SEALEY SPI1S Intelligent Speed Charger Battery Charger Instruction Manual

 SEALEY SPI1S Intelligent Speed Charger Battery Charger

WARNING
READ THE ENTIRE MANUAL BEFORE USING THIS PRODUCT. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH

SAFETY AND INSTRUCTION

SAVE THESE INSTRUCTIONS
 This manual will show you how to use your charger safely and effectively. Please read, understand and follow these instructions and precautions carefully, as this manual contains important safety and operating instructions. The safety messages used throughout this manual contain a signal word, a message and an icon. The signal word indicates the level of the hazard in a situation. Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury to the operator or bystanders. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury to the operator or bystanders. Indicates a potentially hazardous situation which, if not avoided, could result in moderate or minor injury to the operator or bystanders. Indicates a potentially hazardous situation which, if not avoided, could result in damage to the equipment or vehicle or property damage.

1. Children should be supervised to ensure that they do not play with the appliance. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
2. This charger is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the charger by a person responsible for their safety. Children should be supervised to ensure they do not play with the charger
3. Use only recommended attachments. Use of an attachment not recommended or sold by Sealey risk of fire, electric shock or injury to persons or damage to property.
4. To reduce the risk of damage to the electric plug or cord, pull by the plug rather than the cord when disconnecting the charger.
5. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in a risk of fire and electric shock. If an extension cord must be used
6. To reduce the risk of electric shock, unplug the charger from the outlet
   before attempting any maintenance or cleaning. Simply turning off the
   controls will not reduce this risk.
7. Do not operate the charger with a damaged cord or plug. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
8. Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in any way; take it to a qualified service person
9. Do not disassemble the charger; take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a  risk of fire or electric shock. RISK OF EXPLOSIVE GASES. 1.12 WORKING IN THE VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORT ANCE THAT YOU FOLLOW THE INSTRUCTIONS EACH TIME YOU USE THE CHARGER.
10. To reduce the risk of a battery explosion, follow these instructions and those published by the battery manufacturer and the manufacturer of any equipment you intend to use in the vicinity of the battery. Review the cautionary markings on these products and on the engine.

PERSONAL PRECAUTIONS

RISK OF EXPLOSIVE GASES.

1. NEVER smoke or allow a spark or flame in the vicinity of a battery or engine.
2. Remove personal metal items such as rings, bracelets, necklaces and watches when working with a lead-acid or lithium ion battery. These batteries can produce a short-circuit current high enough to weld a ring or the like to metal, causing a severe burn.
3. Be extra cautious, to reduce the risk of dropping a metal tool onto the battery. It might spark or short-circuit the battery or other electrical part that may cause an explosion. Use this charger for charging only 6 and 12V lead-acid, calcium, gel and AGM-type rechargeable batteries with rated capacities of 1.2-50Ah. It is not intended to supply power to a low voltage electrical system other than in a starter-motor application. Do not use this battery charger for charging dry-cell batteries that are commonly used with home appliances or lithium ion batteries used in cell phones, laptops, power tools, etc. These batteries may burst and cause injury to persons and damage to property.
4. NEVER charge a frozen battery.
5. Consider having someone nearby to come toV your aid when you work near a lead-acid battery.
6. Have plenty of fresh water and soap nearby, in case battery acid contacts your skin, clothing or eyes. Wear complete eye and body protection, including safety goggles and protective clothing. Avoid touching your eyes while working near  If battery acid contacts your skin or clothing, immediately wash the area with soap and water. If acid enters your eye, immediately flood the eye with cold running water for at least 10 minutes and get medical attention right away.
7. If battery acid is accidentally swallowed, drink milk, the whites of eggs or water. DO NOT induce vomiting. Seek medical attention immediately

PREPARING TO CHARGE

1. If it is necessary to remove the battery from the vehicle to charge it, always remove the grounded terminal first. Make sure all of the accessories in the vehicle are off, to prevent arcing.
2. Be sure the area around the battery is well ventilated while the battery is being charged.
3. Clean the battery terminals before charging the battery. During cleaning, keep airborne corrosion from coming into contact with your eyes, nose and mouth. Use baking soda and water to neutralize the battery acid and help eliminate airborne corrosion. Do not touch youreyes, nose or mouth.
4. Add distilled water to each cell until the battery acid reaches the level specified by the battery manufacturer. Do not overfill. For a battery without removable cell caps, such as valve regulated lead acid batteries (VRLA), carefully follow the manufacturer’s recharging instructions.
5. Read, understand and follow all instructions for the charger, battery, vehicle and any equipment used near the battery and charger. Study all of the battery manufacturer’s specific precautions while charging and recommended rates of charge.
6. Determine the voltage of the battery by referring to the vehicle owner’s manual and make sure that the output voltage selector switch is set to the correct voltage. If the charger has an adjustable charge rate, charge the battery in the lowest rate first.
7. Make sure that the charger cable clips make tight connections.

