Husqvarna 105 Automower User Guide

Husqvarna 105 Automower

PRODUCT OVERVIEW

For more information and instructions, read the complete Operator’s manual on the Husqvarna website (www.husqvarna.com)
PLACEMENT OF AND CONNECTING THE CHARGING STATION

  1. Place the charging station at a central position in the working area, with a lot of open space in front of the charging station and on a relatively horizontal surface.
  2. Connect the power supply’s low voltage cable to the charging station and the power supply.
  3.  Connect the power supply to a 100-240 V wall socket.
  4. Place the robotic lawn mower in the charging station to charge the battery while the boundary wire is laid. Set the main switch to position.

PLACEMENT OF THE BOUNDARY WIRE AND THE GUIDE WIRE

  1. Lay the boundary wire so that it forms a loop around the working area.
  2. Make an eyelet at the point where the guide wire will later be connected.
  3. Run the guide wire to the point on the boundary loop where the connection will be made. Avoid laying the wire at tight angles.

CONNECTING THE BOUNDARY WIRE AND THE GUIDE WIRE

  1. Narrow passages in the yard make it difficult for the robotic lawn mower to find the charging station. The robotic lawn mower can be lead to remote areas using the guide wire. The guide wire also helps the robotic lawn mower to quickly Find the charging station.
  2. Lay the guide wire under the charging station and at least 2 m / 7 ft straight out from the front edge of the charging station.
  3. Open the connectors and lay the wire ends in the recesses on each connector.
  4. Press the connectors together using a pair of pliers.
  5. Cut off any surplus boundary wire. Cut 1-2 cm / 0.4-0.8” above the connectors.
  6. Press the connectors onto the contact pins, marked AL (left) and AR (right), on the charging station. It is important that the right-hand wire is connected to the right-hand contact pin, and the left-hand wire to the left-hand pin.
  7. Fasten the connector to the contact pin marked GUIDE on the charging station.

CONNECTING THE GUIDE WIRE TO THE BOUNDARY WIRE

  1. Cut the boundary wire with a wire cutters at the centre of the eyelet that was made in step 2.2.
  2. Connect the guide wire to the boundary wire using the accompanying couplers. Press the couplers completely together with a polygrip.

STARTING AND STOPPING

STARTING

  1. Open the cover by pressing the STOP button.
  2. Set the main switch to position 1. When you do this for the first time, a start up sequence starts where you select a four digit PIN code among other things.
  3. Press the START button and close the cover.

STOPPING
Press the STOP button.

ADJUSTING THE ROBOTIC LAWN MOWER TO SUIT THE SIZE OF YOUR LAWN
The mowing results depend on mowing time. Adjust the mowing time to suit your yard using the Timer function. You decide what times during the day the robotic lawn mower is to work. The robotic lawn mower mows about 43 m² / 463 ft² per hour and day. For example; if your yard consists of 300 m²/3230 ft² of grass, the robotic lawn mower should work on average 7 hours per day.

MAINTENANCE

  1. The main switch should be in the 0 positions during all work on the robotic lawn mower’s chassis, such as cleaning or replacing the blades. Replace the blades regularly for the best mowing result.
  2. Never use a high-pressure washer or even running water to clean the robotic lawnmower. Never use solvents for cleaning.
  3. All connections to the charging station (power supply, boundary and guidewire) must be disconnected if there is a risk of a thunderstorm.
  4. Fully charge the battery at the end of the season before winter storage.

  • Green solid light Good boundary loop signal.
  • Green flashing light ECO mode is activated.
  • Blue flashing light Malfunction in the boundary loop.
  • Red flashing light Malfunction in the charging station’s antenna.
  • Red solid light Fault in the circuit board or incorrect power supply in the charging station. The fault should be rectified by an authorized service technician.
  • Yellow flashing light Guide wire not connected or malfunction in the guide wire.

What is what?

  1. Main switch
  2. STOP button
  3. Charging plates
  4. LED for function check of the boundary and guide wires
  5. Cutting height indication
  6. Display
  7. Keypad
  8. Charging station
  9. Power supply
  10. Low voltage cable
  11. Wire for boundary and guide
  12. Couplers
  13. Pegs
  14. Connectors
  15. Measurement gauge
  16. Screws for securing the charging station
  • Included in Installation kit, not included in the purchase of the robotic lawn mower.
  • The appearance of the power supply may differ depending on market.