Bosch PFS 3000-2 Paint Spray System Instruction Manual

PFS 3000-2

Safety instructions

General Power Tool Safety Warnings

WARNING
Read all safety warnings, instructions , illustrations, and specifica­ tions provided with this power tool. Failure to follow all in­structions listed below may result in electric shock, fire, and/ or serious injury.

Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cord­less) power tool.

Work area safety

• Keep the work area clean and well-lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or Power tools that create sparks that may ignite the dust or fumes.
• Keep children and bystanders away while operating a
  power tool. Distractions can cause you to lose control.

Electrical safety

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock.
• Avoid body contact with earthed or grounded sur­ faces, such as pipes, radiators, ranges, and refrigerat­ There is an increased risk of electric shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of elec­tric shock.
• Do not abuse the cord. Never use the cord for carry­ ing, pulling, or unplugging the power tool. Keep cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric
• When operating a power tool outdoors, use an exten­ sion cord suitable for outdoor use. Use of a cord su it-able for outdoor use reduces the risk of electric shock.
• If operating a power tool in a damp location is un­ avoidable, use a residual current device (RCD) protec­ ted supply. The use of an RCD reduces the risk of electric

Personal safety

• Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inatten­tion while operating power tools may result in serious per­sonal injury.
• Use personal protective equipment. Always wear eye Protective equipment such as a dust mask, non-skid safety shoes, a hard hat or hearing protection used for appropriate conditions will reduce personal in­juries.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to a power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or en­ergising power tools that have the switch on invites acci­
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal in­
• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jew­ Keep your hair and clothing away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
• If devices are provided for the connection of dust ex­ traction and collection facilities, ensure these are con­ nected and properly used. The use of dust collection can re­duce dust-related hazards.
• Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe in­jury within a fraction of a second.

Power tool use and care

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was de­
• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/or re­ move the battery pack, if detachable, from the power tool before making any adjustments, changing ac­ cessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool
• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
• Maintain power tools and accessories. Check for mis­ alignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly main­tained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into ac­ count the working conditions and the work to be per­ Use of the power tool for operations different from those intended could result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean, and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Service

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Safety instructions for fine spray systems

• Keep your work area clean, well lit, and free of paint or solvent containers, clothes, and other flammable mater­ There is a risk of spontaneous combustion. Ensure that you have access to functioning fire extinguishers or extinguishing equipment at all times.
• Ensure that the spray area is well ventilated and that there is sufficient fresh air circulating in the whole area. Evaporating flammable solvents create an explosive
• Do not spray or clean with materials with a flash point lower than 55 °C. Use water-based materials, non-volatile hydrocarbons, or similar materials. Volatile
  evaporating solvents create an explosive environment.
• Do not spray near ignition sources such as static elec­ tricity sparks, naked flames, pilot lights, hot objects, engines, cigarettes, and sparks created by plugging in and unplugging electric cables or operating switches. These kinds of spark sources can lead to the combustion of the surrounding environment.
• Do not spray materials if it is not clear whether they might be dangerous. Unknown materials could create hazardous conditions.
• Do not spray boiling water. Spray only warm water (max. 55 °C) which is free from chemical additives.
• Wear additional personal protective equipment such as appropriate protective gloves and a protective mask or respirator when spraying or handling chemic­ Wearing personal protective equipment appropriate to the conditions reduces your exposure to hazardous substances.
  
• Take note of possible risks posed by the spray mater­ Observe the markings on the container or the man­ ufacturer’s information regarding the spray material, including the instructions about using personal pro­ tective equipment. You must comply with the manufac­turer’s instructions in order to reduce the risk of fire and of injury caused by poison, carcinogens, etc.
• Keep the mains plug and the spray system trigger switch free from paint and other liquids. Never hold the cable by its plug connection for support. Doing this could cause electric shock.
• Supervise children. This will ensure that children do not play with the fine spray system.

Products sold in GB only:
Your product is fitted with a BS 1363/A approved electric plug with an internal fuse (ASIA approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place by an authorized customer service agent. The replacement plug
should have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible shock hazard and should never be inserted into the main socket elsewhere.

