1byone H004 Turntable Hi-Fi System with Speakers Instruction Manual

1byone H004 Turntable Hi-Fi System with Speakers

Introduction

Thank you for purchasing 1byone Turntable Hi-Fi System with Speakers. This instruction manual contains important information about safety, usage and disposal. Use the product as described and keep this manual for future reference. If you sell this turntable or pass it on, also give this manual to the new owner.

Safety Instructions

Read and understand this entire manual before using this product. Keep these instructions for future reference.

1.   Do not use the turntable near water.
2.  Only connect the turntable to a power outlet type as indicated on the marking label or in the “Specifications” section of this instruction manual.
3.  The turntable has a polarized plug (one pin is wider than the other). To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet in only one orientation. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way.
4.  Protect the power cord from being walked on or pinched, particularly at the power plug, at the point of connection between the plug and outlet and at the point of connection between the power cable and speaker.
5.  Do not overload wall outlets or extension cords as this will be a fire hazard and may cause electric shock.
6.  Never push objects of any kind into the turntable through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
7.  Do not attempt to service the turntable yourself as opening or removing body panels may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
8.  Changes or modifications to the turntable not expressly approved by the party responsible for compliance could void the user’s authority to operate the product.
9.  Do not use attachments not recommended by the manufacturer as they may cause hazards.
10.  Only place on a flat, sturdy table or use with the cart, stand, tripod or bracket as specified by the manufacturer or sold with the turntable. When a cart is used, use caution when moving the cart/turntable combination to avoid injury from tip-over.
11.  Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating. Do not block or cover these openings.
12.  Unplug the product during lightning storms or when unused for long periods of time.

COMPLIANCE WITH FCC REGULATIONS

This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:

1.  This device may not cause harmful interference, and
2.  This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Cancer and Reproductive Harm – HYPERLINK “http://www. P65Warnings.ca.gov.” For more information go to HYPERLINK “http://www.1byonebros.com/Compliance/Prop65”

Product Description

1.  Motor Pulley
2.  Drive Belt
3.  Turntable Spindle
4.  Turntable Sub-platter
5.  Turntable Platter
6.  Lid Hinge
7.  Anti-skating Weight
8.  Counterweight
9.  Anti-skating Stick
10.  Tonearm Rest
11.  Tonearm Lift Lever
12.  Tonearm Clip
13.  Volume Control
14.  Indicator
15.  33/45RPM Selector
16.  Play/Stop Button
17.  Mode Button
18.  Stylus Cartridge
19.  Ground Connector
20.  Phono & Line Out Jacks
21.  Phono & Line Out Switch
22.  USB Port for PC Link
23.  Power Cord Jack
24.  External Speaker Jacks
25.  Power Switch
26.  Speaker Jack –
27.  Speaker Jack +

Included Items

Before installing the turntable, check the package contents to ensure all parts below are included and free of visible damage. Please retain the original packaging materials for exchange or return purposes.

• 1 x Turntable Unit
• 2 x Speakers
• 1 x Turntable Lid
• 1 x Slip Mat
• 1 x Turntable Platter
• 1 x Tonearm Counterweight 1 x Anti-skating Weight
• 1 x 45 RPM adapter
• 1 x Drive Belt
• 1 x Sub-platter
• 1 x Belt Hook
• 1 x Power Adapter
• 1 x USB Cable for PC Link
• 2 x Audio Cables for Speakers 1 x Cartridge Adjustment Card 1 x Instruction Manual

Installing the Turntable

•  Mount the product on a level surface.
•  To avoid the effects of vibrations and acoustic pressure, do not mount the product next to such items as speakers.
•  The product may pick up radio static if placed next to a radio. Therefore, try to keep the product away from radios.
•  If the product is near equipment (cell phone, etc.) that emits strong radio waves, noise may occur.

Installing the Lid

Insert the hinge pockets of the lid onto the hinges of the turntable.

