50 °. The quadrant is graduated in increments of 1 °. On the front of the saw is a bevel angle adjustment mechanism consisting of a calibrated quadrant and a bevel adjustment lever 10 .
To Set the Saw for a Bevel Cut 1. Loosen (counterclockwise) the bevel adjustment lever 10
and tilt shoe ( 5 , Fig. A) to the desired angle by aligning the pointer with the desired angle mark. 2. Retighten lever firmly (clockwise).
Kerf Indicator (Fig. A)
The front of the saw shoe has a kerf indicator 9 for vertical and bevel cutting. This indicator enables you to guide the saw along cutting lines penciled on the material being cut. The kerf indicator lines up with the left (inner) side of the saw blade, which makes the slot or “kerf” cut by the moving blade fall to the right of the indicator. Guide along the penciled cutting line so that the kerf falls into the waste or surplus material.
Mounting and Adjusting the Parallel Fence (Fig. P)
The parallel fence 25 is used for cutting parallel to the edge of the workpiece.
Mounting 1. Slacken the parallel fence adjustment knob 26 to allow the
parallel fence to pass. 2. Insert the parallel fence 25 in the base plate as shown. 3. Tighten the parallel fence adjustment knob 26 .
Adjusting 1. Slacken the fence adjustment knob 26 and set the parallel
fence 25 to the desired width. The adjustment can be read on the parallel fence scale. 2. Tighten the fence adjustment knob 26
Mounting the Dust Extraction Port (Fig. A, H)
Your circular saw is supplied with a dust extraction port.
To Install the Dust Extraction Port 1. Fully loosen depth adjustment lever 4 . 2. Place the shoe 5 in the lowest position. 3. Push the dust extraction port 22 onto the circular saw
body until the locks engage the dust extraction port and an audible click is heard.

Prior to Operation
· Make sure the guards have been mounted correctly. The saw blade guard must be in closed position.
· Make sure the saw blade rotates in the direction of the arrow on the blade.
· Do not use excessively worn saw blades.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations. WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack before making any adjustments or removing/ installing attachments or accessories. An accidental startup can cause injury.
Proper Hand Position (Fig. G)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown. WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the main handle 21 and one hand on the auxilliary handle 12 .
Switching On and Off (Fig. A)
For safety reasons the trigger switch 2 of your tool is equipped with a lockoff button 1 .
Press the lockoff button to unlock the tool.
To run the tool, press the trigger switch 2 . As soon as the trigger switch is released, the lockoff switch is automatically activated to prevent unintended starting of the machine.
NOTICE: Do not switch the tool ON or OFF when the saw blade touches the workpiece or other materials.
Rafter Hook (Fig. A) WARNING: To reduce the risk of serious personal injury, do not use the tool’s rafter hook to hang the tool from your body. DO NOT use the rafter hook for tethering or securing the tool to a person or object during use. DO NOT suspend
tool overhead or suspend objects from the rafter hook. WARNING: To reduce the risk of injury from the circular saw falling on operators or bystanders, make sure it is supported securely when using the rafter hook, or resting in a secure and stable location when not in use. Be sure to keep the area below clear to reduce the risk of the tool or offcut material falling and striking someone or something below.
The circular saw has a convenient rafter hook 14 that allows it to hang on a suitable, stable structure between uses. The rafter hook is not for tethering or securing the tool to a person or object during use when elevated.

