LG SN11R Sound Bar Owner’s Manual

SIMPLE MANUAL
LG Wi-Fi
Sound Bar

Front Panel

(Standby) · · · · · · · · · · · ·Switches the unit ON or OFF.
F (Function) · · · · · · · · · · · · · · · · · · · · · · · · · ·Selects function.
-/+ (Volume) · · · · · · · · · · · · · · · · · · · · · · Adjusts the volume.
(Wi-Fi) · · · · · · · · · · · · · · · · · · · ·Selects Wi-Fi function.

Reset the Unit
Press and hold the / on the unit until you hear the beep sound once.

Rear Panel

USB (Service only) · · · · · · · · · ·S/W download connector.
OPTICAL IN · · · · · · · · · · · · ·Connect to an optical device.
HDMI OUT (TV eARC/ARC) · · · · · · · Connect to a TV.
HDMI IN (1) / HDMI IN (2) · · · · · · · · · · · · · · · · · · · ·
Connect to device with HDMI OUT.

Make sure to properly align and connect the optical cable; improper alignment may cause damage to the jack.

Subwoofer Connection

Place the wireless subwoofer near the soundbar and follow the steps below.

  1. Connect the power cord of the soundbar and the wireless subwoofer to the outlet.
  2.  Turn on the soundbar.
    • The soundbar and wireless subwoofer will be automatically connected. The subwoofer’s green LED turns on.

Manually Subwoofer Connection
If the subwoofer does not make a sound, try to connect manually.

  1. Press Pairing on the rear of the wireless subwoofer.
    • The green LED on the rear of the wireless subwoofer blinks quickly.
    (If the green LED does not blink, press and hold the Pairing.)
  2. Turn on the soundbar.
    • Pairing is completed. The green LED on the rear of the wireless subwoofer turns on.

Keep the soundbar and the subwoofer away from the device (ex. wireless router, microwave oven, etc.) for over 1 m to prevent wireless interference.

TV Connection

Connect the soundbar and TV using Optical (A ) or HDMI ARC (B).
A Optical Connection

  1.  Connect the soundbar to the TV using an Optical cable.
  2. Set up [External Speaker (Optical)] on your TV setting menu.

B HDMI (TV eARC/ARC) Connection

  1. Connect the soundbar to the TV using an HDMI cable.
  2.  Set up [External Speaker (HDMI ARC)] on your TV setting menu.

  •  The HDMI connection is unavailable if your TV does not support HDMI ARC.
  • If this unit is connected by OPTICAL and ARC at the same time, the ARC signal has a higher priority.

Additional Device Connection

  1.  Connect to the external device as follow.
  2. Set the input source by pressing F repeatedly.

Network Connection

  1. Check network condition. A router connected to the network should be installed.
  2. Connect your smart device to your home network.
  3. Connect the soundbar to the power supply.

All devices should be connected to the same router.

Step.1 Install the “Google Home” App
Download the Google Home App from the Google Play or App Store.
Step.2 Set up the Wi-Fi connection with the app

  1.  Connect your smart device to the Wi-Fi network that you’ll use for your unit.
    In the case of iOS devices, it should be turned on Bluetooth setting on your smart device.
  2. Launch the “Google Home” app.
  3. Follow the steps for Wi-Fi connection on the app.
    • When the unit is properly connected to Wi-Fi, “CONNECTED” will appear on the display window with sound.
  • When connecting to Wi-Fi, this app may request to create a Google Account. You will need a Google account to use this app.
  •  “Google Home” app is provided by Google. It might be revised by a change of Google Policy.

Remote control

Replacement of Battery

SOUND EFFECT: Selects a sound effect mode.
– TV remote: Long press SOUND EFFECT and press it again to use the TV remote control.
: Turns on or off the Night-time mode.
: Displays the information of a file, an input source, a connected Bluetooth device name, or an application name.
– Auto Power ON/OFF: Long press and press it again.
: Adjusts the sound level of each speaker.
– Surround sound: Long press and press it again.
*: This button is not available.

Additional

Download LG Sound Bar Application
You can manage the speaker settings and control the speaker by using “LG Sound Bar”.
Download “LG Sound Bar” on the App Store or
Google Play Store.

