Whirlpool WOS52ES4MW 24-Inch Single Electric Wall Oven User Guide

Whirlpool WOS52ES4MW 24-Inch Single Electric Wall Oven

IMPORTANT SAFETY INSTRUCTIONS

WARNING

To reduce the risk of fire, electrical shock, injury to persons, or damage when using the oven, follow basic precautions, including the following

  •  Proper Installation – Be sure the oven is properly installed and grounded by a qualified technician.
  • Never Use the Oven for Warming or Heating the Room.
  • Do Not Leave Children Alone – Children should not be left alone or unattended in area where oven is in use. They should never be allowed to sit or stand on any part of the oven.
  •  Wear Proper Apparel – Loose-fitting or hanging garments should never be worn while using the oven.
  • User Servicing – Do not repair or replace any part of the oven unless specifically recommended in the manual. All other servicing should be referred to a qualified technician. Storage in Oven – Flammable materials should not be stored in an oven.
  • Do Not Use Water on Grease Fires – Smother fire or flame or use dry chemical or foam-type extinguisher.
  • Use Only Dry Potholders – Moist or damp potholders on hot surfaces may result in burns from steam. Do not let potholder touch hot heating elements. Do not use a towel or other bulky cloth.
  •  Use Care When Opening Door – Let hot air or steam escape before removing or replacing food.
  •  Do Not Heat Unopened Food Containers – Build-up of pressure may cause container to burst and result in injury.
  • Keep Oven Vent Ducts Unobstructed.
  • Placement of Oven Racks – Always place oven racks in desired location while oven is cool. If rack must be moved while oven is hot, do not let potholder contact hot heating element in oven.

DO NOT TOUCH NTS OR INTERIOR SURFACES OF OVENHEATING ELEME

Heating elements may be hot even though they are dark in color. Interior surfaces of an oven become hot enough to cause burns. During and after use, do not touch, or let clothing or other flammable materials contact heating elements or interior surfaces of oven until they have had sufficient time to cool. Other surfaces of the oven may become hot enough to cause burns – among these surfaces are oven vent openings and surfaces near these openings, oven doors, and windows of oven doors.

For self-cleaning ovens

  • Do Not Clean Gasket – The gasket is essential for a good seal. Care should be taken not to rub, damage, or move the gasket
  • Do Not Use Oven Cleaners – No commercial oven cleaner or oven liner protective coating of any kind should be used in or around any part of the oven.
  • Clean Only Parts Listed in Manual.
  • Before Self-Cleaning the Oven – Remove broiler pan and other utensils.
Product Description

These instructions cover several different models. The range you have purchased may have some or all of the items listed. The locations and appearances of the features shown here may not match those of your model. Refer to this manual or the Frequently Asked Questions (FAQs) section of our website at www.whirlpool.com for more detailed instructions. In Canada, refer to the Customer Service Section at www.whirlpool.ca

  1. Control panel
  2.  Fan and Circular heating element (not visible)
  3.  Shelf guides (the level is indicated on the front of the oven)
  4.  Door
  5. Upper heating element/grill
  6. Lamp
  7. Identification plate (do not remove)
  8. Lower heating element not visible

Oven Vents

 

  • A. Control panel
  • B. Oven
  • C. Oven vent

The oven vent(s) should not be blocked or covered since they allow the inlet of fresh air into the cooling system. Also, the bottom vent should not be blocked or covered since it allows the inlet of fresh air into the cooling system and the outlet of hot air from the cooling system. Blocking or covering vents will cause poor air circulation, affecting cooking, cleaning, and cooling results.

Positioning Racks and Bakeware

IMPORTANT

To avoid permanent damage to the porcelain finish, do not place food or bakeware directly on the oven door or bottom.
Racks

  • Position racks before turning on the oven.
  • Do not position racks with bakeware on them.
  • Make sure racks are level.
  • Place food so it will not rise into the broil element. Allow at least 1/2″ (1.3 cm) between pans and the broil element.

To move a rack, pull it out to the stop position, raise the front edge, and then lift it out. Use the following illustration and charts as a guide for positioning racks.

Inserting the Wire Shelf and other Accessories
Insert the wire shelf horizontally by sliding it across the shelf guides in correspondence to the rack positions pictured below, making sure that the side with the raised edge is facing upwards. Other accessories, such as the drip tray and the baking tray, are inserted horizontally in the same way as the wire shelf.

