SEALEY HT106LED.V2 3W SMD LED HEAD & HAT TORCH User Guide

3W SMD LED HEAD & HAT TORCH
MODEL NO: HT106LED.V2

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Refer to instruction manual

SAFETY

GENERAL

Ensure the light is fully charged before initial use.
DO NOT turn the light on when it is being charged.
DO NOT shine directly into your, other person’s, or animal’s eyes.
DO NOT allow children to use the lamp.
DO NOT handle or move the light whilst it is being charged.
DO NOT use the light if you suspect that the battery or the casing is damaged.
DO NOT leave battery in a discharged state, recharge battery immediately. Before storage, fully recharge the battery, subsequently recharge the battery at least once every six months of non-use.
WARNING! To reduce the risk of burns or fire:
DO NOT attempt to open, disassemble, modify or service the battery pack.
DO NOT crush, puncture, short external contacts or dispose of in fire or water.
DO NOT expose to temperatures above 60°C (140°F).
Replace only with the battery pack designated for this product.
Recycle or dispose of used battery as stipulated by local regulation.
If the electrolyte in the cells gets on your skin, thoroughly wash with soap and water. If it gets in your eyes, rinse thoroughly with cool water and seek immediate medical attention.
WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood that common sense and caution are factors which must be applied by the operator.

INTRODUCTION

Hands-free 3W SMD LED spotlight with adjustable inclination to direct light as required. Features auto-sensor to switch on/off just by waving hand in front. Alternatively can be overridden to stay on/off by push button. Two brightness settings. Adjustable headband and foam brow for added comfort. Powered by rechargeable Lithium-Polymer 3.7V 1.5Ah battery. Supplied with micro USB charging lead.

SPECIFICATION

Model No: ………………………………………………………………. HT106LED.V2
Battery: ……………………………………………………………………..3.7V 1.5Ah Lithium-Polymer
Charging Time: …………………………………………………………4hr
LED Type: ………………………………………………………………..3W SMD
Operating Time: ……………………………………………………… 3hr @100%, 9hr @ 30%

OPERATION

CHARGING REFER TO FIG.2
  1. Connect the USB lead to the socket on the bottom of the battery, see fig.2 and a USB power socket. Turn on the power supply. The LED charging light on the bottom of the battery will light RED to show that charging has commenced.
  2. When the battery is fully charged the LED will light GREEN.
OPERATION REFER TO FIG.1
  1. Press the on/off switch once for full light, twice for 30% light and three times for flashing light.
AUTO-SENSOR REFER TO FIG.1
  1. Press the auto-sensor button once to turn it on, the button will glow red.
  2. Pass your hand in front of the sensor to turn the light on/off as required.
  3. Turn the auto-sensor function off by pressing the auto-sensor switch once.

ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling centre, and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.

BATTERY REMOVAL
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications, and component parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team on or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

01284 757500
01284 703534

www.sealey.co.uk

© Jack Sealey Limited
Original Language Version
HT106LED.V2 Issue: 4(H,3) 12/05/22