English
Workpiece Support (Fig. LO) WARNING: It is important to support the work properly and to hold the saw firmly to prevent loss of control which could cause personal injury. Figure G illustrates proper hand support of the saw. Maintain a firm grip with both hands on the saw and position your body and arm to allow you to resist kickback if it occurs. ALWAYS TURN OFF TOOL AND REMOVE BATTERY BEFORE MAKING ANY ADJUSTMENTS!
Figure L shows proper sawing position. Note that hands are kept away from cutting area. To avoid kickback, DO support board or panel NEAR the cut (Fig. N). DON’T support board or panel away from the cut (Fig. O).
Place the work with its “good” side the one on which appearance is most important down. The saw cuts upward, so any splintering will be on the work face that is up when you cut it.
Cutting (Fig. N, O)
Place the wider portion of the saw shoe on that part of the workpiece which is solidly supported, not on the section that will fall off when the cut is made. As an example, Figure L illustrates the RIGHT way to cut off the end of a board. Always clamp work. Don’t try to hold short pieces by hand! (Figure O) Remember to support cantilevered and overhanging material. Use caution when sawing material from below.
Be sure saw is up to full speed before blade contacts material to be cut. Starting saw with blade against material to be cut or pushed forward into kerf can result in kickback. Push the saw forward at a speed which allows the blade to cut without laboring.
Hardness and toughness can vary even in the same piece of material, and knotty or damp sections can put a heavy load on the saw. When this happens, push the saw more slowly, but hard enough to keep working without much decrease in speed. Forcing the saw can cause rough cuts, inaccuracy, kickback, and overheating of the motor.
Should your cut begin to go off the line, don’t try to force it back on. Release the trigger switch and allow blade to come to a complete stop. Then you can withdraw the saw, sight anew, and start a new cut slightly inside the wrong one. Withdraw the saw if you must shift the cut. Forcing a correction inside the cut can stall the saw and lead to kickback.
IF SAW STALLS, RELEASE THE TRIGGER SWITCH AND BACK THE SAW UNTIL IT IS LOOSE. BE SURE BLADE IS STRAIGHT IN THE CUT AND CLEAR OF THE CUTTING EDGE BEFORE RESTARTING.
As you finish a cut, release the trigger switch and allow the blade to stop before lifting the saw from the work. As you lift the saw, the springtensioned lower blade guard will automatically close under the blade. Remember the blade is exposed until this occurs. Never reach under the work for any reason. When you have to retract the lower blade guard manually (as is necessary
for starting pocket cuts), always use the retracting lever. WARNING: When cutting thin strips, be careful to ensure that small cutoff pieces don’t hang up on the inside of the lower blade guard.
15

English
Ripping (Fig. P)
Ripping is the process of cutting wider boards into narrower strips cutting grain lengthwise. Hand guiding is more difficult for this type of sawing and the use of a DEWALT rip fence is recommended.
Pocket Cutting (Fig. Q) WARNING: Never tie the lower blade guard in a raised position. Never move the saw backwards when pocket cutting. This may cause the saw to raise up off the work surface, which could cause injury.
A pocket cut is one that is made in a floor, wall or other flat surface.
1. Adjust the saw shoe so the blade cuts at desired depth.
2. Tilt the saw forward and rest front of the shoe on material to be cut.
3. Using the lower blade guard retracting lever, retract the lower blade guard to an upward position. Lower the rear of the shoe until the blade teeth almost touch the cutting line.
4. Release the lower blade guard (its contact with the work will keep it in position to open freely as you start the cut). Remove your hand from the lower blade guard retracting lever and firmly grip the auxiliary handle 12 , as shown in Figure Q. Position your body and arm to allow you to resist kickback if it occurs.
5. Make sure blade is not in contact with cutting surface before starting saw.
6. Start the motor and gradually lower the saw until its shoe rests flat on the material to be cut. Advance saw along the cutting line until cut is completed.
7. Release the trigger switch and allow the blade to stop completely before withdrawing the blade from the material.
8. When starting each new cut, repeat the above steps.
Dust Extraction (Fig. I) WARNING: Risk of dust inhalation. To reduce the risk of personal injury, ALWAYS wear an approved dust mask.
A dust extraction port 22 is supplied with your tool.
The dust extraction port allows you to connect the tool to an external dust extractor, either using the AirLockTM system (DWV9000XJ), or a standard 35 mm dust
extractor fitment. WARNING: ALWAYS use a vacuum extractor designed in compliance with the applicable directives regarding dust emission when sawing wood. Vacuum hoses of most common vacuum cleaners will fit directly into the dust extraction outlet.
MAINTENANCE
Your power tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and
regular cleaning. WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack

