Philips CN-SBM230 Voice Amplifier Speaker User Manual

PHILIPS CN-SBM230 Voice Amplifier Speaker

WHATS IN THE BOX

OVERVIEW

  1. AUDIO IN
  2. MIC IN
  3. DISPLAY
  4. ANTENNA
  5. SOURCE
  6. HOOK
  7. USB
  8. MICRO USB
  9. TF CARD
  10. POWER ON/OFF VOL+­
  11. CHARGING INDICATOR

Power On/Off

Rotate the volume knob clockwise/anticlockwise to turn the speaker on or off.
Tips:
When the speaker is not connected with any signal source and there is no operation for 15 minutes. The speaker will automatically enter into power-saving mode. You need to switch the knob off and then switch on to wake up the speaker.

REC

Preparation for Recording 

  1. Connect the wired headset microphone to the MIC slot.
  2. Insert a USB flash disk or a TF card into the speaker.

Tips: The wired headset microphone needs to be purchased separately.

Recording Procedure

  1. Press SOURCE key to switch to Recording Mode
  2.  Press to start recording
  3. Long press to end recording and store the audio file into the USB flash disk or TF card
  4. Listen to your recordings: Press SOURCE key to switch to MP3 mode, press  to listen to your latest recording

FM Radio Mode Instructions

Search FM Radio stations automatically: Short press SOURCE key to select FM source. When you enter FM radio mode for the first time, press and hold key for two seconds to scan and save stations automatically. Press to switch to previous or next station. Search FM Radio stations manually: In FM Radio Mode, press and hold  key for two seconds, When the display frequency is blinking. press to switch to your favorable station, press key to save it. Press and hold key for 2 seconds to exit. Clear the radio station: In FM mode, long press SOURCE button for 5 seconds, it will clear all radio stations, and at the same time there will be voice prompts

UHF Wireless Microphone Instructions

  1. When first time pairing. Turn on the UHF wireless microphone, press and hold PAIR key for 5~6 seconds.after blinking blue, UHF enters the pairing search (as shown in Fig.1), and then power on the speaker(as shown in Fig.2), when the UHF icon on display keep solid from blinking means paired successfully (as shown in Fig.3), Now you can wear the UHF wireless microphone to speak (as shown in Fig.4). Please adjust the volume to avoid howling according to the space of environment.
  2. Once paired successfully. next time.the UHF microphone will pair automatically when power on.Please refers to the step 1 above when there is a new UHF wireless microphone or new speaker.
  3. When there are many people using same device in the same place. occasionally appear string frequency phenomenon.or can not connect. press PAIR key on the microphone for the frequency changes.
  4. Charging instructions of UHF wireless microphone. Blinking orange while battery low, please charge in time. Solid red while charging, and red off after full charged. (Lock Touch Key: double press the SOURCE key quickly to lock the touch operation.You will hear a voice prompt. Unlock Touch Key: double press the SOURCE key again to unlock the touch operation.You will hear twice voice prompt. The touch key will be automatically locked after 20 seconds with no operation in the wireless or wireless microphone mode.)

AUDIO IN Mode

Connect your Audio in cable to the AUDIO IN socket, there will be voice prompts and the speaker will enter into the AUDIO IN mode automatically.

Bluetooth Mode Instructions

  1. Press SOURCE key to switch to Bluetooth pairing mode. The bLUE icon blinking on the screen and there is a voice prompt.
  2. Activate Bluetooth of your phone or device, scan for “Philips SBM230”, click and connect successfully, the bLU E icon keep solid on the screen, and there is a voice prompt that the Bluetooth is connected.

Specifications

  • Rated Output Power 3W RMS
  • Signal to Noise Ratio S0dBA
  • Aux Input 600mV RMS, 22 kohm
  • Power Supply sv= o.sA
  • Built-in Battery lithium battery
  • Dimensions – Main Unit (W x H x D) 90 x 116 x 32 mm
  • Weight -Main Unit 0.198kg

Warning 

  • Never remove the casing of this apparatus.
  • Never lubricate any part of this apparatus.
  • Never place this apparatus on other electrical equipment.

Notice
Any Changes or modifications made to this device that are not expressly approved by MMD Hong Kong Holding Limited may void the user’s authority to operate the equipment.
Disposal of your old product
Your product is designed and manufactured with high quality materials and components.which can be recycled and reused. Do not throw away the product with the normal household waste at the end of its life.but hand it in at an official collection point or recycling.By doing this.you help to preserve the environment.

Caution 
Removal of the built-in battery invalidates the warrantty and may destroy the product. Environmental information All unnecessary packaging has been omitted.We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags,protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials.exhausted batteries and old equipment.

Note 
The type plate is located on the bottom of the apparatus.

MP3 Mode Instructions

Set loop one/loop all playing: In MP3 mode.the default setting is loop all. If you want to play current track repeatedly, press and hold  for 2 seconds while playing.and there will be voice prompts to tell you the loop one function has been enabled.To enable the loop all function.press and hold for 2 seconds again, there will be voice prompts to tell you the loop all function has been enabled.USB flash disk and TF card support 32GB max. Audio format: support MP3 / WMA / WAV (sampling frequency 8k~48k)

Safety

Important Safety Instructions 

  • Heed all warnings.
  • Follow all instructions.
  • Do not use this apparatus near water.
  • Do not block any ventilation openings.Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves,or other devices (including amplifiers) that produce heat.
  • Only use attachments/accessories specified by the manufacturer.
  • Refer all servicing to qualified service personnel. Servicing is required when the device has been damaged in any way.such as the power-supply cord or plug is damaged.liquid has been spilled or objects have fallen into the device.the device has been exposed to rain or moisture.does not operate normally.or has been dropped.
  • Devices shall not be exposed to dripping or splashing.
  • Do not place any sources of danger on the device(e.g. liquid filled objects. or lighted candles).