Rack Position

Touch Panel

The touch panel houses the control menu and function controls. The touch keypads are very sensitive and require only a light touch to activate. Scroll up, down, left, or right to explore the different options and features.
For more information about the individual controls, see their respective sections in this manual.

Display

The display is for both the menu and oven function controls. The touch panel allows you to scroll through the oven menus. The display is very sensitive and requires only a light touch to activate and control.
When an oven is in use, the display will show the clock, mode, oven temperature, kitchen timer, and oven timer, if set. If the oven timer is not set, you can set it from this screen.
After approximately 2 minutes of inactivity, the display will go into sleep mode and the display will dim. When the oven is in operation, the display will remain bright.
During use, the display will show menus and the appropriate selections for the options being chosen.

Display Navigation

If the oven is off, touch the Oven Power to activate the menu. From this screen, all automatic cooking programs can be activated, all manual cooking programs can be set, options can be adjusted, and instructions, preparation, and tips can be accessed.

How To Use The Touch Display
  • To scroll through a menu or a list:
  • Simply swipe your finger across the display to scroll through the items or values.
  • To select or confirm:
  • Tap the screen to select the value or menu item you require. To go back to the previous screen Tap <
  • To confirm a setting or go to the next screen: Tap “SET” or “NEXT”.
First Time Use

You will need to configure the product when you switch on the appliance for the first time.
The settings can be changed subsequently by pressing access the “Tools” menu.
Or tap “SKIP” to connect your product later.
To set up the Wi-Fi connection, refer to the Connected Guide provided with the appliance.

SELECT THE LANGUAGE

  • You will need to set the language and the time when you switch on the appliance for the first time.
  • Swipe across the screen to scroll through the list of available languages.

  • Tap the language you require.

Tapping < will take you back to the previous screen.

SETTING UP WIFI

  • To enable the appliance to be controlled remotely, you will need to complete the connection process successfully first.
  • This process is necessary to Register your appliance and connect it to your home network.
  • To enable the appliance to be controlled remotely, you will need to complete the connection process successfully first.
  • This process is necessary to Register your appliance and connect it to your home network.

  • Or tap “SKIP” to connect your product later.
  • To set up the Wi-Fi connection, refer to the Connected Guide provided with the appliance.

SETTING THE TIME AND DATE

  • Connecting the oven to your home network will set the time and date automatically. Otherwise you will need to set them manually.
  • Tap the relevant numbers to set the time and the AM/PM button on the bottom-left.

Tap “SET” to confirm

Once you have set the time, you will need to set the date.

  • Tap the relevant numbers to set the date.
  •  Tap “SET” to confirm.

SET THE POWER CONSUMPTION

  • The oven is programmed to consume a level of electrical power that is compatible with a domestic network that has a rating of more than 3 kW (16 A): If your household uses a lower power, you will need to decrease this value (13 A).
  • Tap the value on the right to select the power.

Tap “OKAY” to complete initial setup.

HEAT THE OVEN

A new oven may release odors that have been left behind during manufacturing: this is completely normal.
Before starting to cook food, we therefore recommend heating the oven with it empty in order to remove any possible odors.
Remove any protective cardboard or transparent film from the oven and remove any accessories from inside it.
Heat the oven to 390°F for around one hour.
It is advisable to air the room after using the appliance for the first time.

Daily Use

SELECT A FUNCTION

  • To switch on the oven, press screen.
  • The display allows you to choose between Manual and Assisted Cooking.
  • Tap the main function you require to access the corresponding menu.
  •  Scroll up or down to explore the list.

Select the function you require by tapping it.

SET MANUAL FUNCTIONS
After having selected the function you require, you can change its settings. The display will show the settings that can be changed.

TEMPERATURE / BROIL LEVEL
Scroll through the suggested values and select the one you require.
If allowed by the function, you can tap to activate preheating.

To start setting the duration, tap “Set Cook Time”

 

Tap the relevant numbers to set the cooking time you require.

  •  To confirm tap “ NEXT”.
  •  To change the entered cooking duration time, tap on the displayed cooking timer, edit with the new time and tap
    “RESUME”.
  • To cancel a set cooking duration time, tap the duration and then select” STOP”.

SET START / END TIME DELAY
You can delay cooking before starting a function: The function will start or end at the time you select in advance.
Tap “DELAY” to set the start time or end time you require.

