Hitachi MB170 Smart LED TV Instruction Manual

MB170 Smart LED TV

INSTRUCTION MANUAL

Some features or functions mentioned in this user manual may vary or may not be available depending on the model
you purchased.

Table of Contents
Introduction…………………………………………………… 4 Stand Installation & Wall Mounting…………………… 5 Other Connections…………………………………………. 6 Turning On/Off the TV…………………………………….. 7 Turning On/Off the TV…………………………………….. 7 TV Control & Operation…………………………………… 8 TV Control & Operation…………………………………… 9 Initial Setup Wizard………………………………………. 13
Accounts & Sign In…………………………………….20 Apps………………………………………………………..20 Device Preferences……………………………………20 Connecting to the Internet……………………………… 24 USB Recording……………………………………………. 28 Instant Recording………………………………………28 Watching Recorded Programmes ……………….28 Timeshift Recording……………………………………28 Disk Format………………………………………………28 Schedule List…………………………………………….28 CEC…………………………………………………………… 29 Google Cast………………………………………………… 29 HBBTV System……………………………………………. 30 Troubleshooting & Tips…………………………………. 30 VGA Input Typical Display Modes…………………… 31 AV and HDMI Signal Compatibility………………….. 32 Supported File Formats for USB Mode……………. 33 Video……………………………………………………….33 Audio……………………………………………………….33 Picture……………………………………………………..35 Subtitle…………………………………………………….36 Supported DVI Resolutions……………………………. 36 Disposal Information…………………………………….. 37
English – 1 –

Safety Information
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
In extreme weather (storms, lightning) and long inactivity periods (going on holiday) disconnect the TV set from the mains.
The mains plug is used to disconnect TV set from the mains and therefore it must remain readily operable. If the TV set is not disconnected electrically from the mains, the device will still draw power for all situations even if the TV is in standby mode or switched off.
Note: Follow the on screen instructions for operating the related features.
IMPORTANT – Please read these instructions fully before installing or operating
WARNING: This device is intended to be used by persons (including children) who are capable / experienced of operating such a device unsupervised, unless they have been given supervision or instruction concerning the use of the device by a person responsible for their safety. · Use this TV set at an altitude of less than 2000 meters
above the sea level, in dry locations and in regions with moderate or tropical climates. · The TV set is intended for household and similar general use but may also be used in public places. · For ventilation purposes, leave at least 5cm of free space around the TV. · The ventilation should not be impeded by covering or blocking the ventilation openings with items, such as newspapers, table-cloths, curtains, etc. · The power cord plug should be easily accessible. Do not place the TV, furniture, etc. on the power cord. A damaged power cord/plug can cause fire or give you an electric shock. Handle the power cord by the plug, do not unplug the TV by pulling the power cord. Never touch the power cord/plug with wet hands as this could cause a short circuit or electric shock. Never make a knot in the power cord or tie it with other cords. When damaged it must be replaced, this should only be done by qualified personnel. · Do not expose the TV to dripping or splashing of liquids and do not place objects filled with liquids, such as vases, cups, etc. on or over the TV (e.g., on shelves above the unit).

· Do not expose the TV to direct sunlight or do not place open flames such as lit candles on the top of or near the TV.
· Do not place any heat sources such as electric heaters, radiators, etc. near the TV set.
· Do not place the TV on the floor and inclined surfaces.
· To avoid danger of suffocation, keep plastic bags out of the reach of the babies, children and domestic animals.
· Carefully attach the stand to the TV. If the stand is provided with screws, tighten the screws firmly to prevent the TV from tilting. Do not over-tighten the screws and mount the stand rubbers properly.
· Do not dispose of the batteries in fire or with hazardous or flammable materials.
WARNING
· Batteries must not be exposed to excessive heat such as sunshine, fire or the like.
· Excessive sound pressure from earphones or headphones can cause hearing loss.
ABOVE ALL – NEVER let anyone, especially children, push or hit the screen, push anything into holes, slots or any other openings in the case.

Caution

Serious injury or death risk

Risk of electric shock Dangerous voltage risk

Maintenance

Important maintenance component

Markings on the Product

The following symbols are used on the product as a marker for restrictions and precautions and safety instructions. Each explanation shall be considered where the product bears related marking only. Note such information for security reasons.

Class II Equipment: This appliance is designed in such a way that it does not require a safety connection to electrical earth.

Hazardous Live Terminal: The marked terminal(s) is/are hazardous live under normal operating conditions.

Caution, See Operating Instructions: The
i marked area(s) contain(s) user replaceable coin or button cell batteries.

CLASS 1 LASER PRODUCT

Class 1 Laser Product: This product contains Class 1 laser source that is safe under reasonably foreseeable condi-
tions of operation.

English – 2 –

WARNING
Do not ingest the battery, Chemical Burn Hazard This product or the accessories supplied with the product may contain a coin/button cell battery. If the coin/ button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
A television may fall, causing serious personal injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions such as: · ALWAYS use cabinets or stands or mounting
methods recommended by the manufacturer of the television set. · ALWAYS use furniture that can safely support the television set. · ALWAYS ensure the television set is not overhanging the edge of the supporting furniture. · ALWAYS educate children about the dangers of climbing on furniture to reach the television set or its controls. · ALWAYS route cords and cables connected to your television so they cannot be tripped over, pulled or grabbed. · NEVER place a television set in an unstable location. · NEVER place the television set on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the television set to a suitable support. · NEVER place the television set on cloth or other materials that may be located between the television set and supporting furniture. · NEVER place items that might tempt children to climb, such as toys and remote controls, on the top of the television or furniture on which the television is placed. · The equipment is only suitable for mounting at heights 2 m. If the existing television set is going to be retained and relocated, the same considerations as above should be applied.
Apparatus connected to the protective earthing of the building installation through the MAINS connection or through other apparatus with a connection to protective earthing and to a television distribution system using coaxial cable, may in some circumstances create a fire hazard. Connection to a television distribution system has therefore to be provided through a device providing electrical isolation below a certain frequency range (galvanic isolator)

WALL MOUNTING WARNINGS
· Read the instructions before mounting your TV on the wall.
· The wall mount kit is optional. You can obtain from your local dealer, if not supplied with your TV.
· Do not install the TV on a ceiling or on an inclined wall.
· Use the specified wall mounting screws and other accessories.
· Tighten the wall mounting screws firmly to prevent the TV from fall. Do not over-tighten the screws.
Figures and illustrations in this user manual are provided for reference only and may differ from the actual product appearance. Product design and specifications may be changed without notice.