Turntable Platter and Belt Setup

1.  Remove the protective packaging and ensure the turntable is placed on a sturdy and level surface.
2.  Insert the sub-platter into the turntable.
3.  Loop the drive belt around the sub-platter and motor pulley (brass-colored).
4.  Carefully place the main platter onto the sub-platter (Figure 1).

Rotating the Platter

1.  Using your hands, slowly rotate the platter ten times in the direction of the arrow (Figure 1). This step is for resetting the auto mechanism, getting rid of any twists in the belt and making sure the belt rides smoothly along the drive rim on the underside of the platter. Place the slip mat on top of the platter. Make sure the 1byone logo on the mat is facing up (Figure 2).

Cartridge Tracking Force Adjustment

The Counterweight supplied is suitable for cartridges weighing between 3.0-6.0g.

1.  Gently push and turn the Counterweight onto rear of the tonearm (with the dial facing toward front of the turntable).
2.  Pull the protector straight forward to remove it. NOTE: Applying a downward force may cause the stylus to come off the body. Only low volume is output if the stylus has come off, or is about to come off, so refer to “Replacing the stylus” to reattach the stylus correctly.
3. Remove the tie-wrap and unlock the tonearm.
4.  Lower the tonearm lift lever and position the cartridge in the tonearm rest and platter.
5. Carefully rotate the Counterweight until the tonearm achieves a neutral balance. The tonearm should return to this balanced position adjustment must be done carefully.
6. Once the tonearm is correctly balanced, return the tonearm to its rest. Hold the Counterweight without moving it, and gently rotate the tracking force dial until the zero is in line with black center line on the rear of the tonearm. Check to make sure the tonearm is still neutrally balanced.
7. Rotate the counterweight counter clockwise (as seen from the front) to adjust the tracking force according to the cartridge manufacturer’s recommendations.

Anti-skating Force Adjustment

The anti-skating force must be adjusted corresponding to the tracking force as follows

1.  Slip the loop of the anti-skating weight’s thread over the 3rd groove of the stick to set the correct anti-skating force for the factory-installed cartridge.
2.  Feed the thread through the loop of the wire hanger

Connection to Speakers

1.  Connection to the Included Speakers This turntable includes a built-in preamp and comes supplied with Hi-Fi speakers. Connect the speakers using the included audio cable (dark cable to black cable clamp and light cable to red cable clamp).
2.  Connection to External Speaker with the RCA Audio Cable If you wish to use your own amplifier or speakers, please follow the instructions below:

Setting pre-amplifier selector switch
This product has a built-in phono equalizer function. You can use the product even if you do not have a phono amplifier or connectable equipment with a built-in phono amplifier.

Use the pre-amplifier selector switch to set the output, as shown below.
When connecting via the included speakers, using the pre-amplifier selector switch is not necessary

Connecting the device
Align the settings for the pre-amplifier selector switch and connect the RCA audio cable to an input jack that is compatible with the connectable equipment you are using (amplifier, active speakers, etc.).

• The RCA audio cable’s red jack is for the right (R) channel, and the white jack is for the left (L) channel

Main Power Connection

1.  Insert the DC plug of the AC adapter cord into the DC INPUT Jack at the back of the turntable.
2.  Plug the AC adapter into a normal power outlet.
   NOTE: Do not plug the AC power adapter into a power outlet before all turntable assembly is completed. Before turning on turntable power, recheck all connections to make sure they are correct and secure. Always turn off the turntable before connecting or disconnecting from power.

Power Management Function
The turntable will automatically go into standby mode after 15 minutes of inactivity.
To resume operation, press and hold the Mode button for 3 seconds.

