Bosch NIT5060UC 30-Inch Frameless Induction Cooktop Instruction Manual

NIT5060UC 30-Inch Frameless Induction Cooktop
Instruction Manual
NIT5460UC /NIT5660UC /NIT8060SUC/ NIT8060UC
NITP060SUC /NITP060UC/ NIT8660SUC /NIT8660UC/ NITP660SUC/
NITP660UC

Register your appliance and join the Bosch family of perks: bosch-home.com/us/mybosch

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS
Read all instructions carefully before use. These precautions will reduce the risk of electrical shock, fire, and injury to persons. When using kitchen appliances, basic safety precautions must be followed including those in the following pages.

Safety definitions

Here you can find explanations of the safety signal words used in this manual.
WARNING
This indicates that death or serious injuries may occur as a result of the non-observance of this warning.
CAUTION
This indicates that minor or moderate injuries may occur as a result of the non-observance of this warning.
NOTICE:
This indicates that damage to the appliance or property may occur as a result of non-compliance with this advisory.
Note: This alerts you to important information and/or tips.

General information

Read this manual carefully.
Keep the instructions, the appliance pass, and the product information safe for future reference or for the next owner.
Do not connect the appliance if it has been damaged in transit.

General safety instructions

IMPORTANT: THE APPLIANCE MUST BE INSTALLED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR’S USE.
INSTALLER: LEAVE THESE INSTALLATION INSTRUCTIONS WITH THE UNIT FOR THE OWNER.
OWNER: PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Examine the appliance after unpacking it. In the event of transport damage, do not plug it in.
WARNING
If the information in this manual is not followed exactly, fire or shock may result causing property damage or personal injury.
Do not repair, replace or remove any part of the appliance unless specifically recommended in the manuals. Improper installation, service, or maintenance can cause injury or property damage.
▶ Refer to this manual for guidance.
▶ All other servicing should be done by an authorized service provider.
When installing a cooktop over a single oven, be sure to follow the instructions in both the oven’s and the cooktop’s installation manuals.
▶ You can find a list of approved combinations of cooktop and oven in the Approved Combination Matrix of your cooktop, or you can contact Customer Service for the latest list of approved combinations. Do not try to install your cooktop over any oven that is not stated in that list. DO NOT install any refrigerators, dishwashers, ovens (without ventilation), or washing machines below the cooktop. Refer to the Approved Combination Matrix. Never modify or alter the construction of the appliance. The appliance should only be used if installed by a qualified technician in accordance with these installation instructions. The manufacturer is not responsible for any damage resulting from incorrect installation. To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided.
▶ If cabinet storage is to be provided, the risk can be reduced by installing a hood that projects horizontally a minimum of 5″ (127 mm) beyond the bottom of the cabinet.
▶ Verify that cabinets above the cooktop are a maximum of 13″ (330 mm) deep.
NOTICE:
We strongly recommend the installation of a ventilation system with this appliance.
WARNING
Remove all tape and packaging before using the appliance.
▶ Destroy the packaging after unpacking the appliance.
▶ Dispose of packaging in an environmentally responsible manner.
▶ Never allow children to play with packaging material.

Appliance handling safety

WARNING
Hidden surfaces may have sharp edges.
▶ Use caution when reaching behind or under appliances.

Safety codes and standards

This appliance complies with the latest version of one or more of the following standards:

UL 858 – Household Electric Ranges
CAN/CSA-E60335-2-6, The Standard for the Safety of Household and similar electrical appliances.

It is the responsibility of the owner and the installer to determine if additional requirements and/or standards apply to specific installations.

Electrical safety

Installer – show the owner the location of the circuit breaker or fuse. Mark it for easy reference.
If required by the National Electrical Code (or Canadian Electrical Code), this appliance must be installed on a separate branch circuit.
Local codes vary. The installer is responsible for ensuring that the installation, connections, and grounding comply with all applicable codes. The manufacturer is not responsible for any issues associated with the improper installation of this product.
The circuit breaker should have a contact separation of at least 3 mm on all poles.
Refer to the rating plate for more information.
→ “Rating plate location”, Page 10
This appliance also incorporates an internal earth connection for functional purposes only.

