Sony HT-SD40 Bluetooth Sound Bar Instruction Manual

HT-SD40 Bluetooth Sound Bar

Sound Bar
Operating Instructions
HT-SD40
WARNING
Do not install the speaker system in a confined space, such as a bookcase or built-in cabinet.
To reduce the risk of fire, do not cover the ventilation opening of the speaker system with newspapers, tablecloths, curtains, etc. Do not expose the speaker system to naked flame sources (for example, lighted candles).
To reduce the risk of fire or electric shock, do not expose this speaker system to dripping or splashing, and do not place objects filled with liquids, such as vases, on the speaker system.
The speaker system is not disconnected from the mains as long as it is connected to the AC outlet, even if the speaker system itself has been turned off.
As the mains plug is used to disconnect the speaker system from the mains, connect the speaker system to an easily accessible AC outlet. Should you notice an abnormality in the speaker system, disconnect the mains plug from the AC outlet immediately.
CAUTION
Risk of explosion if the battery is replaced by an incorrect type. Do not expose batteries or appliances with battery-installed to excessive heat, such as sunshine and fire.
Do not place this product close to medical devices.
This product (including accessories) has magnet(s) which may interfere with pacemakers, programmable shunt valves for hydrocephalus treatment, or other medical devices. Do not place this product close to persons who use such medical devices. Consult your doctor before using this product if you use any such medical device.
Indoor use only.
Recommended cables
Properly shielded and grounded cables and connectors must be used for connection to host computers and/or peripherals.
For the bar speaker
The nameplate is located on the bottom of the bar speaker.
This equipment has been tested and found to comply with the limits set out in the EMC regulation using a connection cable shorter than 3 meters.
For customers in Europe Notice for customers: the following information is only applicable to equipment sold in countries applying EU directives and/or UK applying relevant statutory requirements
This product has been manufactured by or on behalf of Sony Corporation.
EU and UK Importer: Sony Europe B.V.
Inquiries to the EU Importer or related to product compliance in Europe should be sent to the manufacturer’s authorized representative, Sony Belgium, bijkantoor van Sony Europe B.V., Da Vincilaan 7-D1, 1930 Zaventem, Belgium. Inquiries to the UK Importer or related to product compliance in the UK should be sent to the manufacturer’s authorized representative, Sony Europe B.V., The Heights, Brooklands, Weybridge, Surrey KT13 0XW, United Kingdom.
Hereby, Sony Corporation declares that this equipment is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://compliance.sony.eu
Hereby, Sony Corporation declares that this equipment is in compliance with the UK relevant statutory requirements. The full text of the declaration of conformity is available at the following internet address: https://compliance.sony.co.uk
This radio equipment is intended to be used with the approved version(s) of software that are indicated in the Declaration of Conformity. The software loaded on this radio equipment is verified to comply with the essential requirements of the Radio Equipment Regulations. The software version can be found by following procedure.

5-034-824-11 (2)
1 Press and hold SOUND FIELD on the remote
control for more than 5 seconds.
The stream information appears in the front panel display.
2 Press (volume) +/­ on the remote control
to display the software version in the front panel display.
Disposal of waste batteries and electrical and electronic equipment (applicable in the European Union and other countries with separate collection systems)
This symbol on the product, the battery or on the packaging indicates that the product and the battery shall not be treated as household waste. On certain batteries this symbol might be used in combination with a chemical symbol. The chemical symbol for lead (Pb) is added if the battery contains more than 0.004% lead. By ensuring that these products and batteries are disposed of correctly, you will help to prevent potentially negative consequences for the environment and human health which could be caused by inappropriate waste handling. The recycling of the materials will help to conserve natural resources. In case of products that for safety, performance or data integrity reasons require a permanent connection with an incorporated battery, this battery should be replaced by qualified service staff only. To ensure that the battery and the electrical and electronic equipment will be treated properly, hand over these products at end-of-life to the appropriate collection point for the recycling of electrical and electronic equipment. For all other batteries, please view the section on how to remove the battery from the product safely. Hand the battery over to the appropriate collection point for the recycling of waste batteries. For more detailed information about recycling of this product or battery, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product or battery.
This equipment should be installed and operated keeping the radiator over 20 cm away from person’s body.
Precautions
On safety · Should any solid object or liquid fall into the
speaker system, unplug the speaker system and have it checked by qualified personnel before operating it any further. · Do not climb on the speaker system, as you may fall down and injure yourself, or speaker system damage may result.
On power sources · Before operating the speaker system, check that
the operating voltage is identical to your local power supply. The operating voltage is indicated on the nameplate on the bottom of the bar speaker. · If you are not going to use the speaker system for a long time, be sure to disconnect the speaker system from the wall outlet (mains). To disconnect the AC power cord (mains lead), grasp the plug itself; never pull the cord. · One blade of the plug is wider than the other for the purpose of safety and will fit into the wall outlet (mains) only one way. If you are unable to insert the plug fully into the outlet, contact your dealer. · The AC power cord (mains lead) must be changed only at a qualified service shop.
On heat buildup Although the speaker system heats up during operation, this is not a malfunction. If you continuously use this speaker system at high volume, the speaker system temperature at the rear and bottom rises considerably. To avoid burning yourself, do not touch the speaker system.
On placement · Place the speaker system in a location with
adequate ventilation to prevent heat buildup and prolong the life of the speaker system. · Do not place the speaker system near heat sources or in a place subject to direct sunlight, excessive dust, or mechanical shock. · Do not place anything on the top of the bar speaker. · If the speaker system is being used in combination with a TV, VCR, or tape deck, noise may result and picture quality may suffer. In such a case, place the speaker system away from the TV, VCR, or tape deck. · Use caution when placing the speaker system on a surface that has been specially treated (with wax, oil, polish, etc.), as staining or discoloration of the surface may result. · Take care to avoid any possible injury from the corners of the bar speaker.
On operation Before connecting other equipment, be sure to turn off and unplug the speaker system.