Symbols

The sticker regarding the operation of the fine-spray system is located on the base station. The correct interpretation of the symbols helps you operate the fine-spray system quicker and more safely.

Step 3: Setting the airflow

Product Description and Specifications

Read all the safety and general instructions.
Failure to observe the safety and general instructions may result in electric shock, fire, and/or serious injury.
Please observe the illustrations at the beginning of this operating manual.

Intended Use
The power tool is intended for spraying all common paints: Emulsion and latex paints (wall paints), solvent-based and water-dilutable (recommended) lacquers, glazes, primers,
impregnations, clear lacquers (ALLPaint), oils, and water. The power tool is not suitable for use with caustic solutions, wood stains, acidic coating materials, disinfectants,  pesticides, and house paints.

Product Features
The numbering of the product features refers to the diagram of the power tool on the graphics page.

1. Spray gun
2. Air cap
3. Cap nut
4. Thumbwheel for spray material volume
5. Trigger switch
6. Lockring
7. Container for spray material
8. Spare container for spray material a)
9. Hose port (spray gun)
10. Nozzle cap (white: For “wall” application)
11. Nozzle cap (grey: For “wood” application)
12. Filling sieve
13. Transfer bucket a)
14. Nozzle needle
15. Container seal
16. Suction tube
17. Ventilation hole
18. Paint channel
19. Air hose
20. Bayonet lock
21. Base unit
22. Carrying strap
23. Carrying handle
24. Pin
25. Sliding switch for switching on/off and for airflow control
26. Air filter cover
27. Cleaning brush
28. Elastic band (hose holder)
29. Hose port (base unit)
30. Accessory compartment
31. Air filter

a) Accessories shown or described are not included with the product as standard. You can find the complete selection of accessories in our accessories range.

Technical Data

The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.

Noise/Vibration Information
Noise emission values were determined according to EN 62841-1.
Typically, the A-weighted sound pressure level of the power tool is 80 dB(A). Uncertainty K = 3 dB. The noise level when working can exceed the volume stated. Wear hearing protection!
Vibration total values  ah (triax vector sum) and uncertainty K determined according to 62841-1: ah < 2.5 m/s 2 , K = 1.5 m/s 2 
The vibration level and noise emission value given in these instructions have been measured in accordance with a standardized measuring procedure and may be used to compare power tools. They may also be used for a preliminary estimation of vibration and noise emissions.
The stated vibration level and noise emission value represent the main applications of the power tool. However, if the power tool is used for other applications, with different
application tools, or is poorly maintained, the vibration level and noise emission value may differ. This may significantly increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the times when the tool is switched off or when it is running but not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions over the total working period.
Implement additional safety measures to protect the operator from the effects of vibration, such as servicing the power tool and application tools, keeping their hands warm, and organizing workflows correctly.

Assembly

• Pull the plug out of the socket before carrying out any work on the power tool.
• Ensure that the spray gun and base unit are assembled completely and with all seals. Only this will ensure the function and safety of the fine-spray system.
• Ensure that a nozzle cap that was delivered with the spray gun is fitted. Only this will ensure the function and safety of the fine-spray system.

Connecting the Air Hose (see figures A1–A3) 
– Open the elastic band (28) and completely unwind the air hose (19).
Connecting the base unit:
– Insert a bayonet lock (20) of the air hose securely into the holes in the base unit port (29) according to the arrow marks.
– Turn the bayonet lock a quarter turn clockwise.
Connecting to the spray gun:
– Insert the second bayonet lock (20) of the air hose securely into the holes in the spray gun port (9) according to the arrow marks.
– Turn the bayonet lock a quarter turn clockwise.
Note: Remove the air hose (19) before pouring in spray material (quarter-turn of the bayonet lock (20) anticlockwise; pull the bayonet lock (20) out of the port (9)).

Changing the Nozzle Cap (see figures B1–B2) 
The fine-spray system is supplied with two nozzle caps:

Note: Check the spray material by stirring it before selecting the nozzle cap. Thin-viscosity material (e.g. wood paint) can be sprayed better with the grey nozzle cap (11). Thick-viscosity material (e.g. wood lacquer or wall paint) can be sprayed better with the white nozzle cap (10).