English – 3 –

Introduction
Thank you for choosing our product. You’ll soon be enjoying your new TV. Please read these instructions carefully. They contain important information which will help you get the best from your TV and ensure safe and correct installation and operation.
Features
· Remote controlled colour TV · AndroidTM operating system · Google Cast · Voice Search · Fully integrated digital terrestrial/cable/satellite TV
(DVB-T-T2/C/S-S2) · HDMI inputs to connect other devices with HDMI
sockets · USB input · Composite inputs for external devices (such as DVD
Players, PVR, video games, etc.) · Stereo sound system · Teletext · Headphone connection · Automatic programming system · Manual tuning · Sleep timer · On/Off timer · Switch off timer · Picture off function · No signal auto power off function · VGA input · Ethernet (LAN) for Internet connectivity and service
· 802.11 a/b/g/n/ac built in WLAN Support · HbbTV
Ultra HD (UHD) TV supports Ultra HD (Ultra High Definition – also known as 4K) which provides resolution of 3840 x 2160 (4K:2K). It equals 4 times the resolution of Full HD TV by doubling the pixel count of the Full HD TV both horizontally and vertically. Ultra HD contents are supported from HDMI, some of the Over-the-Top (OTT) services, USB inputs and over DVB-T2 and DVB-S2 broadcasts.
High Dynamic Range (HDR) / Hybrid LogGamma (HLG) Using this feature the TV can reproduce greater dynamic range of luminosity by capturing and then

combining several different exposures. HDR/HLG promises better picture quality thanks to brighter, more realistic highlights, more realistic colour and other improvements. It delivers the look that filmmakers intended to achieve, showing the hidden areas of dark shadows and sunlight with full clarity, colour and detail. HDR/HLG contents are supported via native and market applications, HDMI, USB inputs and over DVB-S broadcasts. When the input source is set to the related HDMI input press the Menu button and set the HDMI EDID Version option in the TV Options>Settings>Device Preferences>Inputs menu as EDID 2.0 or Auto EDID in order to watch HDR/HLG content, if the HDR/HLG content is received through an HDMI input. The source device should also be at least HDMI 2.0a compatible in this case.
Dolby Vision
Dolby VisionTM delivers a dramatic visual experience, astonishing brightness, exceptional contrast, and vivid colour, that brings entertainment to life. It achieves this stunning image quality by combining HDR and wide colour gamut imaging technologies. By increasing the brightness of the original signal and using a higher dynamic colour and contrast range, Dolby Vision presents amazing true-to-life images with stunning detail that other post-processing technologies in the TV aren’t able to produce. Dolby Vision is supported via native and market applications, HDMI and USB inputs. When the input source is set to the related HDMI input press the Menu button and set the HDMI EDID Version option in the TV Options>Settings>Device Preferences>Inputs menu as EDID 2.0 or Auto EDID in order to watch HDR/HLG content, if the HDR/HLG content is received through an HDMI input. The source device should also be at least HDMI 2.0a compatible in this case. In the Picture Mode menu two predefined picture modes will be available if Dolby Vision content is detected: Dolby Vision Bright and Dolby Vision Dark. Both allow the user to experience the content in the way the creator originally intended with different ambient lighting conditions. To change the Picture Mode setting press the Menu button while watching the Dolby Vision content and go to Picture menu. While watching Dolby Vision Content via an application, except YouTube, Netflix and Multi Media Player, you will not be able to access the Picture menu and set the Picture Mode.

English – 4 –

Stand Installation & Wall Mounting
Assembling / Removing the pedestal
Preparations
Take out the pedestal and the TV from the packing case and put the pedestal onto a work table or any other even surface.
· Use a flat and firm table or similar even surface that can support the weight of the TV.
· Do not hold the screen panel part.
· Make sure not to scratch or break the TV.
Assembling the pedestal
1. Place the pedestal on the table or similar even surface.
2. Hold the TV over the pedestal so that it coincides with the pedestal mounting point and then lower it to be mounted with its own weight. If the pedestal is not fitted properly, gently press down until the latch/es snap/s into place.
Removing the pedestal from the TV
Be sure to remove the pedestal in the following way when using the wall-hanging bracket or repacking the TV.
· Put the TV onto a work table with the screen panel down on the clean and soft cloth. Leave the pedestal protruding over the edge of the surface.
· Press the button/s on the rear side of the pedestal to release the latch/es.
· Remove the pedestal by pulling it away from the TV.
When using the wall mount bracket
Your TV is also prepared for a VESA-compliant wall mount bracket. If it is not supplied with your TV, contact your local dealer to purchase the recommended wall mount bracket.
Stand Installation & Wall Mounting
Assembling / Removing the pedestal
Preparations
Take out the pedestal(s) and the TV from the packing case and put the TV onto a work table with the screen panel down on the clean and soft cloth (blanket, etc.)
· Use a flat and firm table bigger than the TV.
· Do not hold the screen panel part.
· Make sure not to scratch or break the TV.
Assembling the pedestal

1. Place the stand(s) on the stand mounting pattern(s) on the rear side of the TV.
2. Insert the screws provided and tighten them gently until the stand is properly fitted.
Removing the pedestal from the TV Be sure to remove the pedestal in the following way when using the wall-hanging bracket or repacking the TV. · Put the TV onto a work table with the screen panel
down on the clean and soft cloth. Leave the stand(s) protruding over the edge of the surface. · Unscrew the screws that fixing the stand(s). · Remove the stand(s). When using the wall mount bracket Your TV is also prepared for a VESA-compliant wall mount bracket. If it is not supplied with your TV, contact your local dealer to purchase the recommended wallhanging bracket.
Antenna Connection
Connect the aerial or cable TV plug to the AERIAL INPUT (ANT) socket or satellite plug to the SATELLITE INPUT (LNB) socket located on the rear side of the TV. Rear side of the TV
1
LNB
ANT
2
1. Satellite 2. Aerial or cable
If you want to connect a device to the TV, make sure that both the TV and the device are turned off before making any connection. After the connection is done, you can turn on the units and use them.