If you encounter color irregularity on a nearby TV screen Color irregularities may be observed on certain types of TV. · If color irregularity is observed…
Turn off the TV, then turn it on again after 15 to 30 minutes. · If color irregularity is observed again… Place the speaker system further away from the TV. On cleaning · Clean the speaker system with a soft, dry cloth. Do not use any type of abrasive pad, scouring powder, or solvent such as alcohol or benzine. If you have any questions or problems concerning your speaker system, please consult your nearest Sony dealer.
About These Operating Instructions
· The instructions in these Operating Instructions describe the controls on the remote control.
· Some illustrations are presented as conceptual drawings, and may be different from the actual products.
· Characters in brackets [ ] appear in the front panel display.
Installation and Connection
Connecting a TV with an HDMI Cable and/or Optical Cable
Refer to Startup Guide (separate document).
Mounting the Bar Speaker on a Wall
You can mount the bar speaker on a wall.
Notes · Prepare screws (not supplied) that are suitable for the wall
material and strength. As a plasterboard wall is especially fragile, attach the screws securely in the wall beam. Install the bar speaker horizontally, hung by screws in studs in a continuous flat section of the wall. · Have the installation done by a Sony dealer or licensed contractor and pay special attention to safety during the installation. · If using a cable with a large plug, it may not be possible to mount the bar speaker on a wall. · Sony shall not be held responsible for accidents or damage caused by improper installation, insufficient wall strength, improper screw installation, natural disasters, etc.
1 Prepare two screws (not supplied) that are
suitable for the wall mount holes on the rear of the bar speaker.
4 mm
30 mm or more
5.1 mm
10 mm
Hole on the rear of the bar speaker
2 Align the vertical line above the ” TV
CENTER LINE” printed on the WALL MOUNT TEMPLATE (supplied) with the center of the width of your TV.
Center of the TV
WALL MOUNT TEMPLATE
3 Align the ” TV BOTTOM LINE” printed on
the WALL MOUNT TEMPLATE with the bottom of your TV, then adhere the WALL MOUNT TEMPLATE on the wall with a commercially available adhesive tape, etc.
Adhesive WALL MOUNT tape, etc. TEMPLATE
4 Fasten the screws prepared in step 1 securely
into the screw marks () on the ” SCREW LINE” printed on the WALL MOUNT TEMPLATE.
737 mm
368.5 mm 368.5 mm
Marks () Screws
10.5 mm to 11.5 mm
5 Remove the WALL MOUNT TEMPLATE. 6 Hang the bar speaker on the screws.
Align the holes on the rear of the bar speaker with the screws, then hang the bar speaker on the two screws.
Note When sticking WALL MOUNT TEMPLATE, smooth it out fully.

Connecting the Subwoofer Manually
If you cannot connect the subwoofer to the speaker system, or you use multiple wireless products and want to specify the wireless connection to link the speaker system to the subwoofer, perform the manual connection.
LINK
Power indicator
(BLUETOOTH) button + (volume) button
1 Press and hold (BLUETOOTH) and + (volume)
on the bar speaker for more than 5 seconds. [SECURE LINK] appears, then[LINK] flashes in the front panel display. To cancel the manual connection, press and hold (BLUETOOTH) and + (volume) on the bar speaker for more than 5 seconds again.
2 Press LINK on the subwoofer.
The manual connection starts. The power indicator of the subwoofer flashes in amber.
3 Make sure that [DONE] appears in the front
panel display. The manual connection is established and the power indicator of the subwoofer lights in amber. Note
If [ERROR] appears in the front panel display, the connection of the subwoofer has not been established. Perform the manual connection again.
Parts and Controls
Bar Speaker
Front
(power) button Turns on the speaker system or sets it to standby mode.
(TV) button (BLUETOOTH) button +/­ (volume) buttons BLUETOOTH indicator
— Flashes twice in blue: During pairing standby status
— Flashes in blue: BLUETOOTH connection is being attempted.
— Lights in blue: BLUETOOTH connection has been established.
Front panel display Remote control sensor
Point the remote control at the remote control sensor to operate the speaker system. Rear
AC inlet HDMI OUT (TV (ARC)) jack
Connect a TV that has an HDMI input jack with an HDMI cable. The speaker system is compatible with Audio Return Channel (ARC). ARC is the function that sends TV sound to an AV device such as the speaker system from the TV’s HDMI jack. TV IN (OPTICAL) jack IR repeater Transmits the remote signal of the TV remote control to the TV. UPDATE port Connect the USB memory when updating the speaker system.