  •  Once you have set the required delay, tap “START DELAY” to start the waiting time.
  •  Place the food in the oven and close the door: The function will start automatically after the period of time that has been calculated.
  • Programming a delayed cooking start time will disable the oven preheating phase: The oven will reach the required temperature gradually, meaning that cooking times will be slightly longer than those listed in the cooking table.
  • To activate the function immediately and cancel the programmed delay time, tap

START THE FUNCTION

  • Once you have configured the settings, tap “START” to activate the function. You can change the values that have been set at any time during cooking by tapping the value you want to amend.
  • If the oven is hot and the function requires a specific maximum temperature, a message will be shown on the display.
  • Press X to stop the active function at any time.

PREHEATING

If previously activated, once the function has been started the display indicates the status of preheating phase.
If you did not enter the cooking time in the previous steps, you can always press on the “SET COOK TIME” icon and enter the desired time. Tap on “NEXT” to confirm.

Once this phase has been finished, an audible signal will sound and the display will indicate that the oven has reached the set temperature.

 

  •  Open the door Place the food in the oven.
  • Close the door and tap “DONE” to start cooking.
  • Placing the food in the oven before preheating has finished may have an adverse effect on the final cooking result.
  • Opening the door during the preheating phase will pause it. The cooking time does not include a preheating phase.

END OF COOKING

An audible signal will sound and the display will indicate that cooking is complete.
With some functions, once cooking has finished you can give your dish extra browning, extend the cooking time or save the function as a favorite.

  • TAP to save it as a favorite.
  • Select “Extra Browning” to start a five-minute browning cycle.
  • TAP + to save prolong the cooking.

COOKING MODES

Manual Cooking

To set a Manual Cooking Function, follow these steps.

  •  Press the Oven Power keypad.
  •  Select the Cooking Modes option.
  • Select the desired cooking function from the list. See the following table for descriptions.
  •  Follow the on-screen prompts to set the temperature, optional cook time, and optional delay start, if available. Some cooking functions allow you to turn on/off the
  • Preheat function. Some cooking functions have preset options for specific food types. Select the food type that most closely matches your recipe.
  •  Press START to begin. If preheating is on, a tone will sound when preheating is complete.
  •  Press the Oven Cancel keypad when finished cooking.

Rack Cooking


The Favorites feature stores the oven mode and temperature for your favorite recipe. As you continue to utilize your Favorites tool, your product will refine and tailor suggestions towards your cooking cravings/needs.
NOTE: A select set of Favorites and suggestions may be automatically shown on the Home screen based on your meal times.
To save a recipe, select the Favorites keypad and follow the prompts on the screen to customize your favorites.
Add an image or name to the favorite to customize it to your preferences.

Frozen Bake

The Frozen Bake function automatically selects the ideal cooking temperature and mode for 5 different types of ready frozen foods. The oven does not have to be preheated.
Consult food package for manufacturer’s instructions on cooking time.
Because of the variation of the frozen food category, it might
be necessary to prolong the cooking time in order to obtain the best result. Use the “+” button to prolong the cooking time by
2 minutes, 1 minute or 30 seconds.
Frozen bake instructions

NOTE: In case of sub-optimal cooking results, try a different wire shelf level.

Assisted Cooking
  • Assisted cooking helps you select the right mode for your everyday cooking needs.
  • Some modes allow you to skip preheat. Follow the prompts on screen for guidance throughout the cooking process.
  • Assisted cooking recipes include
  •  Casseroles & Baked Pasta
  •  Meat
  •  Fish & Seafood
  •  Vegetables
  •  Cake & Pastries
  •  Quiche
  •  Pizza
  • Three selections: Frozen Pizza, Thin Crust, and Thick Crust Pizza (Freshly Handmade or Thawed)
  •  Under Thin/Thick Crust, use the slider to select the type of tray. Use Round for round pizzas and Tray for rectangular pizza.
  •  Under Frozen, there are options for 1 layer (1 pizza) vs 4 layers (more than one pizza). You can have up to 4 pizzas on different rack positions.
  • Additional racks can be purchased, see section “Accessories”.
Doneness

NOTE: Can only be used on selected functions.

