Panasonic EH-NA67 Family and Children Hair Dryer Instruction Manual
Operating Instructions (Household use)
Hair Dryer
Model No. EH-NA67
Thank you for purchasing this Panasonic product. Before operating this unit, please read these instructions completely and save them for future use.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, especially when children are present, basic safety precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING
KEEP AWAY FROM WATER
DANGER
As with most electrical appliances, electrical parts are electrically live even when the switch is off.
To reduce the risk of death by electric shock:
- Always “unplug” it immediately after using it.
- Do not use it while bathing.
- Do not place or store this appliance where it can fall or be pulled into a tub or sink.
- Do not place in or drop into water or other liquid.
- If an appliance falls into water, “unplug it” immediately. Do not reach into the water.
WARNING
To reduce the risk of burns, electrocution, fire, or injury to persons:
- An appliance should never be left unattended when plugged in.
- Close supervision is necessary when this appliance is used by, on, or near children or individuals with certain disabilities.
- Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
- Never operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been damaged or dropped into water. Return the appliance to a service center for examination and repair.
- Keep the cord away from heated surfaces. Do not wrap the cord around the appliance.
- Never block the air openings of the appliance or place it on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair, and the like.
- Never use it while sleeping.
- Never drop or insert any object into any opening.
- Do not use outdoors or operate where aerosol(spray) products are being used or where oxygen is being administered.
- Do not use an extension cord with this appliance.
- Do not direct hot air toward the eyes or other heat-sensitive areas.
- Attachments may be hot during use. Allow them to cool before handling.
- Do not place the appliance on any surface while it is operating.
- While using the appliance, keep your hair away from the air inlets.
- Do not use with a voltage converter.
- Do not use in countries with 220/240 volt electrical systems- use only with 120 volt electrical systems.
SAVE THESE INSTRUCTIONS
NanoeTM is a trademark of Panasonic Corporation. A nanoeTM is a nano-sized ion particle coated with water particles.
Safety precautions
To reduce the risk of injury, loss of life, electric shock, fire, and damage to equipment or property, always observe the following safety precautions.
Explanation of symbols
The following symbols are used to classify and describe the level of hazard, injury, and property damage caused when the denotation is disregarded and improper use is performed.
Denotes a potential hazard that will result in serious injury or death.
Denotes a potential hazard that could result in serious injury or death.
Denotes a hazard that could result in minor injury or property damage.
The following symbols are used to classify and describe the type of instructions to be observed.
Some parts of the safety precaution illustrations differ from the actual product.
– Doing so may cause burns, electric shock, or injury.
– Doing so may cause ignition or injury due to abnormal operation. Contact an authorized service center for repair.
Do not deface, modify, forcefully bend or pull the cord or plug. Also, do not place anything heavy on, twist or pinch the cord.
– Doing so may cause electric shock, burn or fire due to a short circuit.
– Doing so may cause fire or electric shock.
– Doing so may cause the wire in the cord to break with the load, and may cause electric shock or fire due to a short circuit.
– Doing so may cause the wire in the cord to break with the load, leading to electric shock or fire due to a short circuit.
– Doing so may cause burn, electric shock, or fire due to a short circuit.
– Doing so may cause burn, electric shock, or fire due to a short circuit.
– Doing so may cause electric shock or injury.
– Doing so may cause electric shock or fire due to a short circuit.
– Doing so may cause fire.
– Doing so may cause electric shock or fire.
– Doing so may cause fire, electric shock, or burn.
– Doing so may cause an explosion or fire.
– Doing so may cause electric shock or fire.
– Failure to do so may cause fire, electric shock, or injury.
- Air is not emitted
- Unit stops sporadically
- The interior becomes red hot and smoke is emitted
– Immediately request inspection or repair at an authorized service center.
– Failure to do so may cause fire or electric shock.
– Failure to do so may cause fire or electric shock.
– Failure to do so may cause fire, electric shock, or burn.
– Failure to do so may cause burn or fire.
– Failure to do so may cause fire or burn.
– Failure to do so may cause the wire in the cord to break and may cause burn, electric shock, or fire due to a short circuit.
– Failure to do so may cause fire due to insulation failure caused by humidity.