Subwoofer
Power indicator — Lights in green: The subwoofer is connected to the speaker system. — Lights in red: The subwoofer is in standby mode. — Lights in amber: The subwoofer is connected to the speaker system with the manual connection. — Flashes slowly in green: The subwoofer is attempting to connect to the speaker system. — Flashes slowly in amber: The subwoofer is attempting to connect to the speaker system with the manual connection. — Flashes twice in amber: The subwoofer is in pairing standby status with the manual connection. — Flashes quickly in amber: The software is updating. — Turns off: The subwoofer is turned off.
(power) button Turns on or off the subwoofer.
LINK button AC inlet
Remote Control
Some buttons function differently depending on how long the button is pressed. This section explains the functions when pressed shortly. For details about other functions, refer to “Changing the Settings” on the back page.
INPUT Selects the input for playback on the speaker system. Each time you press INPUT, the input source toggles between the TV and BLUETOOTH input.
SOUND FIELD Turns on/off the surround effect.
(volume) +*/­ Adjusts the volume.
BASS +/­ Adjusts the subwoofer volume.
(power) Turns on the speaker system or sets it to standby mode.
VOICE Turns on/off the voice mode.
NIGHT Turns on/off the night mode.
(muting) Mutes the sound temporarily.
* The (volume) + button has a tactile dot. Use it as a guide during operation.
About the replacement of batteries for the remote control When the speaker system does not respond by operating with the remote control, replace two batteries with new batteries. Use R03 (size AAA) manganese batteries for replacement.

Listening to Music/Sound
Listening to a TV Connected with an HDMI Cable (ARC) or Optical Digital Cable
You can listen to TV sound on the speaker system.
INPUT
(volume) +/­
BASS +/­
1 Press INPUT repeatedly to select [TV] in the
front panel display.
2 Adjust the volume.
· Adjust the volume by pressing (volume) +/­ on the remote control.
· Adjust the subwoofer volume by pressing BASS +/­ on the remote control.
Note When you connect the TV to both the HDMI OUT (TV (ARC)) and TV IN (OPTICAL) jacks, the jack for audio input is selected depending on which audio signal is input first. Tip You can also select the input by pressing (TV) on the bar speaker.
Listening to Music from a Mobile Device with the BLUETOOTH® Function
You can listen to music stored on a mobile device such as a smartphone or tablet via wireless connection by connecting the speaker system and the mobile device with the BLUETOOTH function. When connecting to the mobile device with the BLUETOOTH function, you can perform operations simply through the speaker system without turning the TV on.
Listening to Music by Pairing with a Mobile Device
You need to perform pairing of the speaker system and mobile device by using the BLUETOOTH function. Pairing is the process required to mutually register the information on BLUETOOTH devices to be connected wirelessly in advance.
(volume) +/­
BASS +/­
1 Press and hold (BLUETOOTH) on the bar
speaker for 2 seconds. (BLUETOOTH)
button
2 Make sure that the BLUETOOTH indicator on
the bar speaker flashes twice repeatedly in blue and [PAIRING] appears in the front panel display. The speaker system enters the pairing mode.
3 On the mobile device, search for the speaker
system by performing the pairing operation. The list of the BLUETOOTH devices that are detected appears on the screen of the mobile device. For the operation method to pair the BLUETOOTH device to the mobile device, refer to the operating instructions of the mobile device.
4 Pair the speaker system and mobile device by
selecting “HT-SD40” from the list on the screen of the mobile device. If a passkey is requested, enter “0000.”
5 Make sure that the BLUETOOTH indicator on
the bar speaker lights in blue and [BT] appears in the front panel display. A connection between the speaker system and mobile device has been established.
6 Start audio playback with the music app on
the connected mobile device. Sound is output from the speaker system.
7 Adjust the volume.
· Adjust the volume by pressing (volume) +/­ on the remote control.
· Adjust the subwoofer volume by pressing BASS +/­ on the remote control.
Notes · You can pair up to 9 BLUETOOTH devices. If a 10th
BLUETOOTH device is paired, the oldest connected device will be replaced by the new one. · Perform pairing for the second and subsequent mobile devices. Tips · You can check the connection status of the BLUETOOTH function by checking the BLUETOOTH indicator status. · While the BLUETOOTH input is being selected, the speaker system enters the pairing mode by pressing (BLUETOOTH) on the bar speaker shortly.

Listening to Music from the Paired Mobile Device
INPUT
(volume) +/­
BASS +/­
1 Turn the BLUETOOTH function of the mobile
device on.
2 Press INPUT repeatedly to select [BT] or press
(BLUETOOTH) on the bar speaker shortly. The BLUETOOTH indicator flashes and the speaker system automatically reconnects to the BLUETOOTH device it was most recently connected to.
3 Make sure that the BLUETOOTH indicator on
the bar speaker lights in blue and [BT] appears in the front panel display. A connection between the speaker system and mobile device has been established.
4 Start audio playback with the music app on
the connected mobile device. Sound is output from the speaker system.
5 Adjust the volume.
· Adjust the volume by pressing (volume) +/­ on the remote control.
· Adjust the subwoofer volume by pressing BASS +/­ on the remote control.
Adjusting the Sound
Enjoying Surround Effect (SOUND FIELD)
You can turn the surround effect on or off to suit sound sources.
SOUND FIELD

1 Press SOUND FIELD to select the setting.
The setting appears in the front panel display.

Setting [SF.ON]
[SF.OFF]

Explanation
The sound is output with the surround effect. This setting is suitable for experiencing the surround sound with presence.
The sound is output without the surround effect. This setting is suitable for listening to music or news.