  1. Switch on the oven by selecting the ON/HOME button or touching the display.
  2.  Select the Assisted Cooking.
  3. Select the Food list.
  4. Choose the food to cook from the list.
  5. Food thickness (inches) or food weight (ounces) might be required for some foods, as a parameter for the assisted function.
  6. 6. External surface browning might be required for some foods. Select between LIGHT, NORMAL, etc. The external browning selection will prolong/reduce the final broiling stage of cooking.
  7. Press START to begin the preheat cycle.

Browning setting recipes include

  • Potatoes
  •  Quiche
  •  Hamburger
  •  Other vegetables
Settings

The Settings keypad allows you access to functions and customization options for your oven. These settings allow you to set the clock, turn the audible signals and prompts on and off, adjust the oven calibration, change the language, and more.
Select  the Settings keypad to view the Settings features:

  •  Kitchen Timer
  •  Light
  •  Self Clean (available on single ovens and the double oven upper cavity)
  • Mute

Control Lock
The Control Lock locks the control panel keypads to avoid unintended use of the oven(s). The Control Lock will remain set after a power failure, if set before the power failure occurs. When the control is locked, only the Oven Power and Settings keypads will function.
The Control Lock is preset unlocked, but can be locked.

To Lock or Unlock Control

  1. Check that the oven is off.
  2.  Select CONTROL LOCK.
  3. “Control Lock” will display.
  4. Scroll up to unlock. No keypads will function.

Preferences

Times and Dates
Set time and date preferences.

  •  Your Meal Times: Adjust when breakfast/lunch/dinner is shown
  • Time
  •  Date
  •  Time Format (AM/PM vs 24 hour [Military Time])
  • Sound Volume
  • Set sound volume preferences.
  • Timers and Alerts
  •  Buttons and Effects
  • Display Settings
  • Set the screen brightness.
  •  Display Brightness
  • Regional
  • Set regional preferences.
  •  Language: English or French

Info

  • Service and Support: Displays model number, Customer Support contact info, and Diagnostics.
  • Restore Factory: This will restore your product to the original factory default settings.
Sabbath Mode

The Sabbath Mode sets the oven to remain on in a bake setting until disabled.
When the Sabbath Mode is activated, only the Bake cycle will operate. All other cooking and cleaning cycles are disabled. No tones will sound, and the displays will not indicate temperature changes. When the oven door is opened or closed, the oven light will not turn on or off, and the heating elements will not turn on or off immediately.
If a cook timer is set, the countdown will appear. The timer will countdown once the timer is set.
NOTE: If a power failure happens while Sabbath Mode is running, the oven will show Sabbath Mode is on, but the Bake cycle will not be on. If the oven door is opened during this time, the oven light will not turn on.
To enable and activate Sabbath Mode

  1. Press the Settings keypad.
  2. Select MORE MODES.
  3.  Select SABBATH MODE.
  4. Press SABBATH MODE again to enable Sabbath Mode (Sabbath Mode is preset to off).
  5. (Optional) For timed cooking in Sabbath Mode, press ADD A COOK TIME, enter the desired cook time and then press NEXT.
  6.  Select START

To Disable and Exit Sabbath Mode

  1. Press the Oven Power or Cancel Keypad.
  2. Press and hold the display screen for three seconds.

To Adjust Temperature

1. Press the +/- 25 on the display screen to select the new temperature.
NOTE  The temperature adjustment will not appear on the display, and no tones will sound.

Aluminum Foil

The temperature adjustment will not appear on the display, and no tones will sound.

IMPORTANT  To avoid permanent damage to the oven bottom finish, do not line the oven bottom with any type of foil or liner.
For best cooking results, do not cover entire oven rack with foil because air must be able to move freely.
To catch spills, place foil on rack below dish. Make sure foil is at least 1/2″ (1.3 cm) larger than the dish and that it is turned up at the edges.

Broiling

When broiling, no preheating is necessary unless recommended otherwise in the recipe. Position food on rack above a drip tray, and then place it in the center of the oven rack. Close the oven door to ensure proper broiling temperature.
NOTE: Odors and smoke are normal the first few times the oven is used or if the oven is heavily soiled.
Changing the temperature when broiling allows more precise control when cooking. The lower the broil setting, the slower the cooking. Thicker cuts and unevenly shaped pieces of meat, fish and poultry may cook better at lower broil settings. Refer to the “Positioning Racks and Bakeware” section for more information.
On lower settings, the broil element will cycle on and off to maintain the proper temperature.

