Miele EPI7684 Wireless Food Probe System User Manual

Miele EPI7684 Wireless Food Probe System

General

The wireless food probe system consists of the radio module (EPI7684), antenna system and the wireless food probe. This system enables the roasting process of the food to be monitored simple and reliably. The wireless food probe will be here not described because it is a passive device and does not matter for the installation of the system.

The wireless food probe system may be installed in the Miele domestic appliances like ovens or steam cooker (host devices)

Integration instruction
The EPI7684 and the loop antenna must be integrated under consideration of the technical data. It is not allowed to make any changes on the module or use another antenna.

Technical data EPI7684 and antenna

Interface to the control-/ power electronic of the host device

On the control-/ power electronic is a 4-pin rast 2.5 plug and on the EPI site is 8-pin rast 2.5 plug. This connection includes communication and power supply wire (13 and 3,3V DC)

Norms / Standards

FCC / IC

FCC regulation:
FCC 47 CFR
Part 15.247
Part 1.1310
Part 1.1091
IC regulation:
RSS-247, Issue 2
RSS-Gen, Issue 5
RSS-102, Issue 5

Compliance Statement and Integration

In accordance with FCC 47 CFR Part 15 and RSS-247, Issue 2, the EPI7684 (FCC ID: SSVNAEPI03; IC: 5669B-EPINA03) is listed as a Modular Transmitter Device.

Notice:
This device complies with Part 15 of the FCC Rules and contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS Standarrd(s). Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Radiofrequency radiation exposure Information:

This equipment complies with FCC radiation exposure limits set forth and Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

CAUTION:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

USERS MANUAL OF THE END PRODUCT:
The end user has to be informed that any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment. The following statements are required to be available in the user’s manual: This device complies with Part 15 of the FCC Rules and contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS Standarrd(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Radiofrequency radiation exposure Information:
This equipment complies with FCC radiation exposure limits set forth and Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following “Contains FCC ID: SSVNAEPI03; Contains IC: 5669B-EPINA03”. The following statement has to also be available on the label:
This device complies with Part 15 of the FCC Rules and contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS Standarrd(s). Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Integration

This EPI7684 Module will only be integrated on our responsibility into Miele appliances/endproducts.

The host manufacturer is responsible for additional testing to verify compliance as a composite system. When testing the host device for compliance with the Part 15 Subpart B requirements, the host manufacturer is required to show compliance with the Part 15 Subpart B while the transmitter module(s) are installed and operating. The modules should be transmitting and the evaluation should confirm that the module’s intentional emissions are compliant (i.e. fundamental and out of band emissions) with the Radio essential requirements. The host manufacturer must verify that there are no additional unintentional emissions other than what is permitted in the Part 15 Subpart B or emissions are complaint with the Radio aspect