Making Dialogs Clearer (VOICE)

VOICE

1 Press VOICE to select the setting.
The setting appears in the front panel display.

Setting [Vo.ON]
[Vo.OFF]

Explanation
Dialog is easily heard by enhancing dialog range.
Deactivates the voice mode function.

Enjoying Clear Sound with Low Volume at Midnight (NIGHT)

NIGHT

1 Press NIGHT to select the setting.
The setting appears in the front panel display.

Setting [N.ON]
[N.OFF]

Explanation
Sound is output at low volume with minimum loss of fidelity and clarity of dialog.
Deactivates the night mode function.

Note When you turn the speaker system off, this setting is set to [N.OFF] automatically.

Using the Speaker System by Interlocking with a TV
Operating the Speaker System by Interlocking with a TV (Control for HDMI Function)
Connecting a TV compatible with the Control for HDMI function using an HDMI cable enables you to interlock the speaker system operation such as power on/off or volume adjustment with a TV.
About the Control for HDMI function The Control for HDMI function is a function that enables operation of devices connected with an HDMI (High-Definition Multimedia Interface) cable by interlocking them. Although this function works for devices compatible with the Control for HDMI function, it may not work if connecting devices other than those manufactured by Sony.
Preparing to Operate by Interlocking with a TV
Enable the Control for HDMI function settings of the TV connected to the speaker system with an HDMI cable. The default setting of the Control for HDMI function of the speaker system is [ON].
Tips · When connecting a device such as a Blu-ray Disc player to a
TV with an HDMI cable, enable its Control for HDMI function. · To enable the Control for HDMI function of a TV or Blu-ray
Disc player, refer to their operating instructions. · If you enable the Control for HDMI (“BRAVIA” sync) function
when using a TV manufactured by Sony, the Control for HDMI function of the speaker system is also enabled automatically. When the setting is complete, [DONE] appears in the front panel display.
Performing Power Operation or Volume Adjustment by a TV Remote Control
When turning the TV on/off or adjusting the volume using the TV remote control, the speaker system power operation or volume adjustment is interlocked.
Power interlocking When you turn on or off the TV, the speaker system will turn on or off automatically.
Note If you turn off the speaker system before turning off the TV, the speaker system may not turn on automatically even though you turn on the TV next time. In this case, perform the following operation. — Select the speaker system for the sound output device in
the TV menu. — When using Sony TV, turn on the speaker system while the
TV is turned on.
Volume adjustment The sound of the TV you are watching is output from the speaker system automatically. You can adjust the speaker system volume by the TV remote control.
Tip You can change the Control for HDMI settings by following procedure.
1 Press and hold VOICE on the remote control for more
than 5 seconds. [CONTROL FOR HDMI] appears in the front panel display.
2 Press (volume) +/­ on the remote control to display
the desired setting in the front panel display.
3 Wait until the displayed setting disappears from the front
panel display. The setting is fixed.
Operating the Speaker System by Interlocking with a TV Compatible with the “BRAVIA” Sync Function
“BRAVIA” Sync is an extended function developed by Sony based on the Control for HDMI function. By connecting “BRAVIA” Sync-compatible devices such as a TV using an HDMI cable, you can control the devices by interlocking them with each other.
To use “BRAVIA” Sync “BRAVIA” Sync is enabled by enabling the Control for HDMI function of the Sony device. For the operation to enable the Control for HDMI function, see “Preparing to Operate by Interlocking with a TV.”
What You Can Do with “BRAVIA” Sync
Control for HDMI function · Power interlocking · Volume adjustment
Saving Power Consumption
To use the speaker system with saving power consumption, change the following settings.
Turning the Speaker System Off by Detecting the Using State
When you set the auto standby function to on, the speaker system enters standby mode automatically when you do not operate the speaker system for about 20 minutes and the speaker system is not receiving an input signal.
1 Press and hold (power) and (TV) on the
bar speaker for more than 5 seconds. [AUTO STANDBY] and the current setting appear in the front panel display.
2 Press (volume) +/­ on the remote control
to display the desired setting in the front panel display.
3 Wait until the displayed setting disappears
from the front panel display. The setting is fixed.
Saving Power in Standby Mode
To save power consumption during the standby mode, set the BLUETOOTH standby mode and Control for HDMI function to off. To change the BLUETOOTH standby mode setting, press and hold (power), (BLUETOOTH), and ­ (volume) on the bar speaker for more than 5 seconds (the changed setting appears in the front panel display). To change the Control for HDMI function setting, press and hold VOICE on the remote control for more than 5 seconds to display the setting in the front panel display, then press (volume) +/­ on the remote control to select the desired setting.
Continued on back page

Changing the Settings

Audio Settings
Easily listening to low volume sounds.
Adjusting the volume of the connected device automatically
Selecting the sound for multiplex broadcast

You can easily listen to low volume sounds by compressing the dynamic range (the range between maximum and minimum volume) of the sound signal by setting to [ON]. This function works only when playing Dolby Digital signal. You can adjust the volume automatically depending on the input signal or contents of a connected device by setting to [ON].
You can select the sound for multiplex broadcast sound.

