SEALEY AS2500 Axle Stands (Pair) 2.5tonne Capacity Per Stand Instructions
SEALEY AS2500 Axle Stands (Pair) 2.5Tonne Capacity Per Stand Instructions
AXLE STANDS (PAIR) 2.5TONNE CAPACITY PER STAND
MODEL NO: AS2500
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instructions
Fit pin through both the stands collar and the centre tube
SAFETY
- WARNING!
DO NOT OVERLOAD AXLE STANDS BEYOND RATED CAPACITY. OVERLOADING CAN CAUSE DAMAGE TO, OR FAILURE OF, THE AXLE STANDS. POSITION LOAD ON CENTRE OF CRUTCH/SADDLE ONLY. ALWAYS USE STANDS IN PAIRS ON HARD LEVEL SURFACE CAPABLE OF SUSTAINING THE LOAD. USE OF STANDS ON OTHER THAN HARD LEVEL SURFACES CAN RESULT IN LOAD INSTABILITY AND POSSIBLE LOSS OF LOAD. DO NOT USE ON TARMACADAM. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN DAMAGE TO AXLE STANDS, LOSS OF LOAD RESULTING IN PROPERTY DAMAGE, SERIOUS PERSONAL INJURY OR LOSS OF LIFE.
DANGER! GREAT CARE MUST BE TAKEN TO ENSURE YOU LOWER THE VEHICLE (OR OTHER LOAD) SLOWLY AND CAREFULLY ONTO THE CENTRES OF THE CRUTCH/SADDLE OF THE AXLE STANDS.
INTRODUCTION
All steel vehicle support stand with pin and chain. Full width V-crutch for safe support of load. Manufactured to vigorous safety standards. Proven workshop quality and reliability. Sold in pairs.
SPECIFICATION
Model No: AS2500
Capacity Each: 2.5tonne (2,500 kg)
Capacity Pair: 5tonne (5,000 kg)
Minimum Working Height: 342mm
Maximum Working Height: 500mm
OPERATION
4.1. Refer to vehicle handbook for correct jacking procedure and points. Check to ensure manufacturer’s recommended jacking points are in good condition.
4.2. Position stands under recommended strong points and adjust to the required height.
- WARNING! IN THE HIGHEST POSITION BOTH ARMS OF THE ‘U’ PIN MUST PASS THROUGH THE UPPER COLUMN – THERE MUST NEVER BE MORE THAN FOUR HOLES VISIBLE ABOVE THE LOWER COLUMN (fig.1). ENSURE THAT THE ‘U’ PIN HAS PASSED RIGHT THROUGH THE UPPER AND LOWER COLUMN SO THAT BOTH ENDS ARE VISIBLE (fig.2)
Lower the load onto stands carefully and slowly. Ensure load bearing points sit in the centres of the stand crutches and that the stands are stable. Also ensure that there are no objects or persons that could impede the safe lowering of the vehicle onto the stands.
MAINTENANCE
5.1. Before each use, check that stands and stand welds are not cracked and that there are no missing or damaged parts.
5.2. Any suspect axle stand must be removed from service immediately.
5.3. Owing to the potential hazards associated with stands, do not misuse, or make any modification to, the stands or components.
5.4. It is the responsibility of the owner to ensure that the operator has read these instructions, together with the safety features on the side of the stand, and that the operator is familiar with the use and limitations of the stands.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
© Jack Sealey Limited
AS2500 Issue 7 (1,SP,F) 19/01/22