AEG DBE5961HG 90cm Chimney Cooker Hood Stainless Steel User Manual

AEG DBE5961HG 90cm Chimney Cooker Hood Stainless Steel

FOR PERFECT RESULTS

Thank you for choosing this AEG product. We have created it to give you impeccable performance for many years, with innovative technologies that help make life simpler – features you might not find on ordinary appliances. Please spend a few minutes reading to get the very best from it.
Visit our website to:

Get usage advice, brochures, troubleshooter, service and repair information: www.aeg.com/support
Register your product for better service: www.registeraeg.com
Buy Accessories, Consumables, and Original spare parts for your appliance: www.aeg.com/shop

CUSTOMER CARE AND SERVICE

Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the following data available: Model, PNC, Serial Number.
The information can be found on the rating plate.

  • Warning / Caution-Safety information
  • General information and tips
  • Environmental information Subject to change without notice.

SAFETY INFORMATION AND INSTALLATION

WARNING!
Refer to the separate Installation Instructions booklet for Safety
Information and Installation. Read carefully the Safety chapters before any use or maintenance of the appliance.

PRODUCT DESCRIPTION

Control panel overview

  1. On / Off
  2. First motor speed
  3. Second motor speed
  4. Third motor speed
  5. Maximum motor speed
  6. Breeze function
  7. Filter reminder
  8. Hob to hood function
  9. Lamp

DAILY USE

Using the hood
Check the recommended speed according to the table below.

  • It is recommended to leave the hood operating for approximately 15 minutes after cooking.
  • The control Panel is a sensor field. Touch the symbols for 1 second to activate the functions.

To operate the hood:

  1. Turn on the appliance by pressing the symbol.
    You can now activate the functions.
  2. To activate the function touch the symbol.
  3. If needed, touch the light symbol to illuminate the cooking surface. To turn off the appliance press the symbol again.

Hob to hood function
It is an automatic function that connects the hob with a hood. Both the hob and the hood have an infrared signal communicator. Speed of the fan is defined automatically on basis of mode setting and the temperature of the hottest cookware on the hob. You can also operate the fan using the hob manually. The function can be activated from panel of the hob.
For more information how to use the function refer to the hob user manual.

Activating Maximum Motor Speed
When you press the button , the Maximum Motor Speed starts to operate for 6 minutes. After that time, the appliance returns to its previous speed settings.

CARE AND CLEANING

Cleaning the grease filter
Each filter must be cleaned at least once a month. Filters are mounted with the use of clips and pins on the opposite side.
To clean the filter:

  1. Pull the handle on the filter underneath the hood (1) and slightly tilt the front of the filter down.

Activating and deactivating the filter notification
The filter alarm reminds to change or clean the charcoal filter and clean the grease filter. The filter indicator is turned on (red) for 30 seconds if the grease filter must be cleaned. The filter indicator flashes (red) for 30 seconds if the charcoal filter must be replaced or cleaned.

Refer to filter alarm in care and cleaning chapter.

  1. Switch on the control panel.
  2. Make sure that the icons are turned off.
  3. To activate or deactivate the charcoal filter notification touch for 3 seconds.

If the charcoal filter notification is activated, the filter icon flashes (red) five times.
If the charcoal filter notification is deactivated,
The dishwasher must be set to a low temperature and a short cycle. The grease filter may discolour, it has no influence on the performance of the appliance.
the filter icon flashes (red) three times.
To mount the filters back follow the first two steps in reverse order. Repeat the steps for all filters if applicable.
Replacing the charcoal filter

WARNING!
The charcoal filter is non-washable!

The time of saturation of the charcoal filter varies depending on the type of cooking and the regularity of cleaning the grease filter.
To replace the filter:

  1. Remove the grease filters from the appliance.
    Refer to “Cleaning the grease filter” in this chapter.
  2. press the tab (1) and slightly tilt the front of the filter.
  3. To install a new filter, perform the same steps in reverse order.
    In any case, it is necessary to replace the filters at least every four months.

Filter alarm

  • Refer to activating and deactivating the filter alarm in daily use chapter.
  • Refer to cleaning the grease filter in this chapter.
  • Refer to cleaning the charcoal filter or replacing the charcoal filter (depends on filter type).

To reset the alarm:
Touch the for 3 seconds.

Replacing the lamp
This appliance is supplied with a LED lamp and separate control gear (LED driver). These parts can be replaced by a technician only. In case of any malfunction refer to “Service” in the
“Safety Instructions” chapter.

ENVIRONMENTAL CONCERNS

Recycle materials with the symbol. Put the packaging in relevant containers to recycle it. Help protect the environment and human health by recycling waste of electrical and electronic appliances. Do not dispose of appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.