English – 5 –

Other Connections

If you want to connect a device to the TV, make sure that both the TV and the device are turned off before making any connection. After the connection is done, you can turn on the units and use them.

Connector

Type

COMPONENT

Component Video
Connection (back)

Cables
VGA to Component Connection Cable

AUDIO IN SPDIF

HDMI Connection (back&side)
VGA Connection
(back)
VGA/ Component
Audio Connection
(back)
SPDIF (Optical Out) Connection
(back)

Component/VGA Audio Cable

Device

To enable VGA/Component audio, you will need to use the back audio inputs with a VGA/Component audio cable for audio connection. When using the wall mounting kit (contact your dealer to purchase one, if not supplied), we recommend that you plug all your cables into the back of the TV before mounting on the wall. Insert or remove the CI module only when the TV is SWITCHED OFF. You should refer to the module instruction manual for details of the settings. The USB inputs on the TV support devices up to 500mA. Connecting devices that have current value above 500mA may damage your TV. When connecting equipment using a HDMI cable to your TV, to guarantee sufficient immunity against parasitic frequency radiation and trouble-free transmission of high definition signals, such as 4K content, you have to use a high speed shielded (high grade) HDMI cable with ferrites.

COMPOSITE

Composite (Audio/Video) Connection
(back)

Audio Video Cable

HEADPHONE

Headphone Connection
(side)

LAN

USB Connection
(side)
CI Connection
(side)
Ethernet Connection
(back)

LAN / Ethernet Cable

CAM module

English – 6 –

Turning On/Off the TV
Connect power
IMPORTANT: The TV set is designed to operate on 220-240V AC, 50 Hz socket.
After unpacking, allow the TV set to reach the ambient room temperature before you connect the set to the mains.
Plug the power cable to the mains socket outlet. The TV will switch on automatically.
To switch on the TV from standby
If the TV is in standby mode the standby LED lights up. To switch on the TV from standby mode either:
· Press the Standby button on the remote control.
· Press the centre of the joystick on the TV in.
To switch the TV into standby
The TV cannot be switched into standby mode via joystick. Press and hold the Standby button on the remote control. Power off dialogue will appear on the screen. Highlight OK and press the OK button. The TV will switch into standby mode.
To switch off the TV
To power down the TV completely, unplug the power cord from the mains socket.
Quick standby mode
In order to switch the TV into quick standby mode either;
· Press the Standby button on the remote.
Press again to go back to operating mode.
· Press and hold the center of the joystick on the TV.
Press again to go back to operating mode.
Your TV continues to operate in the quick standby mode state, as it regularly checks for updates. This is not a malfunction, it meets the requirements for energy consumption. In order to minimize energy consumption switch your TV into standby mode as explained above.
Turning On/Off the TV
Connect power
IMPORTANT: The TV set is designed to operate on 220-240V AC, 50 Hz socket.
After unpacking, allow the TV set to reach the ambient room temperature before you connect the set to the mains.
Plug the power cable to the mains socket outlet. The TV will switch on automatically.
To switch on the TV from standby
If the TV is in standby mode the standby LED lights up. To switch on the TV from standby mode either:

· Press the Standby button on the remote control.
· Press the centre of the control switch on the TV in.
The TV will then switch on.
To switch the TV into standby
The TV cannot be switched into standby mode via control switch. Press and hold the Standby button on the remote control. Power off dialogue will appear on the screen. Highlight OK and press the OK button. The TV will switch into standby mode.
To switch off the TV
To power down the TV completely, unplug the power cord from the mains socket.
Quick Standby Mode
In order to switch the TV into quick standby mode either;
· Press the Standby button on the remote.
Press again to go back to operating mode.
· Press the centre of the control switch on the TV in and hold it down for a few seconds.
Press again to go back to operating mode.
Your TV continues to operate in the quick standby mode state, as it regularly checks for updates. This is not a malfunction, it meets the requirements for energy consumption. In order to minimize energy consumption switch your TV into standby mode as explained above.
Turning On/Off the TV
Connect power
IMPORTANT: The TV set is designed to operate on 220-240V AC, 50 Hz socket.
After unpacking, allow the TV set to reach the ambient room temperature before you connect the set to the mains.
Plug the power cable to the mains socket outlet. The TV will switch on automatically.
To switch on the TV from standby
If the TV is in standby mode the standby LED lights up. To switch on the TV from standby mode either:
· Press the Standby button on the remote control.
· Press the control button on the TV.
The TV will then switch on.
To switch the TV into standby
The TV cannot be switched into standby mode via control button. Press and hold the Standby button on the remote control. Power off dialogue will appear on the screen. Highlight OK and press the OK button. The TV will switch into standby mode.
To switch off the TV

English – 7 –

To power down the TV completely, unplug the power cord from the mains socket. Quick Standby Mode In order to switch the TV into quick standby mode either; · Press the Standby button on the remote.
Press again to go back to operating mode. · Press the control button on the TV.
Press the control button again to go back to operating mode. Your TV continues to operate in the quick standby mode state, as it regularly checks for updates. This is not a malfunction, it meets the requirements for energy consumption. In order to minimize energy consumption switch your TV into standby mode as explained above.
TV Control & Operation

P+

V+

V-

P-

Operation with the Remote Control
Press the Menu button on your remote control to display Live TV settings menu when in Live TV mode. Press Home button to display or return to the Home Screen of the Android TV. Use the directional buttons to move the focus, proceed, adjust some settings and press OK to make selections in order to make changes, set your preferences, enter a sub-menu, launch an application etc. Press Return/Back to return to the previous menu screen.
Input Selection
Once you have connected external systems to your TV, you can switch to different input sources. Press the Source button on your remote control consecutively or use the directional buttons and then press the OK button to switch to different sources when in Live TV mode. Or enter the Inputs menu on the Home Screen, select the desired source from the list and press OK.
Changing Channels and Volume
You can adjust the volume by using the Volume +/- buttons and change the channel in Live TV mode by using the Programme +/- buttons on the remote.
TV Control & Operation

The joystick allows you to control the Volume / Programme / Source and Quick Standby-On functions of the TV.