WARNING
Before installing, turn the power OFF at the service panel.
▶ lock service panel to prevent power from being turned ON accidentally.
IMPROPER GROUNDING CAN RESULT IN A RISK OF ELECTRIC SHOCK
▶ Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.
▶ DO NOT USE AN EXTENSION CORD.
GROUNDING INSTRUCTIONS
▶ This appliance must be grounded.
▶ Grounding reduces the risk of electric shock by providing a safe pathway for electric current in the event of a short circuit.
▶ Be sure your appliance is properly installed and grounded by a qualified technician.
▶ Installation, electrical connections, and grounding must comply with all applicable codes.
Before you turn on the power supply, make sure all controls are in the OFF position.

State of California Proposition 65 Warnings

This product may contain a chemical known to the State of California, which can cause cancer or reproductive harm. Therefore, the packaging of your product may bear the following label as required by California:
STATE OF CALIFORNIA PROPOSITION 65 WARNING:
WARNING-
Cancer and Reproductive Harm- www.P65Warnings.ca.gov

Before you begin

Read these instructions before you begin to install your appliance.

Parts included

After unpacking all the parts, check for any damage in transit and for completeness of delivery.

Tools and parts needed

Prepare these tools and accessories before you start to install your appliance.

Pencil
Measuring tape
Crosshead screwdriver
Drill with bit 1/4″ (6 mm)
Jigsaw

Note: Additional materials may be necessary for installation in solid surface countertops. Contact the countertop manufacturer.

Cabinet requirements

Ensure that the cabinetry at the installation location meets the requirements for a safe installation.

The distance from the top of the cooktop to the bottom of the cabinets above must be a minimum of A=30″ (762 mm).
This distance can be reduced to A=24″ (610 mm) when the bottom of the wood or metal cabinet is protected by not less than ¼” (6.35 mm) flame-retardant billboard covered with not less than no. 28 gauge sheet metal, 0.015″ (0.4 mm) stainless steel, 0.024″ (0.6 mm) aluminum or 0.020″ (0.5 mm) copper.
Verify that unprotected cabinets above the cooktop are a maximum of B=13″ (330 mm) deep.

Installation in combination with other products
Both products must be installed according to their specific product installation instructions.
Installing a cooktop over ovens and microwaves:
Only certain models may be installed over an oven or a microwave. Verify the Approved Combination Guide supplied with these instructions for approved installation combinations. Both products will have a label stating Approved Combination Guide.
Installing a range hood or a microwave hood above the cooktop:
Follow the range hood or microwave hood installation instructions for dimensional clearance above the cooktop surface.

Countertop requirements

Ensure that the countertop into which the cooktop is to be installed meets these requirements for a safe installation.
WARNING
To reduce the risk of ignition of surrounding combustible materials, install at least 2″ (51 mm) from both sidewalls and the rear wall.

The countertop must be level and horizontal.
The stability of the countertop must be maintained after the cut-out has been made.
Solid surface countertops often require special installations. For example, heat-reflective tape and rounded corners may be necessary.
Contact the countertop manufacturer for instructions specific to your countertop.

Prepare installation space

Prepare installation space Create the cutout in the countertop according to the instructions.
General countertop requirements:

The angle of the cut surface to the countertop must be 90°.
With multi-layered countertops, secure strips laterally in the cutout if necessary.
After creating the cutout, remove all shavings.
Seal the cut surfaces in a heat- and water-resistant manner.
Observe the minimum distance between the device underside and cabinet surfaces of ⅜” (10 mm).
The countertop into which the cooktop is installed must be heat-resistant up to 140° F (90 °C).
The countertop into which the cooktop is installed must be at least ¹³/₁₆” (20 mm) thick.
If the thickness of the countertop into which the cooktop is installed does not comply with the specifications, reinforce the worktop using fire- and water-resistant material until it reaches the minimum thickness. Otherwise, sufficient stability cannot be assured.
The countertop into which the cooktop is installed should withstand loads of approx. 133 lbs (60 kg).
Confirm the cooktop is level only after it has been installed.