FOOD RACK POSITION

Most broiling       5

For hamburger patties to have a well-seared exterior and a rare interior, use a flat rack in position 5. Cook over a drip tray filled with 2 cups (500 ml) of water. Broil for 15-30 minutes and turn two thirds of the way through cooking.

Traditional Cooking

NOTE Additional racks may be required for multi-rack cooking.

Bakeware

To cook food evenly, hot air must be able to circulate. Allow 2″ (5.0 cm) of space around bakeware and oven walls.
Use the following chart as a guide.

Preheating and Oven Temperature

Preheating
When beginning a Bake cycle, the oven will begin preheating after Start is pressed. Remember to select the preheat icon in the upper right corner of temperature select screen to enable preheat. The oven will take approximately 6 minutes to reach 350°F (177°C) with all of the oven racks provided with your oven inside the oven cavity. Higher temperatures will take longer to preheat. The preheat cycle rapidly increases the oven temperature. The actual oven temperature will go above your set temperature to offset the heat lost when your oven door is opened to insert food. This ensures that when you place your food in the oven, the oven, will begin at the proper temperature. Insert your food when the preheat tone sounds. Do not open the door during preheat before the tone sounds.

Rapid Preheat
Rapid Preheat can be used to shorten the preheating time. Only one standard flat oven rack should be in the oven during Rapid Preheat. Extra racks should be removed prior to starting. The preheating cycle should be completed before placing food in the oven. When the Rapid Preheat cycle is complete, the oven starts a normal Bake cycle.
IMPORTANT Rapid Preheat should be used only for one-rack baking.

Oven Temperature
While in use, the oven elements will cycle on and off as needed to maintain a consistent temperature, but they may run slightly hot or cool at any point in time due to this cycling. Opening the oven door while in use will release the hot air and cool the oven which could impact the cooking time and performance. It is recommended to use the oven light to monitor cooking progress.
Before baking and roasting, position racks according to the “Positioning Racks and Bakeware” section. When roasting, it is not necessary to wait for the oven preheat cycle to end before putting food in unless it is recommended in the recipe.

Baking and Roasting

The oven will take approximately 6 minutes to reach 350°F (177°C) with all oven racks inside the oven cavity. The preheat cycle rapidly increases the temperature inside the oven cavity.
Higher temperatures will take longer to preheat. Factors that impact preheat times include room temperature, oven temperature, and the number of racks. Unused oven racks
can be removed prior to preheating your oven to help reduce preheat time. The actual oven temperature will go above the set temperature to offset the heat lost when the oven door is opened to insert food. This ensures that the oven will begin at the proper temperature when you place food in the oven. Insert food when the preheat tone sounds. Do not open the door during preheat until the tone sounds.
During baking or roasting, the bake and broil elements will cycle on and off in intervals to maintain the oven temperature.
Depending on the model, if the oven door is opened during baking or roasting, the heating elements (bake and broil) will turn off approximately 30 seconds after the door is opened. They will turn on again approximately 30 seconds after the door is closed.

Accessories

The number and the type of accessories may vary depending on which model is purchased. Other accessories can be purchased separately, see “Assistance or Service” section.

Use to cook food or as a support for pans, cake tins and other ovenproof items of cookware.

Use as an oven tray for cooking meat, fish, vegetables, focaccia, etc. or position underneath the wire shelf to collect cooking juices. Use for cooking all bread and pastry products, but also for roasts and fish.

Oven Care

Self Cleaning Cycle

IMPORTANT The health of some birds is extremely sensitive to the fumes given off during the Self Cleaning cycle. Exposure to the fumes may result in death to certain birds. Always move birds to another closed and well-ventilated room.
Self clean the oven before it becomes heavily soiled. Heavy soil results in longer cleaning and more smoke.
Keep the kitchen well-ventilated during the Self Cleaning cycle to help get rid of heat, odors, and smoke.
Do not block the oven vent(s) during the Self Cleaning cycle.
Air must be able to move freely. See the “Oven Vents” section.
Do not clean, rub, damage, or move the oven door gasket.
The door gasket is essential for a good seal.