1 Press and hold (power), (TV), and
­ (volume) on the bar speaker for more than 5 seconds.
[DRC] and the current setting appear in the front panel display.
2 To change the setting, perform the same
operation as step 1.
The setting is fixed after the changed setting appears in the front panel display.
1 Press and hold NIGHT on the remote
control for more than 5 seconds.
[A.VOL] appears in the front panel display.
2 Press (volume) +/­ on the remote
control to display the desired setting in the front panel display.
3 Wait until the displayed setting disappears
from the front panel display.
The setting is fixed.
1 Press and hold (muting) on the remote
control for more than 5 seconds.
[DUAL] appears in the front panel display.
2 Press (volume) +/­ on the remote
control to display the desired setting in the front panel display.
3 Wait until the displayed setting disappears
from the front panel display.
The setting is fixed.

BLUETOOTH Settings

Turning the BLUETOOTH standby mode on or off

You can turn the speaker system on and start the BLUETOOTH connection automatically with the BLUETOOTH device operation while the speaker system is in standby mode by setting to [ON].

1 Press and hold (power), (BLUETOOTH),
and ­ (volume) on the bar speaker for more than 5 seconds.
[BT STANDBY] and the current setting appear in the front panel display.
2 To change the setting, perform the same
operation as step 1.
The setting is fixed after the changed setting appears in the front panel display.

Turning the BLUETOOTH function on or off

Notes · While the BLUETOOTH standby mode is on, standby
power consumption increases. · The BLUETOOTH standby mode cannot be set while the
BLUETOOTH function is off.

You can turn the BLUETOOTH 1 Press and hold (power) and

function on or off.

(BLUETOOTH) on the bar speaker for

more than 5 seconds.

[BT POWER] and the current setting appear in the front panel display.

2 To change the setting, perform the same
operation as step 1.

The setting is fixed after the changed setting appears in the front panel display.

Front Panel Display/Indicators Settings

Adjusting the brightness of the front panel display and indicators

You can change the brightness of the followings. · Front panel display on the
bar speaker · BLUETOOTH indicator on
the bar speaker · Power indicator on the
subwoofer

1 Press and hold (TV) and (BLUETOOTH)
on the bar speaker for more than 5 seconds.
[DIMMER] appears in the front panel display.
2 Press (volume) +/­ on the remote
control to display the desired setting in the front panel display.
3 Wait until the displayed setting disappears
from the front panel display.
The setting is fixed.

Note The front panel display is turned off when [OFF] is selected. It turns on automatically when you press any button, then turns off again if you do not operate the speaker system for about 10 seconds. In case of that the speaker system cannot be operated without displaying message in the front panel display, the front panel display lights with the brightness of the [DARK] setting.

Other Settings/Functions

Checking the sound settings and software version
Using the IR repeater function

You can check the stream 1 Press and hold SOUND FIELD on the

information, current settings remote control for more than 5 seconds.

of the sound field and voice/ The stream information appears in the front

night modes, and software

panel display.

version.

2 Press (volume) +/­ on the remote

control to display the desired checking

item.

Each time you press (volume) ­ on the remote control, the displayed item changes cyclically as follows.

Stream information Sound field Voice mode Night mode Software version
The checking item appears in the reverse order by pressing (volume) +.

When the bar speaker

1 Press and hold (BLUETOOTH) and

obstructs the remote control ­ (volume) on the bar speaker for more

sensor of the TV, the TV

than 5 seconds.

remote control may not

[IR REPEATER] appears in the front panel

work. In that case, enable

display.

the IR repeater function of the speaker system. You can control the TV with the TV remote control by

2 Press (volume) +/­ on the remote
control to display the desired setting in the
front panel display.

sending the remote signal 3 Wait until the displayed setting disappears

that the bar speaker received from the front panel display.

to the TV.

The setting is fixed.

Updating the software

Note When using the IR repeater function, install the bar speaker apart from the TV screen by 9 cm or more.

Start the software update 1 Connect the USB memory on which the

after connecting the USB

software update file is stored to the

memory on which the

UPDATE port on the bar speaker.

software update file is stored 2 Press and hold (power), (BLUETOOTH),

to the UPDATE port on the

and + (volume) on the bar speaker for

bar speaker.

more than 5 seconds.

For information about the software updates, visit the following website:

[UPDATE] appears in the front panel display and the software update starts.

· For customers in Americas https://www.sony.com/ am/support
· For customers in Europe https://www.sony.eu/

Note Before updating, make sure the following.
— The BLUETOOTH function is on.
— The subwoofer is turned on and connected to the speaker system.

support

· For customers in Asia-

Pacific, Oceania, Middle

East, and Africa

https://www.sony-asia.