Note: The position of the joystick may differ depending on the model.

To change volume: With the back of the TV facing you, push the joystick left to increase the volume and push it right to decrease the volume.
To change channel in Live TV mode: Scroll through the stored channels by pushing the joystick up or down.
To change source in Live TV mode: Press the centre of the joystick in, the TV options menu will be displayed. Highlight Source option and press the centre of the joystick in again, the Inputs list will appear on the screen. Select the desired source by pushing the joystick up or down and press the centre of the joystick in.
To turn the TV off (Quick Standby): Press the centre of the joystick in and hold it down for a few seconds, the TV will turn into quick standby mode.
To turn the TV off (Standby): The TV cannot be switched into standby mode via joystick.
To turn on the TV: Press the centre of the joystick in, the TV will turn on.

The control switch allows you to control the Programme and Quick Standby-On functions of the TV.
Note: The position of the control switch may differ depending on the model.
To change channel in Live TV mode: Press the centre of the control switch in, the information banner will appear on the screen. Scroll through the stored channels by pushing the control switch up or down.
To turn the TV off (Quick Standby): Press the centre of the control switch in and hold it down for a few seconds, the TV will turn into quick standby mode.
To turn the TV off (Standby): The TV cannot be switched into standby mode via control switch.
To turn on the TV: Press the centre of the control switch in, the TV will turn on.
Note: Live TV settings menu OSD in Live TV mode cannot be displayed via control switch.
Operation with the Remote Control
Press the Menu button on your remote control to display Live TV settings menu when in Live TV mode.

English – 8 –

Press Home button to display or return to the Home Screen of the Android TV. Use the directional buttons to move the focus, proceed, adjust some settings and press OK to make selections in order to make changes, set your preferences, enter a sub-menu, launch an application etc. Press Return/Back to return to the previous menu screen.
Input Selection
Once you have connected external systems to your TV, you can switch to different input sources. Press the Source button on your remote control consecutively or use the directional buttons and then press the OK button to switch to different sources when in Live TV mode. Or enter the Inputs menu on the Home Screen, select the desired source from the list and press OK.
Changing Channels and Volume
You can adjust the volume by using the Volume +/- buttons and change the channel in Live TV mode by using the Programme +/- buttons on the remote.
TV Control & Operation

Input Selection
Once you have connected external systems to your TV, you can switch to different input sources. Press the Source button on your remote control consecutively or use the directional buttons and then press the OK button to switch to different sources when in Live TV mode. Or enter the Inputs menu on the Home Screen, select the desired source from the list and press OK.
Changing Channels and Volume
You can adjust the volume by using the Volume +/- buttons and change the channel in Live TV mode by using the Programme +/- buttons on the remote.

The control button allows you to control the Quick Standby-On functions of the TV.
Note: The position of the control button may differ depending on the model.
To turn the TV off (Quick Standby): Press the control button to turn the TV into quick standby mode.
To turn the TV off (Standby): The TV cannot be switched into standby mode via control button.
To turn on the TV: Press the control button, the TV will turn on.
Note: Live TV settings menu OSD in Live TV mode cannot be displayed via the control button.
Operation with the Remote Control
Press the Menu button on your remote control to display Live TV settings menu when in Live TV mode. Press Home button to display or return to the Home Screen of the Android TV. Use the directional buttons to move the focus, proceed, adjust some settings and press OK to make selections in order to make changes, set your preferences, enter a sub-menu, launch an application etc. Press Return/Back to return to the previous menu screen.
English – 9 –

Remote Control
1

4 5

Inserting the Batteries into the Remote
Remove the screw that secure the battery compartment cover on the back side of the remote control first. Lift the cover gently. Insert two 1.5V – size AAA batteries. Make sure the (+) and (-) signs match (observe correct polarity). Do not mix old and new batteries. Replace only with same or equivalent type. Place the cover back on. Then screw the cover back on again.
Standby Button
Press and hold the Standby button on the remote control. Power off dialogue will appear on the screen. Highlight OK and press the OK button. The TV will switch into standby mode. Press briefly and release to switch the TV into quick standby mode or to switch on the TV when in quick standby or standby mode.

1. Standby: Quick Standby / Standby / On 2. Numeric buttons: Switches the channel in Live TV
mode, enters a number or a letter in the text box on the screen 3. Language: Switches among sound modes (analogue TV), displays and changes audio language (digital TV, where available) 4. Home: Opens the Home Screen 5. Mute: Completely turns off the volume of the TV 6. Volume +/7. Guide: Displays the electronic programme guide in Live TV mode 8. Directional buttons: Navigates menus, setting options, moves the focus or cursor etc., sets record time and displays the subpages in Live TV-Teletext mode when pressed Right or Left. Follow the on-screen instructions. 9. OK: Confirms selections, enters sub-menus, views channel list (in Live TV mode) 10. Back/Return: Returns to previous menu screen, goes one step back, closes open windows, closes teletext (in Live TV-Teletext mode) 11. Netflix: Launches the Netflix application 12. Menu: Displays Live TV Settings menu in Live TV mode, displays available setting options such as sound and picture 13. Stop: Stops the media being played 14. Rewind: Moves frames backwards in media such as movies 15. Record: Records programmes in Live TV mode 16. Coloured Buttons: Follow the on-screen instructions for coloured button functions 17. Text: Opens and closes teletext (where available in Live TV mode) 18. Pause: Pauses the media being played, starts timeshift recording in Live TV mode Play: Starts to play selected media 19. Fast forward: Moves frames forward in media such as movies 20. MyButton1: Opens the picture mode setting menu on available sources 21. YouTube: Launches the YouTube application 22. Exit: Closes and exits from displayed Live TV Settings menus, closes running applications and/or the Home Screen and switches to last set source 23. Info: Displays information about on-screen content 24. Source: Shows all available broadcast and content sources, closes the Home Screen and switches to last set source 25. Programme +/-: Increases/Decreases channel number in Live TV mode 26. Subtitles: Turns subtitles on and off (where available)