CHARGER LOCATION

RISK OF EXPLOSION AND CONTACT WITH BATTERY ACID.

1. Locate the charger as far away from the battery as the DC cables permit.
2. Never place the charger directly above the battery being charged; gases from the battery will corrode and damage the charger.
3. Do not set the battery on top of the charger.
4. Never allow battery acid to drip onto the charger when reading the electrolyte specific gravity or filling the battery.
5. Do not operate the charger in a closed-in area or restrict the ventilation in any way.

DC CONNECTION PRECAUTIONS

1. Connect and disconnect the DC output connectors only after removing the AC plug from the electrical outlet. Never allow the connectors to touch each other.
2. Attach the connectors to the battery and chassis, as indicated in sections 6 and 7.

FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN THE VEHICLE

A SPARK NEAR THE BATTERY MAY CAUSE A BATTERY EXPLOSION. TO REDUCE THE RISK OF A SPARK NEAR THE BATTERY

1. Position the AC and DC cables to reduce the risk of damage by the hood, door and moving or hot engine parts. NOTE: If it is necessary to close the hood during the charging process, ensure that the hood does not touch the metal part of the battery connectors or cut the insulation of the cables.
2. Stay clear of fan blades, belts, pulleys and other parts that can cause injury.
3. Check the polarity of the battery posts. The POSITIVE (POS, P, +) battery post usually has a larger diameter than the NEGATIVE (NEG, N, -) post. Determine which post of the battery is grounded (connected) to the chassis. The battery terminal not connected to the chassis has to be connected first. The other connection is to be made to the chassis, remote from the battery and fuel line. See steps 6.5 and 6.6. The battery charger is then to be connected to the supply mains. The connection to the supply mains is to be in accordance with the national wiring rules. For a negative-grounded vehicle, connect the POSITIVE (RED) connector from the battery charger to the POSITIVE (POS, P, +) ungrounded post of the battery. Connect the NEGATIVE (BLACK) connector to the vehicle chassis or engine block away from the battery. Do not connect the connector to the carburetor, fuel lines or sheet-metal body parts. Connect to a heavy gauge metal part of the frame or engine block.
4. For a positive-grounded vehicle, connect the NEGATIVE (BLACK) connector from the battery charger to the NEGATIVE (NEG, N, -) ungrounded post of the battery. Connect the POSITIVE (RED) connector to the vehicle chassis or engine block away from the battery. Do not connect the connector to the carburetor, fuel lines or sheet-metal body parts. Connect to a heavy gauge metal part of the frame or engine block.
5. Connect charger AC supply cord to electrical outlet.
6. After charging, disconnect the battery charger from the supply mains. Then remove the chassis connection and then the battery connection.
7. See Operating Instructions for length of charge information

FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE OF THE VEHICLE

1. Check the polarity of the battery posts. The POSITIVE (POS, P, +) battery post usually has a larger diameter than the NEGATIVE (NEG, N, -) post.
   6.2 Attach at least a 24-inch (61 cm) long 7 AWG (10 mm2) insulated battery cable to the NEGATIVE (NEG, N, -) battery post.
   6.3 Connect the POSITIVE (RED) charger connector to the POSITIVE (POS, P, +) post of the battery.
   6.4 Position yourself and the free end of the cable you previously attached to the NEGATIVE (NEG, N, -) battery post as far away from the battery as possible – then connect the NEGATIVE (BLACK) charger connector to the free end of the cable.
2. Do not face the battery when making the final connection.
3. Connect charger AC supply cord to electrical outlet.
4. When disconnecting the charger, always do so in the reverse order of the connecting procedure and break the first connection while as far away from the battery as practical.
5. A marine (boat) battery must be removed and charged on shore. To charge it onboard requires equipment specially designed for marine use

ASSEMBLY INSTRUCTIONS

Remove all cord wraps and uncoil the cables prior to using the battery charger.