Cutout dimensions for 24″ cooktops

Refer to these measurements for the models stated here.

NIT5460UC

Cutout dimensions for 30″ cooktops

Refer to these measurements for the models stated here.

NIT5060UC
NIT8060SUC
NIT8060UC
NITP060SUC
NITP060UC

Cutout dimensions for 36″ cooktops

Refer to these measurements for the models stated here.

NIT5660UC
NIT8660SUC
NIT8660UC
NITP660SUC
NITP660UC

Cabinet ventilation requirements

To assure that the appliance works correctly, the cooktop MUST be sufficiently ventilated.
The ventilation in the lower section of the appliance requires a sufficient supply of fresh air. Ensure that the cabinet is designed in a way that supports sufficient ventilation. The following requirements must be fulfilled:
Notes

Minimum clearance between the rear of the cabinet and the kitchen wall, and between the surface of the countertop and the upper area of the drawer.
An opening at the top to the rear of the cabinet.
If the minimum clearance of 13/16″ (20 mm) is not provided at the rear of the cabinet, you must create an opening on the underside.
If the inside of the cabinet is no wider than 29 ½” (750 mm), make cutouts in the side panels.
If the appliance is installed in an island unit or another installation that is not described here, you must ensure that the cooktop is sufficiently ventilated.

Installation procedure

Follow these instructions to install the cooktop on the countertop.
CAUTION
Sharp edges.
▶ Use protective gloves when installing the appliance.
CAUTION
The appliance is heavy.
▶ It is recommended that two people install this appliance.

Installing the heat shield

For safety reasons, the heat shield must be properly installed when closed cabinets are used. This prevents components from overheating as a result of the recirculation of hot air from the cooktop. The heat shield is the same width as the cooktop.
CAUTION
Sharp edges.
▶ Use protective gloves when installing the heat shield.
Requirement: You have unpacked the cooktop.
▶ For shipping, the heat shield is screwed to the bottom of the cooktop. Unscrew the fastening screw on the heat shield. ▶ The heat shield will be able to rotate freely.

Securing the cooktop to the countertop

The cooktop must be secured from below using the hold-down brackets provided, so it does not slip.

Place the cooktop face down on a soft underground.
Attach the hold-down brackets to the underside of the cooktop with the provided short screws. 1 Do not tighten the screws.
Rotate the hold-down brackets so that the appliance can be placed in the cutout.
CAUTION Do not let the cooktop drop into place.
▶ Make sure that the cooktop is supported along the edges when carefully placing it into the cutout. Turn the cooktop over and place it carefully into the countertop cutout.
Insert the clamping screws into the hold-down bracket and secure the cooktop to the countertop. Protect delicate countertops by placing a wooden disk underneath.
Tighten the hold-down bracket screws on the cooktop underside.

Electrical connection

Read these instructions to safely connect your appliance to the electrical supply.

Electrical requirements

Ensure that the following general requirements are met.

You can find the rating plate with the electrical specifications on the underside of the appliance.
→ “Rating plate location”, Page 10

The junction box must be located within 3 feet of the cooktop connection. It should be easily accessible for service purposes.

a	max. 2¾” (69 mm) + fitting/conduit 1″ (25 mm)
b	min. 1″ (25 mm) air clearance
c	approx. 12″ (300 mm)
d	junction box
e	flexible conduit approx. 3 ft. (900 mm)

Power supply
All models must be connected with the included 39″ (1 m) flexible conduit.