English – 10 –

Remote Control

23 6
22 7

Inserting the Batteries into the Remote
Remove the back cover to reveal the battery compartment. You need to do the followings in order to do that:
· Place the tip of a pen or some other pointed object in the hole above the cover and press it down.
· Then press firmly on the cover and slide in the direction of the arrow.
Insert two 1.5V – size AAA batteries. Make sure the (+) and (-) signs match (observe correct polarity). Do not mix old and new batteries. Replace only with same or equivalent type. Place the cover back on.
Standby Button
Press and hold the Standby button on the remote control. Power off dialogue will appear on the screen. Highlight OK and press the OK button. The TV will switch into standby mode. Press briefly and release to switch the TV into quick standby mode or to switch on the TV when in quick standby or standby mode.

1. Standby: Quick Standby / Standby / On 2. Numeric buttons: Switches the channel in Live TV
mode, enters a number or a letter in the text box on the screen 3. Language: Switches among sound modes (analogue TV), displays and changes audio language (digital TV, where available) 4. Mute: Completely turns off the volume of the TV 5. Volume +/6. Menu: Displays Live TV Settings menu in Live TV mode, displays available setting options such as sound and picture 7. Directional buttons: Navigates menus, setting options, moves the focus or cursor etc., sets record time and displays the subpages in Live TV-Teletext mode when pressed Right or Left. Follow the on-screen instructions. 8. OK: Confirms selections, enters sub-menus, views channel list (in Live TV mode) 9. Back/Return: Returns to previous menu screen, goes one step back, closes open windows, closes teletext (in Live TV-Teletext mode) 10. Netflix: Launches the Netflix application 11. MyButton1: Turns subtitles on and off (where available) 12. Coloured Buttons: Follow the on-screen instructions for coloured button functions 13. Rewind: Moves frames backwards in media such as movies 14. Record: Records programmes in Live TV mode 15. Play/Pause button (*) 16. Play/Pause button (*) 17. Stop: Stops the media being played 18. Fast forward: Moves frames forward in media such as movies 19. Guide: Displays the electronic programme guide in Live TV mode 20. YouTube: Launches the YouTube application 21. Exit: Closes and exits from displayed Live TV Settings menus, closes running applications and/or the Home Screen and switches to last set source 22. Info: Displays information about on-screen content 23. Home: Opens the Home Screen 24. Programme +/-: Increases/Decreases channel number in Live TV mode 25. Text: Opens and closes teletext (where available in Live TV mode) 26. Source: Shows all available broadcast and content sources, closes the Home Screen and switches to last set source
(*) Play – Starts to play selected media
Pause – Pauses the media being played, starts timeshift recording in Live TV mode

English – 11 –

Remote Control
1
2
3
4 5 6 7 8 9 10 11 12 13 14 15

1. Standby: Quick Standby / Stanby / On

2. Numeric buttons: Switches the channel in Live TV mode, enters a number or a letter in the text box on the screen

3. Language: Switches among sound modes (analogue TV), displays and changes audio

language (digital TV, where available)

4. Volume +/-

5. Microphone: Activates the microphone on the remote

6. Home: Opens the Home Screen

7. Guide: Displays the electronic programme guide in Live TV mode

25 8. OK: Confirms selections, enters to sub-menus,
views channel list (in Live TV mode)

9. Back/Return: Returns to previous menu screen, goes one step back, closes open windows, closes

teletext (in Live TV-Teletext mode)

10. Netflix: Launches the Netflix application

11. Menu: Displays Live TV Settings menu in Live TV mode

23 12. Coloured Buttons: Follow the on-screen
instructions for coloured button functions

22 13. Rewind: Moves frames backwards in media such
as movies
21 14. Stop: Stops the media being played

15. Record: Records programmes in Live TV mode
20 16. Pause: Pauses the media being played,

starts timeshift recording in Live TV mode

Play: Starts to play selected media

17. Text: Opens and closes teletext (where available

in Live TV mode)

18. Fast forward: Moves frames forward in media such as movies

16 19. Source: Shows all available broadcast and
content sources in Live TV mode

20. YouTube: Launches the YouTube application

21. Exit: Closes and exits from displayed Live TV Settings menus, closes the Home Screen

22. Directional buttons: Navigates menus, setting options, moves the focus or cursor etc., sets

record time and displays the subpages in Live

TV-Teletext mode when pressed Right or Left.

Follow the on-screen instructions.