– Failure to do so may cause an accident or injury.
– Failure to do so may cause an accident or injury.
– Failure to do so may cause an accident or injury.
– Failure to do so may cause an accident or injury.
– Doing so may cause electric shock or ignition.
– Your hair may get dangled in the air inlet, which could damage the hair.
– Doing so may cause a burn.
– Doing so may cause a burn.
– Your hair may get dangled in the air inlet, which could damage the hair.
– Doing so may cause fire or electric shock.
– Failure to do so may cause burns to the hair.
– Your hair may get tangled in the air inlet, which could damage the hair.
– Failure to do so may cause fire or burn.
OPERATING INSTRUCTIONS
This product is intended for household use only.
This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized outlet only one way. If the plug cannot be inserted fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
This appliance is also provided with an ALCI protective device that may make the appliance inoperable under some abnormal conditions (such as immersion of the appliance). If the appliance becomes inoperable, return the appliance to a service center for examination and repair. Each time the appliance is used, check the safety plug to verify it is in proper working order. Plug the appliance in an electrical outlet and press the test button. The hair dryer should stop immediately. To resume operation, press the reset button.
Parts identification
An Air outlet
B Concentrator nozzle
C nanoe™ outlet
D nanoe™ lamp
E Cool-shot button
F Handle
G Ring for hanging
H Cord
I Power plug
J Temperature selector
HOT: Hot air
WARM: Warm air
COOL: Cool air
K Power switch
HIGH: Strong airfl ow
LOW: Gentle airfl ow
OFF: Off
L Air inlet grille
M Filter
Make sure to attach the filter to the air inlet when using the hair dryer.
N Panel
O Oscillating quick-dry nozzle
P Diffuser
The concentrator nozzle
Focuses and concentrates airflow for precise hair styling.
Oscillating quick-dry nozzle
Delivers strong and soft airflows for fast drying. Automatically moves to prevent hot spots for more gentle drying.
Attach the oscillating quick-dry nozzle so this air outlet is vertical.
For creating full-bodied hair with lots of volume and styling
How to use the hairdryer
Always check that the filter is securely attached before using.
- Select the temperature of the airflow with the temperature selector (J).
- Select the intensity of the airflow with the power switch (K).
Notes
- The air remains cool while the cool-shot button is held down.
- nanoeTM is produced when the power switch (K) is set to position “LOW” to “HIGH”.
- nanoeTM is invisible to the naked eye.
- If you are worried about hair damage, set the switch to “LOW: Gentle airflow” before use
- Drops of water may blow out of the nanoeTM outlet (C) during use, but this is not a malfunction.
- A humming noise may come out of the nanoeTM outlet (C), but this is the sound of nano em being discharged and is not a malfunction.
- The effects of nanoeTM might not be felt by the following people. People with crimpy hair, strong curly hair, very smooth hair, short hair, or who have had a hair straightening perm in the last three or four months.
- You may notice a characteristic odor when using this hairdryer. This is not harmful to the human body.
The best-recommended usage of the oscillating quick-dry nozzle
When using the oscillating quick-dry nozzle in automatic swing mode, make sure to set the wind speed to “HIGH”.
- Please confi rm that the power switch is set to the position “OFF” before using the oscillating quick-dry nozzle.
- Hold both sides of the oscillating quick-dry nozzle with your hands, and pull it out gently with force until you hear a “click” sound, indicating the automatic swing mode of the oscillating quick-dry nozzle has been turned on.
- Choose the temperature of wind as required.
- Set the power switch to “HIGH”.
· If you want to dry your hair quickly, it is recommended to choose the mode “HIGH” + “HOT” or “WARM”. - Dry your hair, then turn off the automatic swing mode for theoscillating quick-dry nozzle before tidying your hair.
Make sure that the power switch is set to the position “OFF”.
Hold both sides of the oscillating quick-dry nozzle with your hands, and slightly press it inward with force until you hear a “click” sound, indicating the automatic swing mode of the oscillating quick-dry nozzle has been locked. - Set the wind speed to “LOW”, then set the temperature of the wind to “COOL “. Finally, set your hair according to your own particular preferences.
