Philips PSE0501 Wireless Conference Microphone User Manual

Smart Meeting
Wireless Conference
Microphone
with Sembly Meeting
Assistant
PSE0501

User manual https://www.dictation.philips.com/pse0501help
For more support visit
www.dictation.philips.com/pse0501help

  1. Speaker
  2. USB Type-C port (input)
  3. Reset
  4. Power socket
  5. USB Type-C port (output)
  6. Microphones
  7. USB status LED
  8. Battery status LED
  9. Power
  10. Volume down
  11. Volume up
  12. . Mute
  13. Bluetooth

Connect the correct plug to the AC adapter Connect the AC adapter to the device  and a power socket The LEDs on the top of the device indicates the battery status and stop blinking  after the device is fully charged
Connect the USB cable to the “USB / OUT” port of the device and to a computer.
Note: The device can only be charged via the AC adapter		 You can now use the device with various selecting “PSE0501”
Press to turn the  device on starts blinking blue and the speaker  says “pairing” Go to the Bluetooth settings of your device and choose
“PSE0501” in the list		 stops blinking and light up blue.
The speaker says “connected”
Hold to disconnect from the current device To fully unpair go to the Bluetooth settings of your device and remove “PSE0501”
Press or to change the volume of the speaker To reset the device, press and hold the reset button on the back side of your device by using a small, pointed object, for example, a paper clip
Press to mute yourself You can use the “IN” USB Type-C port to connect a second PSE0501 device (cable not included) to further increase the range

Get your smart AI meeting assistant
Start your free trial now!

  1. Go to https://smartmeeting.sembly.ai
  2. Sign up
  3. the packaging or the device itself)
  4. Use the code “SM2022D1” to activate your Team Plus plan (unlimited

© 2022 Speech Processing Solutions GmbH. All rights reserved.
This product has been manufactured by and is sold under the responsibility of Speech Processing Solutions GmbH, and Speech Processing Solutions GmbH is the warrantor in relation to this product.
Specifications are subject to change without notice. Philips and the Philips shield emblem are registered trademarks of Koninklijke Philips N.V. and are used under license.
Document version 1.0, 03/02/22


NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  •  Increase the separation between the equipment and receiver.
  •  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Manufactured for: Speech Processing Solutions GmbH,
Gutheil-Schoder-Gasse 8-12, 1100 Wien, Osterreich
www.philips.com/dictation
Brand: Philips
Product name: Wireless Conference Microphone
Model: PSE0501
Operating temperature: 5° — 45° C / 41° —113° F
Maximum Bluetooth transmits power: +6 dBm

The product shall only be connected to a USB interface of version USB2.0 or higher. Charging via USB is not supported, the device can only be charged via the included AC adapter.

For this device, Head SAR and Body SAR were performed with the device configured in the positions according to EN62209-1:2016 & EN622092:2010, and Body SAR was performed with the device 0mm from the phantom. Body SAR was also performed with the headset attached and without.

pse0501_fcc-ce_warning-card.indd 2
03/03/2022 13:54:38