– To change the nozzle cap, unscrew the cap nut (3).
– Pull off the air cap (2).
– Unscrew the mounted nozzle cap.
– Open the air filter cover (26) and take the required nozzle cap out of the accessory compartment (30).
– Screw the required nozzle cap into the thread in the spray gun.
– Put the air cap (2) on the nozzle cap and tighten it with the cap nut (3).

Operation

• Pull the plug out of the socket before carrying out any work on the power tool.
• Products that are only sold in AUS and NZ: Use a residual current device (RCD) with a nominal residual current of 30 mA or less.

Work preparation

• Spraying on the sides of water bodies (lakes, rivers, etc.) or neighboring surfaces in the direct catchment area is not permitted.
• When purchasing paint, lacquer, and spray material, pay attention to their environmental compatibility.

Preparing the spray surface
The sprayed surface must be clean, dry, and grease-free.
– Roughen smooth surfaces and then remove the sanding dust.
When spraying, all non-covered surfaces can be contaminated by the spray mist. Therefore, thoroughly prepare the area around the surface to be sprayed:
– Carefully cover floors, furnishings, doors, and windows as well as door and window frames, etc. Painting substrate, for example, is recommended for covering the floors.
– Fix the cover material in place. A cover material that is not fixed in place securely can be detached or blown away by the powerful air jet.

• Carefully mask off plug sockets and switches. Uncovered plug sockets and switches may cause a short circuit and increase the risk of electric shock.

Preparing the spray material

• When diluting, make sure that the spray material and the diluting agent are compatible. When using a faulty diluting agent, lumps can develop that can lead to clogging of the spray gun.
• When diluting the spray material, make sure that the flashpoint of the mixture is above 55 °C again after diluting. Diluting substances such as solvent-based lacquers lower the flashpoint.
• Note the specifications of the paint manufacturer relating to sprayability, e.g. in the technical information sheet or datasheet. Make sure that you do not spray any paints that are not suitable according to the manufacturer’s specifications.
  – Stir the spray material thoroughly.
  Using spray material at room temperature will yield a better spray pattern.
  – Dilute the spray material if necessary.
  If the spray test does not produce a good spray pattern, dilute in 5 % increments until an optimal spray pattern is achieved.
  

Dilution table

Filling the spray material (see figures C1–C2)
Note: Remove the air hose (19) before pouring in spray material (quarter-turn of the bayonet lock (20) anticlockwise; pull the bayonet lock (20) out of the port (9)).
– When using large buckets, pour the spray material into a smaller transfer bucket (13) if necessary (e.g. 10 l wall paint into an empty 2.5 or 5.0 l bucket).
– Hold the spray gun in place with one hand and use the other hand to turn the container (7) towards the open symbol.
– Pull the spray gun off the container (7).– If you are using already opened spray material, place the thoroughly cleaned filling sieve (12) on the container (7) to hold back any lumps of paint when pouring in.
– Pour the spray material into the container (7) up to no more than the 1000 mark.
– Put the spray gun on the container (7). Turn the container (7) towards the close symbol until you hear the lock ring (6) engage. – Carry out a test-spray run on a test surface. If the spray pattern is optimal, you can begin spraying. or
If the spraying results are unsatisfactory or no paint is emitted: (see “Troubleshooting”, page 26)

Starting Operation

• Pay attention to the mains voltage. The voltage of the power source must match the voltage specified on the rating plate of the power tool.
• Make sure that the base unit cannot draw in dust or other contamination during operation.
• Make sure never to spray on the base unit.
• Stop spraying if fluid escapes from places other than the intended nozzle during spraying, and restore the spray gun to its proper condition. There is a risk of electric shock.
• Do not direct the fine-spray system against yourself, other persons, or animals.

Switching On (see figure D)
– Check whether the correct nozzle cap is fitted (see “Changing the Nozzle Cap (see figures B1–B2)”, page 22).
– Plug the mains plug into a plug socket.
– Grasp the spray gun by the handle and point it at the target area.
– Set the sliding switch (25) to the required application to regulate the airflow (see “Setting the Air Flow (see figure D)”, page 24).
– Pull the trigger switch (5) on the spray gun.
Note: Air always flows out at the air cap (2) when the base unit is switched on.