Prepare Oven

  • Remove the broiler pan, grid, cookware and bakeware.
  •  Remove oven racks to keep them shiny and easy to slide. See the “General Cleaning” section for more information.
  •  Remove any foil from the oven because it may burn or melt, damaging the oven.
  •  Hand clean inside door edge and the 11/2″ (3.8 cm) area around the inside oven cavity frame, being certain not to move or bend the gasket. This area does not get hot enough during high-temp self cleaning to remove soil. Do not let water, cleaner, etc., enter slots on door frame. Use a damp cloth to clean this area.
  • Wipe out any loose soil to reduce smoke and avoid damage. At high temperatures, foods react with porcelain. Staining, etching, pitting, or faint white spots can result. This is normal and will not affect cooking performance.
  • IMPORTANT: Before starting self clean, switch remote control to OFF by selecting the dedicated button on the control panel. For Double Oven, the self-clean feature is only available in the upper oven

How the Cycle Works
IMPORTANT  The heating and cooling of porcelain on steel in the oven may result in discoloring, loss of gloss, hairline cracks, and popping sounds.
The Self Cleaning cycle uses very high temperatures, burning soil to a powdery ash.
Suggested clean times are 1 hour and 15 minutes for light soil, 1 hour and 40 minutes for medium soil and 2 hours for heavy soil.
Once the oven has completely cooled, remove ash with a damp cloth. To avoid breaking the glass, do not apply a cool damp cloth to the inner door glass before it has completely cooled.
The oven lights will not work during the Self Cleaning cycle.

NOTE
The oven has a two-speed cooling fan motor. During the Self Cleaning cycle, the fan(s) will operate at its highest speed to increase airflow to better exhaust the hotter air through the oven vent(s). An increase in noise may be noticeable during and after the Self Cleaning cycle until the oven cools.
Before Self Cleaning, make sure the door is closed completely or it will not lock and the cycle will not begin. When the oven is locked, the doors of the oven cannot be opened. To avoid damage to the doors, do not force the doors open when the oven is locked.

  1. Touch the Settings keypad.
  2. Select the Self Clean icon.
  3. Select type of Self Cleaning:
  4. Light: 1 hour and 15 minutes
  5. Medium: 1 hour and 40 minutes
  6. Heavy: 2 hours
  7. Follow the prompts on the oven display to prepare the oven.
  8. Select START to begin the cleaning process.
    OR
    Select DELAY START to set a delayed Self Cleaning cycle. See the “To Delay Start Self Cleaning Cycle” Section.
    The oven doors will automatically lock.
    NOTE: It may take a couple moments for the oven door to automatically lock after starting the Self Clean Cycle.
    When the self cleaning cycle is complete and the oven cools, the oven doors will unlock.

6. When the oven is completely cooled, remove ash with a damp cloth

To Delay Start Self Cleaning Cycle

Follow steps 1 through 4 above, then

  1. Select DELAY START.
  2. Select the start time of when the Self Cleaning cycle should begin by scrolling from left to right.
  3.  Select START DELAY.
    The oven doors will automatically lock after the Delay Start countdown.
    When the Self Cleaning cycle is complete and the oven cools, the oven doors will unlock.
  4. When the oven is completely cooled, remove ash with a damp cloth.

To Stop Self Cleaning Anytime

Touch the Oven Cancel Keypad. If the oven temperature is too high, the door will remain locked. It will not unlock until the oven cools.

General Cleaning

IMPORTANT Before cleaning, make sure all controls are off and the oven is cool. Always follow label instructions on cleaning products. For additional information, you can visit the Frequently Asked Questions (FAQs) section of our website at www.whirlpool.com. In Canada, refer to the Customer Service section at www.whirlpool.ca
Soap, water, and a soft cloth or sponge are suggested first unless otherwise noted.

EXTERIOR PORCELAIN ENAMEL SURFACES (on some models)

Food spills containing acids, such as vinegar and tomato, should be cleaned as soon as the entire oven is cool. These spills may affect the finish.

Cleaning Method

  •  Glass cleaner, mild liquid cleaner or nonabrasive scrubbing pad:
    Gently clean around the model/serial/rating plate because scrubbing may remove numbers.
  • Affresh® Kitchen and Appliance Cleaner Part Number W10355010 (not included):
    See the “Accessories” section for more information.

STAINLESS STEEL (on some models)

NOTE: To avoid damage to stainless steel surfaces, do not use soap-filled scouring pads, chlorine bleach, abrasive cleaners, steel-wool pads, gritty washcloths or abrasive paper towels. Damage may occur to stainless steel surfaces, even with one-time or limited use.