Playing a Record

1.  Before playing a record
   1.  Pull the protector straight forward to remove it.
   2.  Place the record on the felt mat so that the center hole aligns with the spindle.
      If playing a 45 RPM record with a large center hole, attach the 45 RPM adapter
2. Turntable Operation
3. Lower the volume of the amplifier, speakers, etc. sufficiently.
   1.  Connect the included power adapter to the turntable and slide the Power Switch to the “ON” position.
   2.  Remove the stylus protector from the stylus.
   3.  Press the MODE button to choose turntable mode. Red indicator light indicates Turntable mode and blue indicator light indicates Bluetooth mode.
   4.  Place the record on the slip mat. If using 45RPM records, put the 45RPM adapter on the center spindle before placing the record on the platter.
   5.  Press the 33 or 45 RPM speed button according to the type of record.
   6.  Press the Play/Stop button. The platter will start spinning. 45RPM Adapter
   7.  Unlock the tonearm clip and set the tonearm lift lever to the up position.
   8.  Position the tonearm over the desired location (groove) on the record.
   9.  Carefully lower the tonearm on the record.
   10. Turn up the volume of the turntable as needed.
   11.  When you are finished playing the record, raise the tonearm, return it to rest on the arm clip and press the Play/Stop button to stop.

Bluetooth Operation

1.  Connect the included power adapter to the turntable and slide the Power Switch to the “ON” position.
2.  Press the MODE button to choose Bluetooth mode. Red indicator light indicates Turntable mode and blue indicator light indicates Bluetooth mode. You will hear an activation sound from the turntable.
3.  Turn on the Bluetooth feature of your media device and search for and select “1byone BS017” to pair the media device and turntable.
4. Once your media device is successfully paired with the turntable, the turntable will play a short confirmation sound.
5.  Play and stream music from your media device to the turntable.
   Note: Bluetooth version: 5.0

Recording the Vinyl to Your Computer
Please follow the below steps to set up Audacity to record from the USB audio device. For more details, please refer to the BRIEF INTRODUCTION OF AUDACITY at https:// manual.audacityteam.org/man/recording_with_usb_turntables.html

1.  Download the Audacity software and complete installation
   1. Ensure your Audacity software is up to date. You can download the current version from http://www.audacityteam.org/download/
   2.  Follow the instructions to complete installation.
2.  Set up Audacity to record from the USB audio device
   1.  Connect the USB device
      Use the supplied USB cable to connect your turntable and your computer. No extra driver is required.

1.  By the system clock, right-click over the Speaker icon select Sounds then the Recording tab, and then click on the USB device in the list and click Properties. Click the Advanced tab set your required bit rate and sample rate from the Default Format dropdown (normally “2 channel 16-bit 44100 Hz”).
2. On the Advanced tab, in the “Default Format” section, make sure the dropdown menu is set to “2 channel 16-bit 44100 Hz”. For a more detailed walk-through of the above steps for Windows (or if that does not work for your version of Windows), see Windows: accessing the Windows

1.  From Apple Menu > System Preferences select “Sound” and click on the Input tab
2.  Select “USB Audio CODEC” or similar as the input device and verify the Recording Meter shows input.
3.  If the recording meter in the Sound preferences panel does not show input:
   1.  From the Finder, select Go > Utilities and open Audio MIDI Setup.
   2.  If the Audio Devices window is not visible, select Window > Show Audio Devices.
   3.  Select your USB input device in the list in the left pane of the Audio Devices window.
   4.  Set the Format to “44100.0 Hz” and “2ch-16bit”.

Set the Audacity Project Rate in Selection Toolbar at the bottom left of the Audacity screen to 44100 Hz:

• Use Device Toolbar to set the recording and playback devices and to set the recording channels to “2 (Stereo) Recording Channels”, as in the below example on Windows 10:
•  The Recording Device is set to the USB device (in this case the device name, but often called or including the phrase “USB Audio CODEC”).
•  Recording Channels is set to stereo.
•  The Playback Device is set to the named speakers of the built-in computer sound device.
•  These settings can also be changed in Devices Preferences.
• Windows calls most USB external devices “microphones”. Some higher-end USB recording interfaces may appear as their explicit manufacturer’s name.

