SEALEY LED2105F Cordless 21+5 Rechargeable Inspection Lamp Lithium-Ion Hi-Vis Instructions
INSTRUCTIONS FOR
CORDLESS 21+5 RECHARGEABLE INSPECTION LAMP LITHIUM-ION HI-VIS
MODEL NO: LED2105F
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. GENERAL
DO NOT LEAVE BATTERY IN A DISCHARGED STATE, RECHARGE BATTERY IMMEDIATELY. BEFORE STORAGE, FULLY RECHARGE THE BATTERY, SUBSEQUENTLY RECHARGE THE BATTERY AT LEAST ONCE EVERY SIX MONTHS OF NON-USE.
1.2. ELECTRICAL SAFETY FOR USE OF CHARGER.
USE ONLY THE SUPPLIED CHARGER PLUG FOR CONNECTING LAMP TO THE POWER SUPPLY.
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices.
An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD (Residual Current Device) is used with all electrical products, particularly portable equipment which is plugged into an electrical supply not protected by an RCCB.
You must also read and understand the following instructions concerning electrical safety.
1.2.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.2.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.2.3. You must ensure that you:
1.3 BATTERY SAFETY
If the electrolyte in the cells gets on your skin, thoroughly wash with soap and water. If it gets in your eyes, rinse thoroughly with cool water and seek immediate medical attention
2. INTRODUCTION
Model No’s LED2105, LED2105F, LED2105G and LED2105UV feature 26 super bright LEDs and Model No. LED3010 features 35 super bright LEDs for use as inspection lamps. All models have 5 LEDs in the end for use as a directional torch. Model No. LED2105UV has five Ultra Violet LEDs for fault finding with fluorescent dyes used in leak detection. Single LED battery indicator. Two 360° swivel hanging hooks for hands-free applications. Three rubber covered magnets, two magnets on the rear of the lamp and one on the end. Bottom quarter of the lamp rotates 180°. Replaceable shatterproof polycarbonate lens with a highly polished reflector board gives an increased spread of light. Lithium-ion polymer battery for longer life, no memory effect and a much slower discharge than typical Ni-MH batteries. Supplied with mains and in-car chargers. Model No. LED2105 available with Schuko plug, add EU to Model No.
3. SPECIFICATION
Model No:…………………… LED2105F
Charging Time:………………. 4hrs
Operating Time: …………….. 4hrs
4. CHARGING
the battery fitted to this cordless tool is considered to be a consumable item and its ability to accept a charge will reduce over time. We will warranty it against mechanical and electrical defect for a period of one year – this does not cover fair wear and tear. If the battery is not properly charged before first use, or regularly conditioned, its capacity will diminish. Under these circumstances we will not replace the battery even if it is less than one year old.
Note: fully charge the battery before first use.
Note: The Lithium battery does not suffer from memory effect and once fully charged may be stored for up to six months without another charge.
4.1. Connect the charger into the charge socket on back of the lamp (Fig.2A). Plug into power supply and turn on, the charging LED (Fig.1A) on the lamp will light RED to show charging has commenced.
5. OPERATION
5.1. Direct the lens away from your eyes before switching on.
5.2. Toggle the lamp between 5 LED, 21 LED and OFF using the push switch on the handle (Fig.1B).
5.3. Suspend the lamp by the hanging hooks. When the light is hanging from one hook it can be rotated through 360° for more precise positioning.
5.4. Alternatively use the integral magnets to attach the lamp to any ferrous surface.
6. MAINTENANCE
6.1. To replace the shatter proof lens, use a small screwdriver to prise the lens off through the gap between the rubber ON / OFF switch and lens. Gently flex the lens to remove it completely.
6.2. When replacing the lens insert the top tab in first and bend the lens to insert the bottom, snap the rest of the lens into the lamp.
Note: LED arrays are designed to allow individual LEDs to cease functioning without causing the entire array to fail. This could be as a result of shock or impact. Shock or impact will invalidate the warranty.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal dispose according to local regulations.
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.
Remove the 8 screws on the back of the lamp. Remove the back casing and disconnect the wiring to the charger port and from the battery in the circuit board. Dispose of according to local government guidelines.
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk.
IP32 7AR
© Jack Sealey Limited Original Language Version LED2105F | Issue 3(I) 17/03/15