before making any adjustments or removing/ installing attachments or accessories. An accidental startup can cause injury. The charger and battery pack are not serviceable.
C
Lubrication
Your power tool requires no additional lubrication.
D
Cleaning WARNING: Blow dirt and dust out of the main housing with dry air as often as dirt is seen collecting in and around the air vents. Wear approved eye protection and approved
dust mask when performing this procedure. WARNING: Never use solvents or other harsh chemicals for cleaning the nonmetallic parts of the tool. These chemicals may weaken the materials used in these parts. Use a cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.
Lower Guard The lower guard should always rotate and close freely from a fully open to fully closed position. Always check for correct operation before cutting by fully opening the guard and letting it close. If the guard closes slowly or not completely, it will need cleaning or servicing. Do not use the saw until it functions correctly. To clean the guard, use dry air or a soft brush to remove all accumulated sawdust or debris from the path of the guard and from around the guard spring. Should this not correct the problem, it will need to be serviced by an authorised service centre.
DO NOT USE WATER FEED ATTACHMENTS WITH THIS SAW. VISUALLY EXAMINE CARBIDE BLADES BEFORE USE. REPLACE IF DAMAGED.
Optional Accessories WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DEWALT recommended accessories should be used with this product. Consult your dealer for further information on the appropriate accessories.
Protecting the Environment
Separate collection. Products and batteries marked
w with this symbol must not be disposed of with normal household waste. Products and batteries contain materials that can be recovered or recycled reducing the demand for raw materials. Please recycle electrical products and batteries

according to local provisions. Further information is available at www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails to produce sufficient power on jobs which were easily done before. At the end of its technical life, discard it with due care for our environment:
· Run the battery pack down completely, then remove it from the tool.
· LiIon cells are recyclable. Take them to your dealer or a local recycling station. The collected battery packs will be recycled or disposed of properly.

English

165

DCS565

!
DEWALT. , DEWALT .

DCS565

XJ, GB, QW

1 4950

4950

165

50°

( )

2,8

/ ( ) EN6284125:

LPA (

(A) 94

)

LWA ( (A) 105

105

)

K (

(A)

)

/2 < 2,5

< 2,5

ah, W =

K =

1,5

/ , , . .
/ , : , ( ), .

o
165 DCS565
DEWALT , , , : 2006/42/EC, EN.
2014/30/EU 2011/65/EU. DEWALT , .
DEWALT.

/ , , , EN62841, . ,
. ! / . , , , / . .

, PTEEurope DEWALT, RichardKlingerStraße 11, D65510, Idstein, 07.12.2020
a : .
:
, . .

/ ()

.
DCB546 DCB547 DCB548 DCB181 DCB182 DCB183/B/G DCB184/B/G DCB185 DCB187 DCB189

V. 18/54 18/54 18/54
18 18 18 18 18 18 18

Ah
6,0/2,0 9,0/3,0 12,0/4,0
1,5 4,0 2,0 5,0 1,3 3,0 4,0

(kg)
1,05 1,46 1,44 0,35 0,61 0,40 0,62 0,35 0,54 0,54

DCB104 DCB107 DCB112
60 270 170 75* 420 270 120 540 350 22 70 45 60/40** 185 120 30 90 60 75/50** 240 150 22 60 40 45 140 90 60 185 120

DCB113
140 220 300 35 100 50 120 30 70 100

DCB115 DCB116 DCB117 DCB118 DCB132 DCB119

135* 110* 60 75* 135* X

180 150 80 120 180 X

22 22 22 22 22 45

60 60/45** 60/40** 60/40** 60 120

30 30 30 30 30 60

75 75/60** 75/50** 75/50** 75 150

22 22 22 22 22 40

45 45 45 45 45 90

60 60 60 60 60 120

* 201811475B
** 201536
: , ,
. : , , ,
. : , , .
: , , , .
.
.

: , , . , / .

«» ()

() .
1)
a ) . .
b ) , , , . , .
c ) , . .
2)
a ) . . . , .
b ) , , . , .
c ) . .
d ) .

P
, , . , , . .
e ) , . , , .
f ) , () . .
3)
a ) , , . , , . .
b ) . . , , , , , .
c ) . / , , , «.». , , .
d ) . , , .
e ) . , . .
f ) . . ,
20

. , .
g ) . , .
h ) . .
4)
a ) . . .
b ) , . , , , .
c ) , , / , . .
d ) , . .
e ) . , , , . , , . , .
f ) . ,

, , .
g ) , , . , , .
h ) . .
5)
a ) . .
b ) . .
c ) , , , , , . .
d ) , . . . . , , .
e ) . , , .
f ) . 130 °C .
g ) , .

P
.
6) a ) . .
b ) . .

a ) : . . , .
b ) . .
c ) . .
d ) . . , .
e ) , . .
f ) . .
g ) ( ). , ,

P
, .
h ) . .