Cleaning Method
Rub in direction of grain to avoid damaging Affresh® Stainless Steel Cleaner Part Number W10355016: See the “Accessories” section for more information.

METALLIC PAINT (on some models)
Do not use abrasive cleaners, cleaners with bleach, rust removers, ammonia or sodium hydroxide (lye) because paint surface may stain.

CONTROL PANEL AND OVEN DOOR EXTERIOR
To avoid damage, do not use abrasive cleaners, steel-wool pads, gritty washcloths, or abrasive paper towels.
Cleaning Method

  • Glass cleaner and soft cloth or sponge:
    Apply glass cleaner to soft cloth or sponge, not directly on panel.
  • Affresh® Kitchen and Appliance Cleaner Part Number W10355010 (not included):
    See the “Accessories” section for more information.

OVEN RACKS

Cleaning Method

  • Steel-wool pad
  • For racks that have discolored and are harder to slide, a light coating of vegetable oil applied to the rack guides will help them slide.

OVEN CAVITY AND OVEN DOOR INTERIOR
Do not use oven cleaners.
Food spills should be cleaned after the oven cools. At high temperatures, foods react with porcelain and staining, etching, pitting, or faint white spots can result.
Cleaning Method:

  • Self Cleaning cycle:
    See the “Self Cleaning Cycle” section first.
  • For optimal door cleaning results, wipe away any deposits with a damp sponge before running cycle.
Oven Lights

The oven light(s) are standard 25 W appliance bulbs.
Before replacing, make sure the oven is cool and the controls are turned off.
To Replace:

  1. Disconnect power.
  2. Open oven door.
  3. Remove the sliding runners (if present), then remove the shelf guides.
  4. Use a screwdriver to pry off the light cover.
  5. Replace the light bulb.
  6. Place the light cover back in place. Push firmly until it snaps into position.
  7. Refit the shelf guides.
  8. Reconnect power.

TROUBLESHOOTING

First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call, refer to the warranty, or visit producthelp.whirlpool.com. In Canada, visit www.whirlpool.ca.
Contact us by mail with any questions or concerns at the address below:
In the U.S.A.:
Whirlpool Brand Home Appliances Customer eXperience Center 553 Benson Road
Benton Harbor, MI 49022-2692
In Canada:
Whirlpool Brand Home Appliances Customer eXperience Centre 200 – 6750 Century Ave. Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

ASSISTANCE OR SERVICE

If you need service
Please refer to the warranty.

If you need replacement parts
If you need to order replacement parts, we recommend that you use only factory specified parts. These factory specified parts will fit right and work right because they are made with the same precision used to build every new Whirlpool® appliance.
To locate factory specified parts in your area, call us or your nearest Whirlpool designated service center.

In the U.S.A.
Call the Whirlpool Customer eXperience Center toll-free:
1-866-698-2538 or visit our website at www.whirlpool.com.
Our consultants provide assistance with:

  • Features and specifications on our full line of appliances.
  • Installation information.
  • Use and maintenance procedures.
  • Repair parts sales.
  • Specialized customer assistance (Spanish speaking, hearing impaired, limited vision, etc.).
  • Referrals to local dealers, repair parts distributors and service companies. Whirlpool designated service technicians are trained to fulfill the product warranty and provide after-warranty service anywhere in the United States.
    To locate the Whirlpool designated service company in your area, you can also look in your telephone directory Yellow Pages.

For further assistance
If you need further assistance, you can write with any questions or concerns at:
Whirlpool Brand Home Appliances
Customer eXperience Center 553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.

In Canada
Call the Whirlpool Canada Customer eXperience Centre toll-free: 1-800-807-6777, or visit our website at www.whirlpool.ca.
Our consultants provide assistance with:

  • Use and maintenance procedures.
  • Repair parts sales.
  • Referrals to local dealers, repair parts distributors and service companies. Whirlpool designated service technicians are trained to fulfill the product warranty and provide after-warranty service anywhere in Canada.

For further assistance
If you need further assistance, you can write with any questions or concerns at:
Whirlpool Brand Home Appliances
Customer eXperience Centre
200 – 6750 Century Ave.
Mississauga, ON L5N 0B7
Please include a daytime phone number in your correspondence.

Accessories
To order accessories, visit our website at www.whirlpool.com.
Drip Tray
Order Part Number W11229219
Baking Tray
Order Part Number W11229218
Wire Shelf
Order Part Number W10886770