SEALEY TST10 Temporary Puncture Repair Kit Instructions

SEALEY TST10 Temporary Puncture Repair Kit

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT IS CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY

SAFETY INFORMATION FOR THE WHOLE KIT

  • WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this tool.
  • WARNING! This kit contains flammable glue. If you require a safety data sheet, contact your Sealey stockist.
  • WARNING! Familiarise yourself with the specific applications and limitations of the kit, as well as any potential hazards.
  • This kit should be used in conjunction with inspection maintenance procedures recommended in the vehicle manufacturer’s manual.
  • Ensure that the kit is correct for the task.
  • Wear the appropriate personal protective equipment for the task. A full range is available from your Sealey stockist.
  • DO NOT use the kit for any purpose other than that for which it is designed.
  • Ensure that the vehicle is properly supported with axle stands before working under the vehicle.
  • Ensure there is adequate lighting prior to using the kit. A range of inspection lamps are available from your Sealey stockist.
  • Keep children and unauthorised persons away from the working area.
  • DO NOT use the kit if any parts are damaged or missing, as this may cause failure and/or personal injury.
  • DO NOT use the kit when you are tired, or under the influence of alcohol, drugs or intoxicating medication.
  • After use, store in a safe, dry childproof area.

SAFETY INFORMATION FOR REPAIR SOLUTION
Contents of the Repair Solution do not exceed 125 ml, Hazard Statements and Precautionary Statements have been omitted from the product label.
Signal Word: DANGER
HAZARD STATEMENTS

  • Highly flammable liquid and vapour.
  • May be fatal if swallowed and enters the airways.
  • Causes skin irritation.
  • May cause drowsiness or dizziness.
  • Very toxic to aquatic life, with long-lasting effects.

PRECAUTIONARY STATEMENTS

  • Keep away from heat/sparks/open flames/hot surfaces. – No smoking.
  • Keep the container tightly closed.
  • Ground/bond container and receiving equipment.
  • Use explosion-proof electrical/ventilating/lighting equipment.
  • Use only non-sparking tools.
  • Take precautionary measures against static discharges.
  • Avoid breathing dust/fume/gas/mist/vapours/spray.
  • Use only outdoors or in a well-ventilated area.
  • Avoid release into the environment.
  • Wash hands thoroughly after use.
  • Wear protective gloves/protective clothing/eye protection/face protection.
  • Avoid release into the environment.
  • Wash hands thoroughly after use.
  • IF ON SKIN (or hair): Remove/take off immediately all contaminated clothing.
  • Rinse with water/shower.
  • In case of fire: Use powder, foam, and carbon dioxide for extinction.
  • Store in a well-ventilated place. Keep cool.
  • Keep container tightly closed
  • IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing
  • Call a POISON CENTRE or doctor/physician if you feel unwell.
  • If skin irritation occurs: Get medical advice/attention.
  • Take off contaminated clothing and wash before reuse
  • IF SWALLOWED: Immediately call a POISON CENTRE or doctor/physician.
  • DO NOT induce vomiting.
  • Collect spillage.
  • Store locked up. Dispose of contents/container in accordance with local regulation

INTRODUCTION

Ideal for repairing punctures on tubeless tyres fitted to agricultural and off-road vehicles. Can also be used as a temporary/emergency fix on cars and commercial vehicles. Allows tyre to be repaired without removing the tyre from the wheel.
Warning: Not to be used as a permanent repair for road vehicles.

SPECIFICATION

Model no:……………………………………………………………TST10
Contents:…Rasp, Insertion Needle, Repair Strips (x30), Glue

OPERATION

  1. Remove object (causing puncture) from tyre if required.
  2. Fit collar onto insertion needle by using a hex key to undo grub screw, (see fig.1).
  3. Clean/widen puncture hole with a rasp.
  4. Fit strip in the middle of the insertion needle, with 50% protruding from each end.
  5. Cover the strip with glue.
  6. Push the strip most of the way through the tyre with the insertion needle, leaving 20mm of the strip sticking out.
  7. As you pull the insertion needle back out, use your other hand to push down the collar, so that the tool nips on the strip and the strip is pulled back out of the tyre.
  8. There will now be a loop and 2 ends protruding from the tyre, that need to be cut off.
  9. Clean items in the kit and remove the protector from the insertion needle. Store kit in a safe, childproof location.

ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.

Warranty

The guarantee is 12 months from the purchase date, proof of which is required for any claim.

Address: Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR  01284 757500 01284 703534 [email protected] www.sealey.co.uk