SEALEY LED138 10W SMD LED 1000LM Under-Bonnet Cordless Rechargeable Light Instructions
CORDLESS RECHARGEABLE LIGHT
MODEL NO: LED138
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
SAFETY
1.1. GENERAL
Χ DO NOT turn the lamp on when it is being charged.
Χ DO NOT shine directly into your, another person’s or an animal’s eyes.
Χ DO NOT allow children to use the lamp.
Χ DO NOT leave the battery in a discharged state. Recharge the battery immediately.
WARNING! Ensure Health and Safety, local authority, and general workshop practice regulations are adhered to when using this light.
Wear eye protection. A full range of safety equipment is available from your Sealey stockist.
Χ DO NOT wear jewelry and tie back long hair.
1.2. ELECTRICAL SAFETY FOR USE OF CHARGER.
USE ONLY THE SUPPLIED CHARGER PLUG FOR CONNECTING THE LAMP TO THE POWER SUPPLY.
WARNING! It is the user’s responsibility to read, understand and comply with the following electrical instructions:
You must ensure the risk of electric shock is minimized by the installation of appropriate safety devices.
An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD
(Residual Current Device) is used with all electrical products, particularly portable equipment which is plugged into an electrical supply not protected by an RCCB.
You must also read and understand the following instructions concerning electrical safety.
1.2.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.2.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.2.3. You must ensure that you:
Inspect the charger plug, cable, and connector for wear and damage to ensure items are safe before connecting to the main power supply.
1.2.1. If worn or damaged DO NOT use.
IMPORTANT: Check that the voltage marked on the charger plug is the same as the lamp.
1.2.2. Uncoil the cable between the charger and the lamp.
Χ DO NOT pull the charger plug from the mains socket by the lead.
WARNING! DO NOT use any other type of charger with this product, other than the supplied mains charger. Failure to observe this warning could result in injury and or fire and will invalidate the warranty.
Χ DO NOT try to take the charger plug apart.
Χ DO NOT use the charger plug to charge or power any other electrical item.
Χ DO NOT get the charger wet or use it in wet, damp conditions (for indoor use only).
1.3. BATTERY SAFETY
WARNING! To reduce the risk of burns or fire:
Χ DO NOT attempt to open, disassemble, modify or service the battery pack.
Χ DO NOT crush, puncture, short external contacts or dispose of in fire or water.
Χ DO NOT expose to temperatures above 60°C (140°).
INTRODUCTION
Robust aluminum design with built-in spring-loaded telescopic mounting brackets. Both brackets can rotate 360° individually making it easy to direct the light where required. 10 SMD LEDs have two options on light settings; full – 1000lm, and a half – 500lm. Includes battery level indicator, mains charger, and USB lead.
SPECIFICATION
Model No: ………………………………………………………..LED138
Battery: ……………………………………………….3.7V 4.4Ah Li-ion
LED Type: ……………………………………………………………. SMD
Lumen Output: ……………………………………………. 500/1000lm
Min./Max Width:. ……………………………………… 1200/1800mm
Charging Time: ………………………………………………………4.5hr
Operating Time: ………………………………….. Low / High 3 / 6hr
Power: …………………………………………………………………..10W
CHARGING
4.1.The battery fitted to this lamp is considered to be a consumable item and its ability to accept charge will reduce over time. We will warranty it against mechanical and electrical defects for a period of one year, this does not cover fair wear and tear. If the battery is not properly charged before first use, or regularly conditioned, its capacity will diminish. Under these circumstances, we will not replace the battery even if it is less than one year old.
4.2. Connect the charger cable to the charging port on the lamp, see fig.1. Plug into the power supply and turn on, the charge LEDs on the lamp will light as the battery charges. When fully charged all three green lamps will be lit.
4.3. When the battery has fully charged (approx 4.5 hrs) disconnect from the mains supply.
NOTE: The Lithium battery does not suffer from memory effect and once fully charged may be stored for up to six months without another charge.
OPERATION
5.1. Place the hook at the end of the lamp over one edge of the bonnet and gently pull the other hook towards the other side of the bonnet.
5.2. Steady the lamp with one hand, whilst extending the hook over the other side of the bonnet.
5.3. Rotate the lamp to provide the best illumination of the work being undertaken.
5.4. To use the lamp, scroll through the three settings using the on/off switch above the power socket. Press once for 100% output, once more for 50% output and a third press to turn the lamp off. The charge status LEDs will light when the on/off switch is pressed or whilst charging.
MAINTENANCE
6.1. Keep the lamp clean and check for damage before every use. If damage is observed, remove it from use until the unit is repaired.
Parts support is available for this product. Please email or telephone 01284 757500
Remove the screws in the black section of the lamp control section to remove the batteries.
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling center, and disposed of in a manner that is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications, and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park
Bury St Edmunds, Suffolk. IP32 7AR
