LG MFL71683201 Air Conditioner Owner’s Manual

OWNER’S &
INSTALLATION MANUAL
AIR
CONDITIONER

Be sure to read the “Safety Precautions” before using the product.
Keep this manual in a place where anyone who uses the product can see it.
Please be careful when using this product and check it has not been altered in any way beyond its default state to prevent the occurrence of accidents ZigBee Dongle

TABLE OF CONTENTS

Thank you for using our air conditioner featuring the ZigBee application. Please only operate after reading the user guide to  enable a more trouble-free, prolonged operation

BEFORE USE OR INSTALLATION

Safety Precautions

The following safety precautions are intended to prevent unforeseen hazards or damage in advance by using the product safely and correctly.
WARNING
Failure to observe these instructions could result in death or serious injury.
CAUTION
Failure to observe these instructions could result in personal injury or property damage.

WARNING
When installing

• Please contact a service center or installation shop to install the product.
  – It may cause fire, electric shock, explosion, or injury.
• Please contact a service center or industry professional to install this product
  – It may cause fire, electric shock, explosion, or injury.
• Do not disassemble, repair or modify the product.
  – It may cause fire or electric shock.

When using

• Do not place a heating device near the product.
  – It may cause fire.
• Do not spill water inside the product.
  – It may cause electric shock or failure.
• Do not direct an electrical short circuit to this product
  – Giving a shock to the product may cause malfunction.
• Do not damage the product with a sharp and pointy object, etc.
  – It may damage the parts and cause failure.

CAUTION
When using

• Do not clean with strong solvent-based detergent. Use a soft cloth.
  – It may cause fire or product deformation.
• Do not touch with wet hands or pull the connecting cable.
  – It may cause electric shock or failure.
• If anyone other than a licensed Professional installs, repairs, or alters LG Electronics air conditioning Products, the warranty is voided.
  – All costs associated with repair are then the full responsibility of the owner.
• The warranty period is 1 year from the date of purchase.

Precautions for ZigBee dongle Installation

• It must be installed by a professional installer.
• The ZigBee thermostat should be installed within 30 meters.
  It is recommended to be installed near the product.
• Install in a place free from electromagnetic interference.
  It may cause malfunction of the product.
• If there is a wall or obstacle between the ZigBee dongle and the
  ZigBee thermostat, communication issues may occur.
• If it is attached to steel structures such as H beams, steel plates, indoor cabinets, etc., communication issues may occur
• Do not install the product in a place with high temperature or humidity such as a kitchen or bathroom.
• Install at least 1cm away from the metal panel.
• Can not use a WiFi dongle and a ZigBee dongle at the same time.
• If the user has a WiFi dongle installed, unplug it and connect the ZigBee dongle.

Note

• ZigBee dongle is equipped with Thermostat Cluster Server and Fan Control Cluster Server.
•  ZigBee thermostat should be equipped with Thermostat Cluster Client and Fan Control Cluster Client.
•  It can be used after ZigBee join and bind the process.
•  It will not work on a general thermostat without Zigbee capabilities
• ZigBee dongle is only available for Multi V Indoor is compatible.
• ZigBee dongle can be applied simultaneously with the following accessories.
  – Contact type dry contact, Central controller.
• If you use accessories other than the above, an problem may occur

ZIGBEE DONGLE INSTALLATION

Components

Installation Parts

Installation Equipment

1. Check if the indoor unit is turned off and the power of the outdoor unit is turned off.
2. Open the control box of the indoor unit.
3. Connect the USB cable to the indoor unit PCB (CN_WF).
4.  Connect the ZigBee dongle to the USB cable.
5. Install the ZigBee dongle on the flat ceiling near the indoor unit or on the corner of the indoor unit panel. (Use the included double-sided tape to fix it in place.)

Wall Mounted

4Way Ceiling Cassette

Ceiling Concealed Duct

ZIGBEE THERMOSTAT COMMISSIONING

• Use the USIM pin to press and hold the button in the hole of the ZigBee dongle for 3 seconds.
• The green LED of the ZigBee dongle blinks when commissioning start.
• Start commissioning by pressing the commissioning button on the ZigBee thermostat.
• After commissioning is completed, the green LED of the ZigBee dongle is turned on.

Note

• The ZigBee dongle only supports 2.4 GHz radiofrequency.
• The join and bind process is included in commissioning.
• Commissioning: press the button 3 seconds (commissioning timeout: 5 minutes)
• Factory reset: press the button 9 seconds
• To connect to another device after commissioning, factory reset first, start commissioning
• For the commissioning button of the ZigBee, thermostat refer to the ZigBee thermostat’s manual.
• General thermostats cannot connect to the ZigBee dongle.
• Features provided may vary by model.

CHECKLIST BEFORE REPORTING FAILURE

Checklist Before Reporting Failure

SPECIFICATIONS

Open-source software notice information

To obtain the source code under GPL, LGPL, MPL, and other open-source licenses, that is contained in this product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers, and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon email request to [email protected].
This offer is valid for a period of three years after our last shipment of this product. This offer is valid to anyone in receipt of this information.

FCC Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna. –
• Increase the separation between the equipment and the receiver. –
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications in the construction of this device that are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment should be installed and operated with a minimum distance of 20 cm (7.8 inches) between the antenna and your body.
Users must follow the specific operating instructions for satisfying RF exposure compliance.

Industry Canada Statement
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is  subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

IC Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm (7.8 inches) between the antenna and your body.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.
SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

ZigBee dongle specifications

This Page is intentionally left blank

LG Electronics Inc.
Manufacturer: LG Electronics Inc. Changwon 2nd factory, 84,
Wanam-ro, Seongsan-gu, Changwon-si,
Gyeongsangnam-do, KOREA

www.lghvac.com
www.lg.com
Copyright © 2020 LG Electronics Inc. All Rights Reserved.