Switching Off
– Let go of the trigger switch (5) and slide the sliding switch (25) all the way to the left (position ◯).
– Pull the mains plug from the plug socket.

Working Advice
Spraying (see figures E–H)
Note: Pay attention to the wind direction when you are using the power tool outdoors.
– Firstly, carry out a spray test and adjust the spray pattern and the spray material volume according to the spray material. For adjustments, see the following
sections.
– Make sure to hold the spray gun with a uniform clearance of 20–25 cm vertical to the object being sprayed.
– Begin the spraying procedure outside the target area.
– Move the spray gun evenly horizontally or vertically according to the spray pattern configuration.
Even surface quality can be achieved when the spray paths overlap by 4–5 cm.
– When spraying horizontal objects or spraying overhead, hold the spray gun at a slight angle and move back from the sprayed surface.
Risk of tripping! Be aware of potential obstacles. 
– Avoid interruptions when spraying the target area. Guiding the spray gun evenly will provide uniform surface quality.
A non-uniform spraying angle and distance will lead to a heavy formation of paint mist and consequently an uneven surface.
– End the spraying procedure outside the target area.
Never completely empty the container for the spray material by spraying. If the suction tube is no longer immersed in the spray material, the spray jet will be interrupted and this will result in an inconsistent surface.
– After breaks or refilling the container (7), check the nozzle cap (10)/(11) and the air cap (2) and clean them if required.
– If spray material settles on the air cap (2) or the nozzle cap, clean the components with the supplied cleaning brush (27) or a commercially available washing-up brush.

Setting the spray pattern (see figure I)
• Never actuate the trigger switch (5) while adjusting the air cap (2).
– Turn the air cap (2) to the required position.

Setting the spray material quantity (see figure J) (PAINTVolume)
– Turn the thumbwheel (4) to set the required spray material quantity: Settings 1/2/3: “Wood” application, Settings 3/4/5: “Wall” application.
– Start with a spray test at setting 1 and increase the spray material volume until the required spray pattern is achieved. If a satisfactory spray pattern is not achieved, dilute the spray material in 5 % increments (see “Preparing the spray material”, page 22).
Please note: The intensity of the paint application is highly dependent on the moving speed.

Setting the Air Flow (see figure D) (AIRVolume)
– Set the sliding switch (25) to the appropriate application to set the correct airflow and pressure for the spray material used.

Dampening Wallpaper
To make it easier to remove old wallpaper, you can spray warm water on the wallpaper (max. 55 °C). Use the grey nozzle cap (11) to do so.

Work breaks and transport (see figure K–L)
A carrying handle (23) and a carrying strap (22) are fitted to the base unit to enable easy transport of the fine-spray system.
You can hang the base unit (21) across your shoulder during work using the carrying strap (22).
The spray gun (1)can be put down on a flat work surface during breaks. No spray material can leak out.

• Always put the spray gun upright on a flat surface when it is filled with spray material. Spray material can leak out from a spray gun if it is lying down.

Maintenance and Service

Maintenance and Cleaning

• Pull the plug out of the socket before carrying out any work on the power tool.
• To ensure safe and efficient operation, always keep the power tool and the ventilation slots clean.

In order to avoid safety hazards, if the power supply cord needs to be replaced, this must be done by Bosch or by an after-sales service center that is authorized to repair Bosch
power tools.

• Thoroughly clean the individual parts of the fine-spray system immediately after each use, especially all paint-carrying components. Proper cleaning is a prerequisite for the faultless and safe operation of the spray gun.  No warranty claims will be accepted if the cleaning has not been done at all or has not been done properly.