Software Playthrough

Monitoring

•  Turn monitoring on by clicking once on the microphone icon in the Recording
  Meter.
•  In Mixer Toolbar, turn up the left-hand playback volume slider (by the speaker icon).
•  The right-hand recording volume slider (by the microphone icon) can often be used to vary the loudness of the recording, but it may not function with all turntables.
• If it does not, try adjusting the output level on the turntable (often, there is a gain control under the chassis).
• Alternatively, you may be able to adjust the input level on Windows and Linux only, usually by looking for the speaker icon by the system clock. On Windows, right-click over the speaker icon > “Recording Devices”. Then right-click over USB
• Audio Codec, choose “Properties” and click the Levels tab.
• Try to aim for a maximum peak of around –6 dB, which corresponds to around 0.5 on the waveform. You can always boost the level later with Effect > Amplify… or Effect > Normalize… after you have completed editing.

Recording

Recording, editing and exporting

• make and edit your recording
• export it to an audio file
• import it to iTunes or Windows Media Player
• burn it to CD

• Basic Recording, Editing and Exporting : https://manual.audacityteam.org/man/basic_recording_editing_and_exporting.html
• Tutorial – Copying tapes, LPs or MiniDiscs to CD : https://manual.audacityteam.org/man/tutorial_copying_tapes_lps_or_minidiscs_to_cd.html

Care

Turntable Body

• When the turntable body is dirty or dusty, first disconnect the AC adapter, and then wipe off the dirt and dust with a soft, dry cloth.
• Do not use benzenes, thinners, etc.
• When storing the product for a long time, disconnect the AC adapter from the outlet and wrap the product in plastic; do not allow it to become damp; the drive belt should be removed to prevent unequal stretching.

Stylus Tip

• If dirt and grime are stuck to the stylus tip, clean it with a commercially sold brush.
• We recommend using a stylus cleaner (not included) if the stylus tip is considerably dirty. Clean the stylus tip by moving the brush from the rear to the front of the stylus tip.

Replacing the Stylus

It’s suggested to replace the stylus after 400 hours of use.

Removing the Stylus

• In addition to the deterioration of sound quality, records may also be damaged as the cartridge’s stylus tip wears down.
• Be sure to disconnect the product’s AC adapter from the outlet.
• When replacing the stylus, hold the headshell and the cartridge body tightly. Rotate the front of the stylus in a forward and down motion.

Installing a New Replacement Stylus

1.  Mount the new replacement stylus to the cartridge.
2.  Lift the stylus up until you hear a click.
3.  Make sure there is no gap between the headshell and the cartridge.

Replacing the Belt

• The belt is a consumable part. Replace the belt if the speed of playback slows down or irregular rotation occurs. As a rule of thumb, we suggest replacing the belt once a year.
• Before replacing the belt, be sure to disconnect the product’s AC adapter from the outlet.

1.  Remove the slip mat.
2.  Remove the main platter, and then remove the old belt.
3.  Loop the new belt around the sub-platter and motor pulley.
4.  Place the main platter back onto the sub-platter
5.  Using your hands, slowly rotate the platter ten times by hand in the direction of the arrow.

When the Turntable is Moved
Using the product’s original packing materials, wrap the turntable in the reverse order from when you unwrapped it. If you do not have the packaging materials, take the following measures:

• After disconnecting the AC adapter from the outlet, remove the felt mat and platter, and then wrap them so that they do not get damaged.
• Attach the protector to the cartridge.
• Use a string or something similar to tie the tonearm to the rest so that it does not move.
• Wrap the turntable body with paper or a soft cloth so that it does not get damaged

Troubleshooting

Specifications

Turntable

Stylus

Speaker

Disposal

• Disposal of the Product
• Under no circumstances should you dispose of the product in normal domestic waste.
• This product is subject to the provisions of European Directive 2012/19/EU. Dispose of the product via an approved disposal company or your municipal waste facility. Please observe currently applicable regulations.
• Please contact your waste disposal center if you need any further information. This product’s packaging is made from environmentally friendly material and can be disposed of at your local recycling plant