com/support

Troubleshooting
Troubleshooting
If the speaker system does not work properly, handle it in the following order.
1 Search for the cause and solution of the issue
using this troubleshooting.
2 Reset the speaker system.
All the settings of the speaker system return to their initial status. For details, see “Resetting the Speaker System.”
Should any problems persist, consult your nearest Sony dealer.
Power
The speaker system does not power up. · Check that the AC power cord (mains lead) is
connected securely. · Disconnect the AC power cord (mains lead) from
the wall outlet (mains), and then reconnect after several minutes.
The speaker system is turned off automatically. · The auto standby function is working. Press and
hold (power) and (TV) on the bar speaker for more than 5 seconds to display [AUTO STANDBY] in the front panel display, then press (volume) +/­ on the remote control to display [OFF] in the front panel display.
The speaker system does not turn on even when the TV is turned on. · Set the Control for HDMI function to on. Press
and hold VOICE on the remote control for more than 5 seconds to display [CONTROL FOR HDMI] in the front panel display, then press (volume) +/­ on the remote control to display [ON] in the front panel display. The TV must support the Control for HDMI function. For details, refer to the operating instructions of your TV. · Check the speaker settings of the TV. The speaker system power syncs with the speaker settings of the TV. For details, refer to the operating instructions of your TV. · Depending on the TV, if the sound was output from the speakers of the TV the previous time, the speaker system may not turn on by interlocking with the TV power even when the TV is turned on.
The speaker system turns off when the TV is turned off. · Check the setting of the Control for HDMI
function by pressing and holding VOICE on the remote control for more than 5 seconds to display [CONTROL FOR HDMI] in the front panel display. To change the setting, press (volume) +/­ on the remote control. When the Control for HDMI function is set to on and the input of the speaker system is the TV input, the speaker system turns off automatically when you turn off the TV.
The speaker system does not turn off even when the TV is turned off. · Check the setting of the Control for HDMI
function by pressing and holding VOICE on the remote control for more than 5 seconds to display [CONTROL FOR HDMI] in the front panel display. To change the setting, press (volume) +/­ on the remote control. When you turn off the TV, the speaker system turns off automatically only if the input of the speaker system is the TV input. The TV must support the Control for HDMI function. For details, refer to the operating instructions of your TV.
Picture
There is no picture or the picture is not output correctly. · When there is no picture while TV input is
selected, select the TV channel that you want using the TV remote control.
Sound
No TV sound is output from the speaker system. · Check the type and connection of the HDMI
cable or optical digital cable that is connected to the speaker system and the TV (refer to the supplied Startup Guide). · Disconnect the cables that are connected between the TV and the speaker system, then connect them firmly again. Disconnect the AC power cords of the TV and the speaker system from the AC outlets (mains), then connect them again. · When the speaker system and TV are connected with an HDMI cable only, check the following. — The HDMI jack of the connected TV is labeled
with “ARC.” — The Control for HDMI function of the TV is set
to on. — On the speaker system, the Control for HDMI
function is set to on. Press and hold VOICE on the remote control for more than 5 seconds to display [CONTROL FOR HDMI] in the front panel display, then press (volume) +/­ on the remote control to display [ON] in the front panel display. · If your TV is not compatible with ARC, connect the optical digital cable (supplied) (refer to the supplied Startup Guide). If the TV is not compatible with ARC, TV sound will not be output from the speaker system even if the speaker system is connected to the TV’s HDMI IN jack. · Select the TV input by pressing INPUT. · Increase the volume on the TV or cancel muting. · Depending on the order in which you turn on the TV and the speaker system, the speaker system may be muted. If this happens, turn on the TV first, then the speaker system. · Set the speakers setting of the TV (BRAVIA) to Audio System. Refer to the operating instructions of your TV regarding how to set the TV. · Check the sound output of the TV. Refer to the operating instructions of the TV for the TV settings. · The speaker system supports the Dolby Digital and PCM audio formats. When you playback an unsupported format, set the digital audio out setting of the TV (BRAVIA) to “PCM.” For details, refer to the operating instructions of your TV.
The sound is output from both the speaker system and the TV. · Change the audio output setting of the TV so
that the TV sound is output from the external speaker. · Set the TV volume to minimum.
The output sound of the speaker system is not the same level as that of the TV even though the values of the volume level on the speaker system and TV are set to the same value. · If the Control for HDMI function is set to on, the
value of the volume level on the speaker system may appear on your TV as the TV volume. The output sound levels of the speaker system and TV differ even though the values of the volume level on the speaker system and TV are set to the same value. The output sound levels of the speaker system and TV differ depending on the sound processing characteristics of each, and it is not a malfunction.
The surround effect cannot be obtained. · Depending on the input signal and the sound
field setting, surround sound processing may not work effectively. The surround effect may be subtle, depending on the program or disc. · To play multi channel audio, check the digital audio output setting on the device connected to the speaker system. For details, refer to the operating instructions of the connected device.
Subwoofer
No sound or only very low-level sound is heard from the subwoofer. · Press BASS + on the remote control to increase