FEATURES

1. Hook attachment
2. Charging status LED
3. Bad Battery LED
4. Power LED
5. Clamps Reversed LED
6. Battery clamps (quick-connect)
7. Ring connectors (quick-connect)

CONTROL PANEL

LED INDICATORS
POWER (green) LED lit: The charger is connected to AC power.

CHARGING INDICATOR :
Yellow/orange LED lit: The charger is charging the battery. Yellow/orange LED flashing: The charger is in abort mode. Green LED pulsing: The battery is fully charged and the charger

maintain mode.
CLAMPS REVERSED (red) LED flashing: The connections are reversed. BAD BATTERY (red) LED lit: The charger has detected a problem with the battery. See Troubleshooting for more information.

NOTE: See Operating Instructions for a complete description of the charger modes

OPERATING INSTRUCTIONS

NOTE: This charger is equipped with an auto-start feature. Current is supplied to the battery clamps before a battery is connected, and the clamps may spark if touched together.

Battery Information
This charger can be used with 3-celled (6V) and 6-celled (12V) lead-acid batteries with rated capacities of 12Ah (6V) and 1.2-50Ah (12V).

CHARGING A BATTERY IN THE VEHICLE

1. Turn off all the vehicle’s accessories.
2. Keep the hood open.
3. Clean the battery terminals.
4. Place the charger on a dry, non-flammable surface, or use the convenient hook attachment to hang the unit safely outside the work area.
5. Lay the AC/DC cables away from any fan blades, belts, pulleys and other moving parts.
6. Connect the battery, following the precautions listed in sections 6 and 7.
7. Connect the charger to a live grounded 230V AC outlet.
8. The green POWER LED will light.
9. When charging is complete, disconnect the charger from the AC power, remove the clamps from the vehicle’s chassis, and then remove the clamp from the battery terminal

CHARGING A BATTERY OUTSIDE OF THE VEHICLE

1. Place battery in a well-ventilated area.
2. Clean the battery terminals.
3. Connect the battery, following the precautions listed in sections 6 and 7.
4. Connect the charger to a live grounded 230V AC outlet.
5. The green POWER LED will light.
6. When charging is complete, disconnect the charger from the AC power, disconnect the negative clamp, and finally the positive clamp.
7. A marine (boat) battery must be removed and charged on shore. Using The Quick-Connect Cable Connectors Connect either of the two (2) output cable leads to the charger. Make sure to place the charger on a dry, non-flammable surface

Using the 50 Amp Battery ClAMps

1. Connect the end of the charger output cable to the end of the battery cable quick-connect and clamps.
2. Follow the steps in sections 6 and 7, to connect the output clamps to the battery.
3. Connect the charger to a live grounded 230V AC outlet.

Using the RING CONNECTORS

1. To permanently attach to a battery, loosen and remove each nut from the bolt at the battery terminal.
2. Connect the red POSITIVE connector ring to the POSITIVE battery terminal.
3. Connect the black NEGATIVE connector ring to the NEGATIVE battery terminal.
4. Replace and tighten the nuts to secure.
5. Connect the cable to the end of the charger output cord. Take care to keep the wires and plug away from metal and moving parts.
6. Connect the charger to a live grounded 230V AC outlet.

BATTERY CHARGING TIMES
CCA = Cold Cranking Amps Ah = Amp Hour

MAINTENANCE AND CARE

1. Clean the clamps each time you are finished charging. Wipe off any battery fluid that may have come in contact with the clamps, to prevent corrosion.
2. Occasionally cleaning the case of the charger with a soft cloth will keep the finish shiny and help prevent corrosion.
3. Coil the input and output cords neatly when storing the charger. This will help prevent accidental damage to the cords and charger.
4. Store the charger unplugged from the AC power outlet, in an upright position.
5. Store inside, in a cool, dry place. Do not store the clamps on the handle, clipped together, on or around metal, or clipped to the cables.

DISPOSAL INFORMATION

Do not dispose of this product with other household waste. To prevent possible harm to the environment or human health from uncontrolled waste disposal, and to promote the sustainable reuse of material resources, recycle it responsibly. To discard your used device, please use the return and collection systems or contact the retailer where the product was purchased, for environmentally-safe recycling.

TROUBLESHOOTING