Models	240 V AC, 3-wire, 60 Hz system: circuit breaker	208 V AC, 3-wire, 60 Hz system: circuit breaker
NIT5060UC	30 A	30 A
NIT8060SUC	30 A	30 A
NIT8060UC	30 A	30 A
NITP060SUC	30 A	30 A
NITP060UC	30 A	30 A
NIT5660UC	40 A	40 A
NIT8660SUC	40 A	40 A
NIT8660UC	40 A	40 A
NITP660SUC	50 A	50 A
NITP660UC	50 A	50 A
NIT5460UC	30 A	30 A

Connecting electrical supply

WARNING
Before installing, turn the power OFF at the service panel.
▶ lock service panel to prevent power from being turned ON accidentally.
Note: If the cooktop is installed and connected as specified here, it will be grounded in compliance with the National Electrical Code.

Install a suitable junction box (not furnished). The branch-circuit breakers’ ampacity, the wire sizes, and the connections must conform to the requirements of the National Electrical Code or Canadian Electrical Code and all local codes and ordinances.
Attach the flexible conduit to the junction box.
Connect the lead wires to the junction box supply wires in the proper phase.

Red wires
UL listed wire connectors
Green (or bare) ground wire (from appliance)
Cable from the home power supply
Black wires
Junction box
Flexible conduit from appliance

– Black wires of the cooktop to black house wire
– Red wires of the cooktop to red house wire
– Green or bare to ground

Checking the installation

Check if your unit is working properly after you have completed the installation steps.
WARNING
Before you turn on the power supply, make sure all controls are in the OFF position.

Remove everything from the cooktop surface including stickers.
Clean the cooktop surface with cooktop cleaning cream.
Switch on the circuit breaker.
Verify that all cooking zones function properly.

Removing the appliance

Disconnect the appliance from the power supply.
NOTICE: Do not lever the appliance out from above at the frame.
Push out the appliance from below.

Customer Service

If you have any questions on use, are unable to eliminate an issue in the appliance yourself, or the appliance needs to be repaired, please contact our Customer Service.
With any warranty repair, we will make sure your appliance is repaired by an authorized service provider using genuine replacement parts. We use only genuine replacement parts for all repairs.
Detailed information on the warranty period and terms of the warranty can be found in the Statement of Limited Product Warranty, from your retailer, or on our website.
If you contact Customer Service, you will need the model number (E-Nr.) and the production number (FD) of your appliance.
USA:
1-800-944-2904
www.bosch-home.com/us/owner-support/get-support
www.bosch-home.com/us/shop
CA:
1-800-944-2904
www.bosch-home.ca/en/service/get-support
www.bosch-home.ca/en/service/cleaners-and-accessories
For assistance with connecting to Home Connect™, you can also view instructions here:
www.home-connect.com/us/en/help-support/set-up

Model number (E-Nr.) and production number (FD)

You can find the model number (E-Nr.) and the production number (FD) on the appliance’s rating plate.
The model number (E-Nr.) can also be found on the glass-ceramic. You can also display the customer service index (KI) and the production number (FD) in the Basic settings.
Making a note of your appliance’s details and the Customer Service telephone number will enable you to find them again quickly.

Rating plate location

You can find the rating plate of your appliance:

on the underside of the appliance
in the appliance pass
You can also check the Customer Service Index (CSI) and the FD number in the basic settings.

a. Rating plate

Thank you for buying a Bosch Home Appliance!
Register your new device on MyBosch now and profit directly from:

Expert tips & tricks for your appliance
Warranty extension options
Discounts for accessories & spare parts
Digital manual and all appliance data at hand
Easy access to Bosch Home Appliances Service

Free and easy registration – also on mobile phones: www.bosch-home.com/welcome

Looking for help? You’ll find it here.
Expert advice for your Bosch home appliances, help with problems, or a repair from Bosch experts.
Find out everything about the many ways Bosch can support you: www.bosch-home.com/service
Contact data of all countries are listed in the attached service directory.

BSH Home Appliances Corporation
1901 Main Street, Suite 600
Irvine, CA 92614
USA
www.bosch-home.com
1-800-944-2904
© 2021 BSH Home Appliances Corporation

Download

Bosch NIT5060UC 30-Inch Frameless Induction Cooktop Instruction Manual

Was this manual helpful?