SEALEY AP2200BB.V2 SERIES 6 DRAWER TOPCHEST & ROLLCAB COMBINATION Instruction Manual
Instruction Manual
AP2200BB.V2 SERIES 6 DRAWER TOP CHEST & ROLLCAB COMBINATION
6 DRAWER TOP CHEST & ROLLCAB COMBINATION WITH BALL-BEARING SLIDES
MODEL NO: AP2200BB.V2 SERIES
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this Top chest & Rollcab combination. Locate the Top chest & Rollcab combination in a suitable working area.
X DO NOT use the Top chest & Rollcab combination for any purpose other than that for which it is designed.
X DO NOT move the Top chest & Rollcab combination with drawers open.
X DO NOT open more than one drawer at the same time.
X DO NOT step on the drawers.
X DO NOT use in damp work areas.
WARNING! The warnings cautions and instructions referred to in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood that common sense and caution are factors that cannot be built into this product but must be applied by to the operator.
Introduction
The economical way to buy American PRO® Ball-Bearing quality tool chests. Supplied packed one inside the other. This mid-size combo has smooth 25mm ball-bearing slides and all the features of the professional chests, except that the roll cab is not lockable and the castors are Ø75mm. These boxes are not interchangeable with the rest of the American PRO® Ball-Bearing Range.
SPECIFICATION/FIXINGS
| Specification (W x D x H): | |
| 4 DRAWER TOP CHEST: | |
| Overall Size: | 600 x 260 x 340mm |
| Small Drawer (x3): | 510 x 225 x 35mm |
| Medium Drawer (x1): | 510 x 225 x 85mm |
| 2 DRAWER ROLLCAB: | |
| Overall Size: | 615 x 295 x 705mm |
| Medium Drawer (x2): | 515 x 275 x 65mm |
| Cupboard (x1) | 610 x 275 x 375mm |
ASSEMBLY
4.1. Remove the bolts, nuts, and washers from the base of the roll cab (fig.1), and then lift off the body to uncover the chest.
4.2. Remove the screws from the base (fig.2), and separate them from the top chest, discard the screws.
NOTE: Place protective material onto the ground to avoid damaging the back of the top chest.
4.3. Turn the roll cab upside down and place the base into position as shown in fig.3A.
NOTE: Place protective material onto the ground to avoid damaging the top of the roll cab.
4.4. Position the corner brackets (fig.3B) and secure them using bolts, washers, and nuts.
4.5. Attach the back panel to the base using two bolts, washers, and nuts.
4.6. Ensure the base is square in the roll cab and tighten all nuts fully (fig.3C).
4.7. Place the roll cab upright and place the top chest on top as shown in fig.4.
OPERATION
5.1. To lock the top chest, close all drawers, then insert one lock bar into the back slot inside the top compartment (fig.5).
Close the lid and lock it with the key.
MAINTENANCE
6.1. Periodically lubricate the drawer slides.
6.2. Clean the surfaces with a soft cloth and a mild water/ detergent solution.
6.3. Check all fixings and tighten if required.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling center, and disposed of in a manner that is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications, and component parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team at [email protected] or 01284 757505. Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk
Business Park, Bury St Edmunds, Suffolk. IP32 7AR
© Jack Sealey Limited
Original Language Version
AP2200BB.V2 Series Issue 2 (H) 19/05/22