23. Info: Displays information about on-screen content

24. Programme +/-: Increases/Decreases channel number in Live TV mode

25. Mute: Completely turns off the volume of the TV

26. Subtitles: Turns subtitles on and off (where available)

English – 12 –

Standby Button Press and hold the Standby button on the remote control. Power off dialogue will appear on the screen. Highlight OK and press the OK button. The TV will switch into standby mode. Press briefly and release to switch the TV into quick standby mode or to switch on the TV when in quick standby or standby mode.
Inserting the Batteries into the Remote
Remove the screw that secure the battery compartment cover on the back side of the remote control first. Lift the cover gently. Insert two 1.5V – size AAA batteries. Make sure the (+) and (-) signs match (observe correct polarity). Do not mix old and new batteries. Replace only with same or equivalent type. Place the cover back on. Then screw the cover back on again.
To pair remote with the TV
When TV is turned on for the first time, a search for accessories will be performed before the initial setup starts. You will need to pair your remote control with your TV at this point.
Press and hold the Source button on the remote for about 5 seconds, the LED on the remote will light up. Then release the Source button, the LED will start to blink. That means the remote is in pairing mode.
Now you will wait the TV to find your remote. Select the name of your remote and press OK when it appears on the TV screen.
When the paring process was successful, the LED on the remote will go off. If the pairing process fails the remote will enter to sleep mode after 30 seconds.
Initial Setup Wizard
Note: Follow the on-screen instructions to complete the initial setup process. Use the directional buttons and the OK button on the remote to select, set, confirm and proceed.
When turned on for the first time, a search for accessories will be performed before the initial setup starts. Follow the on-screen instructions to pair your remote control (depends on the model of the remote control) and other wireless accessories with your TV. Press Back/Return button to end adding accessories and start the setup.
1.Welcome Message and Language Selection
“Welcome” message will be displayed along with the language selection options listed on the screen. Select the desired language from the list and press OK to continue.
2.Quick Setup
If you didn’t priorly connect your TV to the internet via Ethernet a screen will be displayed where you can transfer your Android phone’s WLAN network and Google Account to your TV. Highlight Continue and press OK to proceed. Follow the on-screen instructions on your TV and your phone to complete the process.

You can also skip this step by selecting Skip option. Some steps may be skipped depending on the settings made in this step.
If you did priorly connect your TV to the internet via Ethernet a message will be displayed stating that you are connected. You can choose to continue with wired connection or change the network. Highlight Change network and press OK if you want to use wireless connection instead of wired connection.
3.Network Connection
You will be directed to the next step automatically, if you connect your TV to internet via Ethernet at this point. If not, available wireless networks will be searched and listed on the next screen. Select your WLAN network from the list and press OK to connect. Enter the password using the virtual keyboard if the network is password protected. Select the Other network option from the list, if the network that you want to connect has hidden SSID.
If you prefer not to connect to the internet at this point you can skip this step by selecting Skip option. You can connect to internet later using the Network & Internet menu options in the Settings menu from the Home Screen or from the TV options menu in Live TV mode.
This step will be skipped if internet connection has been established in the previous step.
4.Sign in to your Google account
If connection succeeds, you can sign in to your Google account on the next screen. You need to be signed in to a Google account in order to use Google services. This step will be skipped if no internet connection has been established in the previous step or if you already signed in to your Google account in Quick Setup step.
By signing in, you will be able to discover new apps for videos, music and games on Google Play; get personalised recommendations from apps like YouTube; buy or rent the newest movies and shows on Google Play Movies & TV; access your entertainment and control your media. Highlight Sign In and press OK to proceed. Sign-in options are as following:
· Use your phone or computer: You can use a browser on your phone or computer to sign in. Highlight this option and press OK button. A code will be displayed on the TV screen. Make sure your phone or computer is on the same network as your TV. Open the given website (androidtv.com/setup, follow on-screen instructions for the up-to-date website url) in your phone’s or computer’s browser and enter the code you see on your TV screen into the related entry field. Then follow the instructions on your device and complete the process.
· Use your remote: Using this option you can sign in to your Google account by entering your e-mail address or phone number and your password.

English – 13 –

If you prefer not to sign in to your Google account at this point you can skip this step by selecting Skip option.
5.Terms of Service
Terms of Service screen will be displayed next. By continuing, you will agree to the Google Terms of Service, the Google Privacy Policy and the Google Play Terms of Service. Highlight Accept and press OK on the remote to confirm and proceed. You can also view Terms of Service, Privacy Policy and Play Terms of Service on this screen. To display the content an internet connection is needed. A message will be displayed mentioning the web site address on which this information can also be viewed, in case internet access is not available.
6.Location
On the next screen, you can allow or disallow Google and third party apps to use your TV’s location information. Select Yes to confirm and press OK. To skip this step without confirmation, select No and proceed by pressing the OK button. You can change this setting later using the Settings>Device Preferences>Location menu on the Home Screen.
7.Help improve Android
Automatically send diagnostic information to Google, like crash reports and usage data from your device and apps. This information won’t be used to identify you. Select Yes to confirm and press OK. To skip this step without confirmation, select No and proceed by pressing the OK button. You can change this setting later using the Settings>Device Preferences>Usage & Diagnostics menu on the Home Screen.
Information on Google services and some features of your TV will be displayed next. You can turn on personal results for Assistant by choosing the related option when prompted. Press OK consecutively to proceed.
8.Country
In the next step select your Country from the list and press OK to continue.
9.Password
Depending on the country selection you made in the previous step you may be asked to define a password (PIN) at this point. Press OK to proceed. The selected PIN cannot be 0000. This PIN will be required in order to access some menus, contents or to release locked channels, sources etc. You will have to enter it if you are asked to enter a PIN for any menu operation later.
10.Select TV Mode
In the following step of the initial setup, you can set the TV’s operation mode either as Home or as Store. Store option will configure your TV’s settings for store environment. This option is intended only for store use. It is recommended to select Home for home use.

