Honeywell TH5110D Non-Programmable Thermostat Instruction Manual

TH5110D Non-Programmable Thermostat
Instruction Manual

The TH5110D Thermostat provides electronic control of 24 Vac single-stage heating and cooling systems or 750 mV heating systems.
For assistance with your product please visit www.honeywellhome.com or call Customer Care toll-free at 1-800-468-1502.

Read and Save These Instructions

FEATURES

• Large, Clear, Backlit Display: Easy to see and read— even in the dark.
• Precise Comfort Control: ±1ºF of your set temperature.
• Simplified Operation: Soft-key controls.
  Simultaneously displays both room temperature and temperature setting.
• Easy Change Battery Holder.
• Built-in Compressor Protection: Minimum-off timer protects the compressor from restarting too early after a shutdown.

GET TO KNOW YOUR THERMOSTAT

Thermostat

Display

OPERATE YOUR THERMOSTAT

Set System Setting
Press the System button to select Heat, Off, Cool, or Auto:
Heat—The thermostat controls the heating system.
Off—Both the heating and cooling systems are off.
Cool—The thermostat controls the cooling system.
Auto—Thermostat automatically changes between heating and cooling operation, depending on indoor temperature. See the Auto Changeover section.

CAUTION
Equipment Damage Hazard.
Air conditioning compressor damage is possible.
Do not operate the cooling system when the outdoor temperature is below 50°F(10°C).

Set Fan Setting
Press the Fan button to select Auto or On:
Auto—Normal setting for most homes. The fan runs only when the heating or cooling system is on.
On—The fan runs continuously. Use this setting for improved air circulation or for more efficient air cleaning.

Change Temperature Setting
Press the Up or Down button to select the desired temperature setting.

NOTE: The first press of the Up or Down button turns on the backlight. The second press of the Up or Down button changes the temperature setting.

REPLACE BATTERIES

1. When the Replace Battery indicator is flashing, replace batteries promptly with two fresh AAA alkaline batteries.
   NOTE: The thermostat does not lose any settings when the batteries are replaced; all settings are permanently stored in memory.
2. Press the battery holder latch to release the battery holder.
3. Remove the battery holder from the thermostat.
   
4. Remove the old batteries and insert two fresh AAA alkaline batteries as marked on the battery holder.
   
5. Insert battery holder as shown.
   

REVIEW BATTERY TIPS

1. Replace the batteries as soon as Replace Battery flashes in the display. The Replace Battery indicator flashes in the display two months before the batteries run down completely.
2. Always use fresh AAA alkaline batteries.
   Non-alkaline batteries do not last as long and can leak, causing damage to the thermostat.
3. Although the thermostat has a Replace Battery indicator, replace the batteries once per year to prevent the thermostat and heating/cooling system from shutting down due to a lack of battery power.
   NOTE: Replacing the batteries once a year also helps prevent battery leakage that can damage the thermostat.
4. As a precaution, replace the batteries when leaving your home for more than a month to prevent your heating/cooling system from shutting down if the batteries run down completely.

BUILT-IN COMPRESSOR PROTECTION

The TH5110D Thermostat has built-in compressor protection (minimum-off timer) that prevents the compressor from restarting too early after a shutdown.
The minimum-off timer is activated after the compressor turns off.
If there is a call during the minimum-off timer, the thermostat flashes “Cool On” or “Heat On” on the display.
When the minimum-off timer expires, “Cool On” or “Heat On” appears solidly on the display and the compressor and the fan turn on.

AUTO CHANGEOVER

Auto Changeover is a feature used in climates where both air conditioning and heating are used on the same day. The Auto setting appears only if the thermostat is set up for  Auto Changeover by your heating and air conditioning dealer. In some installations, Auto may be the only system selection.
The following pages in this Auto Changeover section provide an example of how to change both the cool and heat temperature settings when the system is set to Auto.
When you are adjusting the temperature setting, if “▲Cool” or “ ▼Heat” appears in the display, the temperature setting of the opposite mode is also being adjusted. The thermostat automatically keeps the cool and heat temperature settings three degrees apart (called deadband). This three-degree Deadband is not adjustable.

1. Press the System button to change the System setting to Auto.
   NOTE: The Auto setting appears only if the thermostat is set up for Auto Changeover by your heating and air conditioning dealer.
2. Press the Up or Down button to raise or lower the cool temperature setting.
3. Press the Select Heat/Cool button to display the Heat temperature setting. “Select Heat/Cool” flashes for six seconds.
   
4. Press the Up or Down button to raise or lower the heat temperature setting.
5. “Select Heat/Cool” stops flashing six seconds after the last button press. The thermostat then returns to displaying “Auto” for the System setting.
   

Troubleshooting Tips

CUSTOMER ASSISTANCE

For assistance with your product, please visit www.honeywellhome.com or call Customer Care toll-free at 1-800-468-1502.
Before calling, please have the thermostat model number and date code available.

FIVE-YEAR LIMITED WARRANTY

Resideo warrants this product, excluding battery, to be free from defects in workmanship or materials, under normal use and service, for a period of five (5) years from the date of first purchase by the original purchaser. If at any time during the warranty period the product is determined to be defective due to workmanship or materials, Resideo shall repair or replace it (at Resideo’s option).
If the product is defective,
(i) return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it; or (ii) call Resideo Customer Care at 1-800-468-1502. Customer Care  will make the determination whether the product should be returned to the following address: Resideo Return Goods, 1985 Douglas Dr. N., Golden Valley, MN 55422, or  whether a replacement product can be sent to you.
This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Resideo that the defect was caused by damage that occurred while  the product was in the possession of a consumer.
Resideo’s sole responsibility shall be to repair or replace the product within the terms stated above. RESIDEO SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE  OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR  INDIRECTLY, FROM ANY BREACH OF  ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY RESIDES MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES,  INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE FIVE-YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state. If you have any questions concerning this warranty, please write  Resideo Customer Care, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-468-1502

www.resideo.com
Resideo Technologies, Inc.
1985 Douglas Drive North, Golden Valley, MN 55422
1-800-468-1502
69-1713—01 M.S. Rev. 06-21 | Printed in the United States
© 2021 Resideo Technologies, Inc. All rights reserved.
The Honeywell Home trademark is used under license from Honeywell International, Inc. This product is manufactured by Resideo Technologies, Inc. and its affiliates.