the subwoofer volume. · Make sure that the power indicator on the
subwoofer is lit in green or amber. · If the power indicator on the subwoofer does
not light, try the following. — Make sure the AC power cord (mains lead) of
the subwoofer is connected properly. — Press (power) of the subwoofer to turn on
the power. · If the power indicator on the subwoofer lights in
red, try the following. — Move the subwoofer to a location near the bar
speaker so that the power indicator on the subwoofer lights in green or amber. — Follow the steps in “Connecting the Subwoofer Manually.” · If the power indicator on the subwoofer flashes in red, press (power) of the subwoofer to turn off the power and check whether the ventilation holes of the subwoofer is blocked or not. · If the input sources contain very little bass sound components (i.e., a TV broadcast), the sound from the subwoofer may be difficult to hear. Play the built-in demonstration music by following the steps below and check that the sound is output from the subwoofer. Press and hold (TV) on the bar speaker for 5 seconds. The built-in demonstration music is played. Press (TV) again. The built-in demonstration music is canceled and the speaker system returns to TV input. · Set the night mode to off by pressing NIGHT.
BASS +/­ does not work and [NOT USE] appears in the front panel display. · BASS +/­ does not work when the subwoofer is
not connected. Check the power and connection status of the subwoofer.
Mobile Device Connection
BLUETOOTH connection cannot be completed. · Make sure that the BLUETOOTH indicator on the
bar speaker is lit. · Make sure the BLUETOOTH device to be
connected is turned on and the BLUETOOTH function is enabled. · Bring the BLUETOOTH device close to the bar speaker. · Pair the speaker system and the BLUETOOTH device again. You may need to cancel the pairing with the speaker system using your BLUETOOTH device first. · If the BLUETOOTH function is set to off, set it to on. To change the BLUETOOTH function setting, press and hold (power) and (BLUETOOTH) on the bar speaker for more than 5 seconds (the changed setting appears in the front panel display).
Pairing cannot be achieved. · Bring the BLUETOOTH device close to the bar
speaker. · Make sure the speaker system is not receiving
interference from a wireless LAN device, other 2.4 GHz wireless devices, or a microwave oven. If a device that generates electromagnetic radiation is nearby, move the device away from the speaker system. · Pairing may not be possible if other BLUETOOTH devices are present around the speaker system. In this case, turn off the other BLUETOOTH devices.
Sound of the connected BLUETOOTH mobile device is not output from the speaker system. · Make sure that the BLUETOOTH indicator on the
bar speaker is lit. · Bring the BLUETOOTH device close to the bar
speaker. · If a device that generates electromagnetic
radiation, such as a wireless LAN device, other BLUETOOTH devices, or a microwave oven is nearby, move the device away from the speaker system. · Remove any obstacle between the bar speaker and the BLUETOOTH device or move the bar speaker away from the obstacle. · If the bar speaker is installed under the TV, move the bar speaker away from the TV. · Reposition the connected BLUETOOTH device. · Switch the wireless LAN frequency of any nearby wireless LAN router or PC to 5 GHz range. · Increase the volume on the connected BLUETOOTH device.
The sound is not in sync with the image. · When you are watching movies, you may hear
the sound with a slight delay from the image.
Remote Control
The remote control of the speaker system does not function. · Point the remote control at the remote control
sensor on the bar speaker. · Remove any obstacles in the path between the
remote control and the speaker system. · Replace both batteries in the remote control
with new ones, if they are weak. · Make sure you are pressing the correct button
on the remote control.
The TV remote control does not work. · Install the bar speaker so that it does not
obstruct the remote control sensor of the TV. · This problem might be solved by enabling the IR
repeater function. Press and hold (BLUETOOTH) and ­ (volume) on the bar
speaker for more than 5 seconds to display [IR REPEATER] in the front panel display, then press (volume) +/­ on the remote control to display [ON] in the front panel display.
Others
The Control for HDMI function does not work properly. · Check the connection with the speaker system
(refer to the supplied Startup Guide). · Enable the Control for HDMI function on the TV.
For details, refer to the operating instructions of your TV. · Wait a while, and then try again. If you unplug the speaker system, it will take a while before operations can be made. Wait for 15 seconds or longer, and then try again. · Make sure the TV connected to the speaker system supports the Control for HDMI function. · The type and number of devices that can be controlled by the Control for HDMI function is restricted by the HDMI CEC standard as follows: — Recording devices (Blu-ray Disc recorder, DVD
recorder, etc.): up to 3 devices — Playback devices (Blu-ray Disc player, DVD
player, etc.): up to 3 devices — Tuner-related devices: up to 4 devices — Audio system (receiver/headphone): up to 1
device (used by the speaker system)
[PROTECT] is scrolled in the front panel display, then the speaker system is turned off after 5 seconds. · The protection feature is activated. Disconnect
the AC power cord (mains lead) and make sure that the ventilations of the bar speaker are not covered and turn on the speaker system after a while.
Sensors of the TV do not work properly. · The bar speaker may block some sensors (such
as the brightness sensor), the remote control sensor of your TV or the emitter for 3D glasses (infrared transmission) of a 3D TV that supports the infrared 3D glass system, or wireless communication. Move the bar speaker away from the TV within a range that allows those parts to operate properly. For the locations of the sensors and remote control receiver, refer to the operating instructions of the TV.
The speaker system does not work properly. · The speaker system may be in demo mode. To
cancel demo mode, reset the speaker system. Press and hold (power) and ­ (volume) on the bar speaker for more than 5 seconds.

The following message appears.
Please select the desired TV channels with the TV’s remote control.
HT-SD40
* This screen is an example for English.
· Select the TV program by using the TV remote control.
Resetting the Speaker System
If the speaker system does not operate properly, reset the speaker system as follows.
1 Press and hold (power) and ­ (volume) on
the bar speaker for more than 5 seconds. [RESET] appears in the front panel display, and the settings return to their initial status.
2 Disconnect the AC power cord (mains lead). 3 Connect the AC power cord (mains lead), then
press (power) to turn on the speaker system.