Note Oscillating quick-dry nozzle may not function properly at low power mode (“LOW”).
About nanoeTM
What is nanoeTM?
(nanoeTM, generation method: high voltage discharge) nanoeTM is generated by collecting the available moisture in the air, so depending on the usage environment, nanoeTM may not be generated. In environments of low temperature and low humidity, moisture in the air becomes difficult to collect. When this occurs, negative ions are generated. nanoeTM is an ion wrapped in water that are invisible to the human eye.
How nanoeTM works
Generally, hair has properties that make it easy to become positively charged with electricity. These properties attract strongly negatively charged nanoeTM which penetrates the hair with moisture. Furthermore, they make the hair slightly acidic, tighten cuticles and keep your hair strong, elastic, and healthy.
Panel effect
When nanoeTM continues to strike hair, hair becomes negatively charged. As a result, the nanoeTM and negatively charged hair repel each other, making it difficult for nanoeTM to reach hair. With the nanoeTM Charge System, by just gripping the panel together with the handle, the negative charge accumulated on hair is released. Because of this, nanoeTM continues to penetrate into hair, supplying moisture and thoroughly moistening down to the tips of the hair.
Maintenance of the hairdryer
Always turn the power switch off and disconnect the plug from the household outlet. (Except when performing maintenance on the air outlet)
Maintaining the main body
Do this when dirty
To clean the hairdryer (when it is dirty), soak a cloth in the soapy water and squeeze it out firmly, then wipe with the cloth.
Notes
- Do not use substances such as alcohol, nail polish remover or detergent (hand soap). Doing so may result in malfunction or part cracks or discoloration.
- Do not leave the appliance with hairdressing products or cosmetics on it. Doing so will cause deterioration of the plastic, leading to discoloration and cracks.
Maintaining the nanoeTM outlet
- Use commercially available cotton swabs. (We recommend the thin cotton swabs made for use with babies.)
- This maintenance allows the hairdryer to sustain the generated level of nanoeTM over a long period.
- Dampen the end of the cotton swab with tap water.
- A needle portion is located deep within the nanoeTM outlet. Using the swab, rub
Maintaining the air inlet
Clean the air inlet once a month or over.
- When dust etc. has built up, detach the filter from the hairdryer and remove the dust etc. using a toothbrush or vacuum cleaner.
- Use a commercially available toothbrush.
- Pull on the catch on the bottom side of the filter to the bottom side of the filter to detach.
- Remove any dust etc. adhered to the filter or air inlet grille.
· Remove the dust etc. adhered to the outside of the filter using a vacuum cleaner. If this does not remove the dust, use the thick part of your fingers to push the dust, etc. through the fine mesh on the internal side towards the metal mesh on the external side, and scrub away carefully with a toothbrush.
· Using the toothbrush, carefully scrub away any dust, etc. from the internal side of the filter.
· Using a vacuum cleaner or toothbrush, carefully remove any dust, etc. adhered to the air inlet.
· Rubbing forcefully with your nails may tear the filter, so please use a toothbrush. - Attach the filter securely, starting with the upper side.
· Keep pressing until you hear a “click” from both upper and lower catches.
Maintaining the air outlet
- The hair dryer should be plugged into the household outlet only in case of maintenance for the air outlet.
- Use a commercially available toothbrush.
- Switch the temperature selector to “COOL” and blow away the dust etc. as you scrub with the toothbrush.
- During maintenance, do not block the air inlet with your hands, etc.
- Be careful when using the hairdryer for the first time after maintenance, since it may blow out dust etc.
Scrub to remove any dust, hair, etc. blocking the mesh.
Troubleshooting
Problem | Possible cause | Action |
It switches frequently to cold air while using in “HOT” mode, or sparks can be seen within the body. (These sparks are caused by the thermostat switch, the protective device and this is not dangerous.) |
Lint has accumulated on the air inlet or air outlet. Hair or something is blocking the air inlet. |
Remove accumulated lint. |
The hot air is abnormally hot. | Do not block the air inlet. | |
The power plug is abnormally hot. | The connection to the household outlet is loose. | Use a household outlet that fi ts securely. |
Sparks are generated inside the nanoe™ outlet. | Abnormality is caused by a dirty electrode (needle portion). | Perform maintenance of the nanoe™ outlet. |
The nanoe™ outlet emits a noise (crackling noise). | Perform maintenance of the nanoe™ outlet. |
If the problems still cannot be solved, contact the store where you purchased the unit or a service center authorized by Panasonic for repair.