· , , ;
· , , , ;
· , , .
/ ; :
a ) , . , . , , .
b ) , . , . .
c ) , . , .

d ) . . , .
e ) . , , .
f ) . .
g ) . , .

· . .
· . , , .
· . . « ». , , EN8471.
· .
· .
· . .
· , , .
· .
· .

, . :
· ;
· ;
· ;
· .

DEWALT .

. , . , .
i DEWALT EN60335; .
, DEWALT.

. , , (. ). 1 2; 30 .
.
. (. ).
· , , ,
. : . . .

P
: ()
30 A. : . , DEWALT. ,
. : .
: , , . , , . . , . ,
· , , . .
· , DEWALT. , .
· .
· , . .
· , , , , , .
· . .
· , . .

P
.
· .
· , , . .
· . , . .
· , .
· . , . .
· .
· 230 . . .
(. [Fig.] B)
1. .
2. 8 , , . . , .
3. , . , . , 9 .
: , .

. .

H *

* , , . , , , .
() () () . , .
: .
, .

, ; , . , , . .
, . , .
DCB118 . , . , . .

XR , , .
. , .

, . . ( ) 25,4 79 , , 5,5 . .
: . . . . ; .

.
. , , . .

· , , , . .
· , . , . .
· DEWALT.
· .
· 40 °C (, ).

P
· , . . .
· , . , 15 , . , : .
· , . .
, . : .
. : . , . . , (, , , ). .
. : . . , , , , . . , ,
. . : , , . , , .
: . , . ,

P
, . : .
DEWALT , , ; (IATA) , (IMDG), (ADR). 38.3 .
DEWALT , 9. , 9 100 ( ). . , , DEWALT . ( ) , 100 .
, , , .
, . , . , .
FlEXVOlTTM
DEWALT FLEXVOLTTM : .
: FLEXVOLTTM DEWALT 18 , 18 . FLEXVOLTTM 54 108 ( 54 ), 54 .
: FLEXVOLTTM , . .
, 3 ( )

1 . 3 , .

3 × 36

36 .

108 ( 1 ).

1. , , . , .
2. .
: . .

, , :

L .

p , . .
q .
r . s
.
t .
u 4 °C 40 °C.
v .

x .
y DEWALT DEWALT. , DEWALT DEWALT .
z . B ( ).
: 108 (1 108 ).
A ( ). : 3 36 (3 36 ).
DCS565 18 . : DCB181, DCB182, DCB183, DCB183B, DCB184, DCB184B, DCB185, DCB187, DCB189, DCB546, DCB547, DCB548. . .

: 1 1 1 1 1 1 ( C, D, L, M, P, S, T, X, Y) 1 ( C1, D1,
L1, M1, P1, S1, T1, X1, Y1 2 ( C2,
D2, L2, M2, P2, S2, T2, X2, Y2 3 ( C3,
D3, L3, M3, P3, S3, T3, X3, Y3 1 : , N. NT. B Bluetooth®. : Bluetooth® Bluetooth®, SIG, Inc. DEWALT . . · ,
, .

P
· .

:
a .
g . f . n . .
(. B) 13 , , . :
2020 XX XX
(. A, D, F) : . . 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
DCS565 . , , , . .
27

P
.
. .
· . , , .
· ( ) , , , , , . .
: , , / .
. : DEWALT.
(. B)
: , 8 .

1. 8 ) (. B).
2. , , .

1. 9 .
2. , , .
(P. B)
DEWALT , , .

, . , . , , .
: . , .

(. A, D, E) : , .
1. 18 16 , .
2. 7 , , ( , ). , . , . , .
3. 19 , .
4. 8 ( ).
5. 20 , 14 , .
6. .
: , . . .

(. A, D, E) : , .
1. 8 , 20 14 , . , ( , ).
2. 8 19 . .
3. , . .
4. (. « »). () . , (./) (./) .
5. 26 « », , .
: . , , , . , . , . , . , . , , .

P
(. A)
1. .
2. 14 .
3. 12 .
, :
· ,
· , ,
· .
: , . , . . , .
. : , , , .
. , , . . , .

165 165 165

18 24 90 , /

(. A, K)
1. ,

Download

Dewalt DCS565 18V XR Cordless Brushless 165mm Circular Saw Instruction Manual

Was this manual helpful?