Specifications
Bar Speaker (SA-SD40)
Amplifier section POWER OUTPUT (rated)
Front L + Front R: 60 W + 60 W (at 4 ohms, 1 kHz, 1% THD) POWER OUTPUT (reference)
Front L/Front R speaker: 100 W (per channel at 4 ohms, 1 kHz) Input
TV IN (OPTICAL) Output
HDMI OUT (TV (ARC))
HDMI section Connector
Type A (19 pin)
USB section UPDATE port:
Type A (For software update only)
BLUETOOTH section Communication system
BLUETOOTH Specification version 5.0 Output
BLUETOOTH Specification Power Class 1 Maximum communication range
Line of sight approx. 25 m1) Maximum number of devices to be registered
9 devices Frequency band
2.4 GHz band (2.4000 GHz – 2.4835 GHz) Maximum output power
< 14 dBm Modulation method
FHSS (Freq Hopping Spread Spectrum) Compatible BLUETOOTH profiles2)
A2DP (Advanced Audio Distribution Profile) AVRCP (Audio Video Remote Control Profile) Supported Codec3) SBC4) Transmission range (A2DP) 20 Hz – 20,000 Hz (Sampling frequency 32 kHz, 44.1 kHz, 48 kHz)
1) The actual range will vary depending on factors such as obstacles between devices, magnetic fields around a microwave oven, static electricity, cordless phone use, reception sensitivity, the operating system, software applications, etc.
2) BLUETOOTH standard profiles indicate the purpose of BLUETOOTH communication between devices.
3) Codec: Audio signal compression and conversion format
4) Abbreviation for Subband Codec
Front L/Front R speaker section Speaker system
2 speaker system Speaker
52 mm × 100 mm cone type, 4 ohms
General Power requirements
220 V – 240 V AC, 50 Hz/60 Hz Power consumption
On: 35 W Standby mode: 0.5 W or less (Power Saving mode) (When Control for HDMI function and BLUETOOTH standby mode are set to off) Standby mode: 2 W or less* (When Control for HDMI function and BLUETOOTH standby mode are set to on)
* The speaker system will automatically enter Power Saving mode when there is no HDMI connection and no BLUETOOTH pairing history.
Dimensions* (approx.) (w/h/d) 900 mm × 64 mm × 88 mm
* Not Including projection portion Mass (approx.)
2.4 kg
Subwoofer (SA-WSD40)
POWER OUTPUT (reference) 130 W (at 4 ohms, 100 Hz)
Speaker system Bass reflex
Speaker 160 mm cone type, 4 ohms
Power requirements 220 V – 240 V AC, 50 Hz/60 Hz
Power consumption On: 20 W Standby mode: 0.5 W or less
Dimensions* (approx.) (w/h/d) 192 mm × 387 mm × 400 mm
* Not Including projection portion Mass (approx.)
7.3 kg
Wireless Transmitter/Receiver Section
Frequency band 2.4 GHz (2.404 GHz – 2.476 GHz)
Maximum output power < 10 dBm
Modulation method GFSK
Supplied Accessories
· Remote control (1) · R03 (size AAA) battery (2) · WALL MOUNT TEMPLATE (1) · Optical digital cable (1) · AC power cord (mains lead) (2) · Startup Guide · Operating Instructions (this document)
Design and specifications are subject to change without notice.

Copyrights and Trademarks
This speaker system incorporates Dolby* Digital.
* Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
The BLUETOOTH® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Sony Group Corporation is under license. Other trademarks and trade names are those of their respective owners.
The terms HDMITM, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
“BRAVIA” logo is a trademark of Sony Corporation.
All other trademarks are trademarks of their respective owners.

Supported Input Audio Formats (HDMI OUT (TV (ARC)) or TV IN (OPTICAL))
Audio formats supported by this speaker system are as follows. · Dolby Digital · Linear PCM 2ch

On BLUETOOTH Communication
· BLUETOOTH devices should be used within approximately 10 meters (33 feet) (unobstructed distance) of each other. The effective communication range may become shorter under the following conditions.
— When a person, metal object, wall or other obstruction is between the devices with a BLUETOOTH connection
— Locations where a wireless LAN is installed
— Around microwave ovens that are in use
— Locations where other electromagnetic waves occur
· BLUETOOTH devices and wireless LAN (IEEE 802.11b/g/n) use the same frequency band (2.4 GHz). When using your BLUETOOTH device near a device with wireless LAN capability, electromagnetic interference may occur. This could result in lower data transfer rates, noise, or inability to connect. If this happens, try the following remedies:
— Use this speaker system at least 10 meters (33 feet) away from the wireless LAN device.
— Turn off the power to the wireless LAN device when using your BLUETOOTH device within 10 meters (33 feet).
— Install this speaker system and BLUETOOTH device as closer to each other as possible.
· The radio waves broadcast by this speaker system may interfere with the operation of some medical devices. Since this interference may result in malfunction, always turn off the power on this speaker system and BLUETOOTH device in the following locations:
— In hospitals, on trains, in airplanes, at gas stations, and any place where flammable gasses may be present
— Near automatic doors or fire alarms
· This speaker system supports security functions that comply with the BLUETOOTH specification to ensure secure connection during communication using BLUETOOTH technology. However, this security may be insufficient depending on the setting contents and other factors, so always be careful when performing communication using BLUETOOTH technology.
· Sony cannot be held liable in any way for damages or other loss resulting from information leaks during communication using BLUETOOTH technology.
· BLUETOOTH communication is not necessarily guaranteed with all BLUETOOTH devices that have the same profile as this speaker system.
· BLUETOOTH devices connected with this speaker system must comply with the BLUETOOTH specification prescribed by the Bluetooth SIG, Inc., and must be certified to comply. However, even when a device complies with the BLUETOOTH specification, there may be cases where the characteristics or specifications of the BLUETOOTH device make it impossible to connect, or may result in different control methods, display or operation.
· Noise may occur or the audio may cut off depending on the BLUETOOTH device connected with this speaker system, the communications environment, or surrounding conditions.
If you have any questions or problems concerning your speaker system, please consult your nearest Sony dealer.

©2022 Sony Corporation Printed in China