11.Chromecast built-in always available
Select your chromecast availability preference. If set as On your TV will be detected as a Google Cast device and allow Google Assistant and other services to wake your TV up to respond to Cast commands, even when on standby mode and the screen is off.
12.Tuner Mode
Note: If you don’t want to perform a tuner scan, select one of the available options anyway. You can skip the scan at some later stage of the installation wizard. If you skip this step you can perform a channel search later using the related Channels menu options.
The next step is the selection of the tuner mode. Select your tuner preference to install channels for Live TV function. Antenna, Cable and Satellite options are available. Highlight the option that corresponds to your environment and press OK or Right directional button to proceed.
Antenna
If Antenna option is selected, the TV will search for digital terrestrial and analogue broadcasts. On the next screen highlight Scan option and press OK to start the search or select Skip Scan to continue without performing a search.
Cable
If Cable option is selected, the TV will search for digital cable and analogue broadcasts. If any, available operator options will be listed on the Select Operator screen. Otherwise this step will be skipped. You can select only one operator from the list. Highlight the desired operator and press OK or the Right directional button to proceed. On the next screen select Scan option to start a search or select Skip Scan to continue without performing a search. If Scan is selected a configuration screen will be displayed next. Scan Mode, Frequency(KHz), Modulation, Symbol Rate(Ksym/s), Network ID options may need to be set. To perform a full scan set the Scan Mode as Full/Advance if available. Depending on the selected operator and/or Scan Mode some options may not be available to be set.
Once you are done with setting available options, press the Right directional button to proceed. The TV will start to search available broadcasts.
Satellite
If Satellite option is selected, Satellite Type screen will be displayed next. Preferred Satellite and General Satellite options will be available. Select one and press OK to proceed.
Note: Preferred Satellite and General Satellite options may not be available depending on the selected country. In this case the DVBS Configuration Setting screen will be displayed after selecting the tuner mode as Satellite.
If Preferred Satellite option is selected, next screen will be Select Operator screen. You can select only

English – 14 –

one operator from the list. Highlight the desired operator and press OK or the Right directional button to proceed. Some of the following options may be preset depending on the selected operator in this step. Check the parameters before proceeding and adjust if necessary.

with setting the available options, press the Right directional button to start scan while Scan Mode or Channels is highlighted. While the search continues you can press the Back button to cancel the search. The channels that have already been found will be
stored in the channel list.

DVBS Configuration Setting screen will be displayed next. First Antenna type(*) should be set. Universal, Single Cable and Jess Singlecable options are available. Set the Antenna Type as Universal for Direct and DiSEqC satellite systems. If you set the
antenna type as Universal, press the Right directional button to proceed to the next step. If the antenna
type is set as Single Cable or Jess Singlecable, there will be three more additional options on the
DVBS Configuration Setting screen: Tuner, Band frequency and User Defined. User Defined option will be available if the Band frequency is set as User Defined. Set these options if available and press the Right directional button to proceed.

When the initial setup is completed “Complete” message will be displayed. Press OK to finish the setup.
A disclaimer of liability will be displayed on the screen. You can use Up and Down directional buttons to scroll through and read the entire text. Highlight Accept and press OK to proceed.
Home Screen will be displayed. You can highlight Live TV app and press OK to switch to Live TV mode and watch TV channels.
Home Screen

(*) This option may be named as Satellite type depending on the country selection.
After the parameters on the DVBS Configuration Setting screen are configured according to your environment the next step may be Select Satellite screen. You may be able to set up different satellites depending on the selected antenna type and operator in the previous steps. Highlight the desired satellite option and press OK to set the parameters(*). The Satellite Status of the first satellite option will be set as On. In order to configure other settings of the satellite and to enable scan this option should be set as On first. Press Back button and select next satellite you want to set. After you completed the configuration changes, press the Right directional button to proceed.
(*) If you have a Direct satellite system, DiSEqC Set option should be set as DiSEqC A.
Channel Scan screen will be displayed next. Select Scan and press OK or the Right directional button to proceed with the scanning configurations. Select Skip Scan to proceed without performing a scan and complete the initial setup.
DVBS Scan Configure screen will be displayed next if Scan option is selected. Following options will be available: Scan Mode and Channels. You can choose to perform a full scan or a network scan. Set the Scan Mode accordingly. If you are going to perfrom a network scan, make sure that you have adjusted the Frequency, Symbol Rate (Ksym/s) and Polarization parameters under the Transponder option accurately on the Select Satellite screen. You may not be able to change the Scan mode setting depending on the previous selections. If the Channels option is set as Free encrypted channels will not be installed. Additional options may also be available depending on the selected operator, configure these settings according to your preferences. Once you are done

To enjoy the benefits of your Android TV, your TV must be connected to the Internet. Connect the TV to a home network with a high-speed Internet connection. You can connect your TV wirelessly or wired to your modem/router. Refer to the Network & Internet and Connecting to the Internet sections for further information on how to connect your TV to the internet.
The Home menu is the centre of your TV. Press the Home button to display Home Screen. From the Home menu you can start any application, switch to a TV channel, watch a movie or switch to a connected device. Depending on your TV setup and your country selection in the initial setup the Home menu may contain different items.
The available options of the Home Screen are positioned in rows. To navigate through the Home Screen options use the directional buttons on the remote. Apps, YouTube, Google Play Movies & TV, Google Play Music and Google Play related rows and rows of the applications you have installed might be available. Select a row then move the focus to the desired item in the row. Press OK button to make a selection or to enter a sub-menu.
On the upper left of the screen, search tools will be located. You can choose either to type a word to start a search via the virtual keyboard or try voice search option if your remote has a built-in microphone. Move the focus to the desired option and press OK to proceed.
On the upper right of the screen, Notifications, Inputs, Network & Internet (will be named as Connected or Not Connected according to the current connection status), Settings and the current time will be displayed. You can configure your date and time preferences using the Date & time menu options from the Settings>Device Preferences menu.

English – 15 –

First row will be the Apps row. Live TV and Multi Media Player apps will be available alongside with other apps. Highlight Live TV and press OK to switch to Live TV mode. If the source was set to an option other than TV previously, press the Source button and set as TV in order to watch live TV channels. Highlight Multi Media Player and press OK to browse the connected USB devices or media servers and play/ display the installed media content on the TV. The audio files can be played through the speakers of the TV or through the speaker systems connected to the TV. You can configure your sound output preference from the Speakers option in the Settings>Device Preferences>Sound menu.
Live TV Mode Menu Content
Switch the TV to Live TV mode first and then press the Menu button on the remote to see Live TV menu options. To switch to Live TV mode you can either press the Exit button or highlight the Live TV app from the Apps row and press OK on the Home Screen.
Channels
Add to My Favorites: Add the channel that is currently being watched to the previously selected favourite list.
Program Guide: Open the electronic programme guide. Refer to the Programme Guide section for detailed information.
New Channels Available: Start a search for new channels. Select the channel source application or tuner. Then make the settings according to your environment and preferences if necessary. You can use the Channel menu options to search for broadcast channels. Refer to the Channel section for more information. When complete highlight Done and press OK.
TV Options
Source: Display the list of input sources. Select the desired one and press OK to switch to that source.
Picture Mode: Set the picture mode to suit your preference or requirements. Picture mode can be set to one of these options: User, Standard, Vivid, Sport, Movie and Game. You can use User mode to create customised settings. Go to Settings>Device Preferences>Picture for detailed setting options.
Display Mode: Set the aspect ratio of the screen. Select one of the predefined options according to your preference.
Speakers: To hear the TV audio from the connected compatible audio device set as External Audio System. Set as TV Speakers to use the speakers of your TV for sound output.

