Bosch GTA 6000 Professional Table Saw Stand Instruction Manual

BOSCH GTA 6000 Professional Table Saw Stand

OVERVIEW

WHATS IN THE BOX

Safety Instructions

General Safety Instructions
Read all the warnings and instructions included with the saw stand or the power tool you intend to mount on it. Failure to observe the safety and general instructions may result in electric shock, fire and/or serious injury.

Safety Instructions for Saw Stands

  • Disconnect the plug from the power source and/or remove the battery from the power tool before making any adjustments to the power tool or changing accessories. Accidents can occur when power tools are started unintentionally.
  • Assemble the saw stand properly before mounting the power tool. Correct assembly is important to prevent the risk of collapsing.
  • Firmly secure the power tool to the saw stand before using it. You may lose control of the power tool if it slips on the saw stand.
  • Place the saw stand on a firm, flat, horizontal surface. If there is a chance that the saw stand will slip or wobble, the safe and steady machining of the workpiece cannot be guaranteed.
  • Do not overload the saw stand or climb or stand on it. Overloading or standing on the saw stand can raise its centre of gravity, causing it to tip over.
  • Ensure that all screws and connecting pieces are tightly fastened when carrying out work. Loose connections can cause instability and inaccurate sawing.
  • Ensure that long and heavy workpieces do not unbalance the saw stand. The free end of long and heavy workpieces must have something placed underneath it or be supported.
  • When pushing together or pulling apart the saw stand, do not put your fingers near the points of articulation. There is a risk of fingers being crushed.

Symbols

The following symbols may provide you with important information about the use of your saw stand. Please take note of these symbols and their meaning. Knowing what these symbols mean will help you to use your saw stand more effectively and more safely.

Symbols and their meaning
The maximum load bearing capacity (power tool + workpiece) of the saw stand is 100 kg.

Product description and specifications

Intended Use
The saw stand is intended for holding the following Bosch benchtop saws (stand 2021.08): GTS 10 XC (3 601 L30 4..) The saw stand and power tool are intended for cutting boards and profiles

Product Features
The numbering of the components shown refers to the illustrations on the graphics pages at the beginning of the manual.

  1. Release lever
  2. Base frame
  3. Saw stand leg
  4. Fastening set
  5. Power tool fastening set

Technical Data

  • Saw stand GTA 6000
  • Article number 3 601 M24 10.
  • Base frame dimensions mm 670 x 750
  • Saw stand height mm 602
  • Max. load bearing capacity (power tool + workpiece) kg 100
  • Weight according to EPTA-Procedure 01:2014 kg 12.5

Assembly

Items included
Check to ensure that all the parts listed below have been supplied before assembling the saw stand:

  • Base frame (2)
  • Saw stand legs (3) (4 pieces)
  • Fastening set (4) consisting of: Cross-head screws M8 x 45 (4 pieces), lock nuts M8 (4 pieces)
  • Fastening set (5) consisting of: Hex screws M8 x 75 (4 pieces) washers M8/18 mm (8 pieces), nuts M8 (4 pieces

Extra tools required (not included in the delivery):

  • Cross-headed screwdriver
  • Open-end spanner (13 mm)

Assembling the saw stand
Carefully remove all parts included in the delivery from their packaging. Remove all packing material.

  • Place the folded base frame (2) flat on the floor.
  • Pull up the base frame (2) by the unlocking lever (1). Let go of the unlocking lever whilst pulling it up so the saw stand can click into place.
  • Insert the saw stand legs (3) into the square pipes in the base frame (2) until they are aligned with the assembly holes.
  • Screw together the saw stand legs and the base frame using the nuts and bolts in the fastening set (4).

Securing the power tool

  • Centre the power tool on the base frame (2).
  • Secure the power tool to the base frame with the fastening set

Operation

Working Advice
Always hold the workpiece firmly in place, especially long, heavy pieces. Once the workpiece has been cut, the centre of gravity may be displaced, causing the saw stand to tip over. Do not overload the saw stand. Always observe the maximum load-bearing capacity of the saw stand.

Transport
The power tool must not be mounted on the saw stand when the saw stand is being folded up or unfolded.

  • Remove the power tool.
  • Pull the unlocking lever (1) upwards and fold up the saw stand.

Maintenance and Service

After-Sales Service and Application Service Our after-sales service responds to your questions concerning the maintenance and repair of your product as well as spare parts. You can find explosion drawings and information on spare parts at: www.bosch-pt.com The Bosch product use advice team will be happy to help you with any questions about our products and their accessories. In all correspondence and spare parts orders, please always include the 10‑digit article number given on the nameplate of the product. Great Britain Robert Bosch Ltd. (B.S.C.) P.O. Box 98 Broadwater Park North Orbital Road Denham Uxbridge UB 9 5HJ At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a product in need of servicing or repair. Tel. Service: (0344) 7360109 E-Mail: You can find further service addresses at: www.bosch-pt.com/serviceaddresses

Disposal
Saw stands, accessories and packaging should be recycled in an environmentally responsible manner.