AI Room calibration
AI Room Calibration is a sound tuning tool, which adjusts the audio settings of the Sound Bar based on the room acoustics and environment. To access the AI Room  Calibration it is necessary to install the “LG Sound Bar” app. On the [Sound Setting] menu, choose [AI Room Calibration].

Additional Information

Specification

Power requirements Refer to the main label.
Power consumption Refer to the main label.
Networked standby: 6.5 W (If all network ports are activated.)
Dimensions (W x H x D) Approx.
1443.0 mm x 63.0 mm x
146.0 mm (with foot)
Amplifier (Total RMS Output power) 770 W RMS

Design and specifications are subject to change without notice.

Rear Surround sound
Wireless Rear Speakers Kit included for real surround sound. (SPN11M-SL / SPN11M-SR)

To enjoy content containing Dolby Atmos® and DTS: X®, the connected device and content must support Dolby Atmos® and DTS: X®.
How to disconnect the wireless network connection or the wireless device
Turn off the unit by pressing the power button for more than 3 seconds.

OPEN-SOURCE SOFTWARE NOTICE INFORMATION

To obtain the source code under GPL, LGPL, MPL, and other open-source licenses, that is contained in this product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers, and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon email request to .
This offer is valid for a period of three years after our last shipment of this product. This offer is valid to anyone in receipt of this information.
Declaration of Conformity

Hereby, LG Electronics declares that the radio equipment type Wi-Fi SOUNDBAR is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.lg.com/global/support/cedoc/cedoc#
For the consideration of the user, this device should be installed and operated with a minimum distance of 20 cm between the device and the body.

Please read this manual carefully before operating your set and retain it for future reference.
To view the instructions for advanced features, visit http://www.lg.com and then download Owner’s Manual. Some of the content in this manual may differ from your unit.
MODEL
SN11R

www.lg.com
Copyright © 2021 LG Electronics Inc. All Rights Reserved.

SIMPLE MANUAL
Wireless Rear Speakers Kit

Wireless Rear speakers connection

  1. Connect the power cord of the wireless rear speakers to the outlet.
  2.  Turn on the main unit: The soundbar and wireless rear speakers will be automatically connected.
    The green LED on the wireless rear speakers turns on.

Manually pairing wireless rear speakers
When your connection is not completed, you can see the red LED on the wireless rear speaker and the speaker does not make a sound. Try to connect manually.

  1. Press PAIRING on the rear of the wireless rear speaker.
    (If the green LED does not blink, press and hold the PAIRING.)
    • The green LED on the wireless rear speaker blinks quickly.
  2. Turn on the main unit
    • Paring is completed. The green LED on the wireless rear speaker turns on.

Set the distance between the soundbar and the wireless rear speakers as close as possible and keep them away from the device (ex. wireless router, microwave oven, etc.) over 1  m to prevent wireless interference.

Surround Sound On/Off

When you turn on the surround function, you can enjoy magnificent surround sound for all the input sound sources with rear speakers.

The initial setting for the surround function is OFF, turn the surround function ON to use it.

Surround On: Press and hold the button on the remote control for about 3 seconds and then press button repeatedly to select ON – SURROUND in the display window.
Surround Off: Press and hold the button on the remote control for about 3 seconds and then press button repeatedly to select OFF – SURROUND in the display window.

Additional Information

Specification (Each speaker)

Power requirements Refer to the main label.
Power consumption Refer to the main label.
Dimensions
(W x H x D)		 Approx.
130.0 mm x 211.5 mm x
191.2 mm (with foot)

Design and specifications are subject to change without notice.

Declaration of Conformity
Hereby, LG Electronics declares that the radio equipment type ACTIVE REAR SPEAKER is in compliance with Directive 2014/53/EU. The full text of the EU declaration of  conformity is available at the following internet address: http://www.lg.com/global/support/cedoc/cedoc#
For the consideration of the user, this device should be installed and operated with a minimum distance of 20 cm between the device and the body.

Please read this manual carefully before operating your set and retain it for future reference.
To view the instructions for advanced features, visit http://www.lg.com and then download Owner’s Manual. Some of the content in this manual may differ from your unit.
MODEL
SPN11M-SL, SPN11M-SR

    www.lg.com
Copyright © 2021 LG Electronics Inc. All Rights Reserved.