Power
Sleep Timer: Define an idle time after which you want your TV to enter sleep mode automatically.
Picture off: Select this option and press OK to turn the screen off. Press a button on the remote or on the TV to turn the screen on again. Note that you can not turn the screen on via the Volume +/-, Mute and Standby buttons. These buttons will function normally.
Switch off timer: Define a time after which you want your TV to switch off automatically. Set as Off to disable.
No Signal Auto Power Off: Set the behaviour of the TV, when no signal is detected from the currently set input source. Define a time after which you want your TV to turn itself off or set as Off to disable.
CI Card: Display available menu options of the CI card in use. This item may not be available depending on the input source setting.
Advanced Options
Audio Language: Set your language preference for audio. This item may not be available depending on the input source setting.
Blue Mute: Turn this function on/off according to your preference. When turned on, blue background will be displayed on the screen when no signal is available.
Default Channel: Set your default startup channel preference. When the Select Mode is set as User Select, Show Channels option will become available. Highlight and press OK to see channel list. Highlight a channel and press OK to make a selection. Selected channel will be displayed, every time the TV is turned back on from quick standby mode. If the Select Mode is set as Last Status, the last watched channel will be displayed.
Interaction Channel: Turn the Interaction Channel function on or off.
MHEG PIN Protection: Turn the MHEG PIN protection function on or off. This setting enables or disables access some of the MHEG applications. Disabled applications can be released by entering the right PIN.
HBBTV Settings
HBBTV Support: Turn the HBBTV function on or off.
Do Not Track: Set your preference regarding the tracking behaviour for HBBTV services.
Cookie Settings: Set your cookie setting preference for HBBTV services.
Persistent Storage: Turn the Persistent Storage function on or off. If set as On cookies will be

English – 16 –

stored with an expiry date in the persistent memory of the TV.

Version Info: Display system information such as Model Name, Version and Serial Number.

Block Tracking Sites: Turn the Block Tracking Settings: Refer to Settings section for detailed

Sites function on or off.

information.

Device ID: Turn the Device ID function on or off.
Reset Device ID: Reset the device ID for HBBTV services. Confi rmati on dialogue will be displayed. Press OK to proceed, Back to cancel.
Subtitle
Subtitle Tracks: Set your subtitle track preference, if any available.
Analog Subtitle: Set this option as Off, On or Mute. If Mute option is selected, the analogue subtitle will be displayed on the screen but the speakers will be muted simultaneously.
Digital Subtitle Language: Set one of the listed language options as first digital subtitle language preference.
2nd Digital Subtitle Language: Set one of the listed language options as second digital subtitle language preference. If the selected language in the Digital Subtitle Language option is not available, the subtitles will be displayed in this language.

Record
Record List: The recordings will be displayed if any available. Highlight a recording of your choice and press the Yellow button to delete it or press the Blue button to view detailed information. You can use Red and Green buttons to scroll the page up and down.
Device Info: Connected USB storage devices will be displayed. Highlight the device of your choice and press OK to see available options.
Set TimeShift: Tag the selected USB storage device or a partition on it for time shift recording.
Set PVR: Tag the selected USB storage device or a partition on it for PVR.
Format: Format the selected USB storage device. Refer to USB Recording section for more information
Speed Test: Start a speed test for the selected USB storage device. The test result will be displayed when completed.

Subtitle Type: Set this option as Normal or Hearing Impaired. If Hearing Impaired option is selected, it provides subtitle services to deaf and hard of hearing viewers with additional descriptions.
Teletext

Schedule List: Add reminders or record timers using the Schedule List menu.
Time Shift Mode: Enable or disable timeshift recording feature. Refer to USB Recording section for more information.

Digital Teletext Language: Set the teletext language for digital broadcasts.

Settings

Decoding Page Language: Set the decoding page language for teletext display.
BISS Key: “Click To Add Biss Key” message will be displayed. Press OK button to add a biss key. Frequency, Symbol Rate (KSym/s), Polarization, Program ID and CW Key parameters will be available to be set. Once you are done with the settings highlight Save Key and press OK to save and add the biss key. This option will not be available if the Channel Installation Mode under the Settings>Channel menu is not set as Preferred Satellite, General Satellite or Satellite. Available options will differ depending on the selected country during the initial setup process.
Auto Sleep: Define an idle time after which you want your TV to enter sleep mode automatically. 4 Hours, 6 Hours and 8 Hours options are available. Set as Never to disable.
System Information: Display detailed system information on the current channel such as Signal Level, Signal Quality, Frequency etc.

You can access the Settings menu from the Home Screen or from the TV options menu in Live TV mode.
Network & Internet
You can configure your TV’s network settings using the options of this menu. You can also highlight the Connected/Not Connected icon on the Home screen and press OK to access this menu.
Wi-Fi: Turn the wireless LAN (WLAN) function on and off.
Available networks
When the WLAN function is turned on, available wireless networks will be listed. Highlight See all and press OK to see all networks. Select one and press OK to connect. You may be asked to enter a password to connect to the selected network, in case the network is password protected. Additionally you can add new networks by using the related options.
Other options
Add new network: Add networks with hidden SSID’

Download

Hitachi MB170 Smart LED TV Instruction Manual

Was this manual helpful?