Specifications
Product name | Hair Dryer |
Product model | EH-NA67 |
Power source | 125 V 60 Hz |
Power consumption | 1 875 W |
Accessories | Concentrator nozzle, Oscillating quick-dry nozzle, Diffuser |
…can save a life!
If YOU MUST USE YOUR HAIRDRYER IN THE BATHROOM, INSTALL A GFCI* NOW!
Your local electrician can help you decide which type is best for you- a portable unit that plugs into the electrical outlet or a permanent unit installed by your electrician. The National Electrical Code now requires GFCIs in the bathrooms, garages, and outdoor outlets of all new homes.
WHY DO YOU NEED A GFCI?
A GFCI can save your life! Compared to that, the price is small!! Don’t wait …install one now!
*GFCI is a sensitive device that reacts immediately to a small electric current leak by stopping the electricity flow.
USER MAINTENANCE INSTRUCTIONS
This hair dryer is virtually maintenance-free. No lubrication is needed. For proper operating performance, the hairdryer must be kept clean. When cleaning is needed, unplug the cord, and clean dust and lint from air intake openings with a small brush or the brush attachment of a vacuum cleaner. The outer surface of the hairdryer should be wiped clean with a damp cloth only. This hair dryer should be stored out of reach of children.
Warning To prevent the risk of electric shock, personal injury, or fire, observe the following:
- Do not perform any servicing. This hair dryer has no user-serviceable parts.
- Never allow the power supply cord to be pulled, twisted, or severely bent.
- Never wrap the cord tightly around the hairdryer. Damage will occur at the high flex point of entry into the hairdryer, causing it to rupture and short. Inspect the cord frequently for damage. Stop use immediately if the damage is visible or the unit stops or operates intermittently.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
FCC Caution:
To assure continued compliance, install and use in accordance with provided instructions. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Personal Care & Beauty Care Products
FOR USA ONLY
30-Day Quality
Satisfaction Guarantee
If you are dissatisfied with any Panasonic Personal Care & Beauty Care Products for any reason, simply return it to the place of purchase with a dated proof of purchase, in the original packaging, with all accessories, parts, and instructions, within 30 days of the date of purchase, for a full refund, or call Panasonic at 1-800-338-0552. Abuse or misapplication of this product voids the guarantee.
PRODUCT REGISTRATION (U.S. customers only)
Go to www.panasonic.com/register and register your product now to receive these benefits:
Safety Notification
We contact our customers in case of a recall
Owner Verification
Proof of purchase in case of product theft or loss
Efficient Warranty Service
In case there is a problem with your product
Special Offers and Promotions from Panasonic
FOR YOUR CONVENIENCE, WE HAVE ESTABLISHED A TOLL-FREE (IN USA ONLY) NATIONAL ACCESSORY PURCHASE HOTLINE AT 1-800-332-5368. IN CANADA, CONTACT PANASONIC CANADA INC. AT THE ADDRESS OR TELEPHONE NUMBER ON THE BACK PAGE.
ESTADOS UNIDOS, COMUNÍQUESE CON:
Panasonic Corporation of North America
Two Riverfront Plaza, Newark, NJ 07102-5490
AU CANADA, COMMUNIQUEZ AVEC :
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3
www.panasonic.com
Servicio • Asistencia • Accesorios Dépannage • Assistance • Accessoires
Call 1-800-338-0552 (In USA)
http://shop.panasonic.com/personal-care
http://shop.panasonic.com/support
www.panasonic.ca/english/support (En Canadá)
www.panasonic.ca/french/support (Au Canada)
http://www.panasonic.com
Panasonic Corporation
http://www.panasonic.com
© Panasonic Corporation 2020-2021
Printed in Thailand
Imprimé en Thaïlande
Impreso en Tailandia
EH9210NA672352 E1120-10321