Cleaning After Using Water-Based Paints (see figure M)
Always clean the spray gun and the spray material container with warm water.
Never clean the nozzle and air holes in the spray gun with pointed objects.
– Switch off the base unit (21) and remove the air hose (19) from the spray gun (1).
– Remove the container (7) from the spray gun (1).
Hold the container (7) underneath the suction tube (16) and pull the trigger switch (5) on the spray gun so that the spray material can flow back into the container.
– Empty the container (7).
The spray material can be stored in an airtight, sealed paint container for other applications. Use the spare container (8) with a cover or the original spray material container, for example, for this purpose.
– Clean the container (7).
– Remove the suction tube (16) with the container seal (15) and rinse it thoroughly.
Reattach the suction tube (16) with the container seal (15) to the spray gun.
– Fill the container (7) with warm water and fit it to the spray gun (1)again.
– Connect the air hose (19) to the spray gun (1)again.
– Spray until only clear water comes out. You may have to fill the container with warm water again.
– Remove the air hose (19) from both the base unit (21) and the spray gun (1).
– Clean the base unit if necessary with a moistened cloth and then remove the base unit (21) and the air hose (19) from the immediate cleaning environment.
– Remove the cap nut (3), the air cap (2), the nozzle cap used (10)/(11), and the suction tube (16) with the container seal (15).
– Clean all paint-carrying parts in a bucket with warm water using the cleaning brush (27) or with a commercially available washing-up brush. Also, clean the paint channel (18) of the spray gun (1).
– Check that the suction tube (16) and the container seal (15) are free of spray material and undamaged.
– Clean the ventilation hole (17) using the cleaning brush (27).
– If required, clean the filling sieve (12) thoroughly with warm water.
– Clean the outside of the container (7) and the spray gun (1)with a damp cloth.
– Allow all components to dry thoroughly before assembling them.
– Reassemble the fine-spray system in reverse order.
Slide the container seal (15) upwards again into the groove of the suction tube (16).
Ensure that the container seal is positioned precisely all-around in the suction tube groove in order to seal the spray gun correctly.
Make sure that you slide the suction tube (16) all the way back onto the paint channel (18).

Cleaning After Using Solvent-Based Paints (see figure M) 
Always clean the spray gun and the container for the spray material with the respective diluting agent for the spray material being used.
Never clean the nozzle and air holes in the spray gun with pointed objects.

Wear suitable gloves during cleaning work involving solvents and solvent-based paints.
– Switch off the base unit (21) and remove the air hose (19) from the spray gun (1).
– Clean the base unit if necessary with a cloth moistened with a diluting agent and then remove the base unit (21) and the air hose (19) from the immediate cleaning environment.
– Remove the container (7) from the spray gun (1). Hold the container (7) underneath the suction tube (16) and pull the trigger switch (5) on the spray gun so that the
spray material can flow back into the container.
– Empty the container (7).
The spray material can be stored in an airtight, sealed paint container for other applications. Use the spare container (8) with a cover or the original spray material container, for example, for this purpose.
– Clean the container (7).
– Remove the suction tube (16) with the container seal (15) and rinse it thoroughly.
Reattach the suction tube (16) with the container seal (15) to the spray gun.
– Fill the container (7) halfway with solvent and fit it to the spray gun (1)again.
– Shake the spray gun several times.
Make sure that you do not spray the diluting agent. There is a risk of explosion.
– Remove the container (7) from the spray gun (1)and empty it completely into a sealable material tin.
– Remove the cap nut (3), the air cap (2), the nozzle cap used (10)/(11), and the suction tube (16) with the container seal (15).
– Clean all paint-carrying parts in a bucket with a diluting agent using the cleaning brush (27) or with a commercially available washing-up brush. Also, clean the paint channel (18) of the spray gun (1).
– Check that the suction tube (16) and the container seal (15) are free of spray material and undamaged.
If required, clean the container seal (15) again with a diluting agent.
– Clean the ventilation hole (17) using the cleaning brush (27).
– If required, clean the filling sieve (12) thoroughly with a diluting agent.
– Clean the outside of the container (7) and the spray gun (1)with a cloth moistened with a diluting agent.
– Allow all components to dry thoroughly before assembling them.
– Reassemble the fine-spray system in reverse order.
Slide the container seal (15) upwards again into the groove of the suction tube (16).
Ensure that the container seal is positioned precisely all-around in the suction tube groove in order to seal the spray gun correctly.
Make sure that you slide the suction tube (16) all the way back onto the paint channel (18).

Cleaning the air filter (see figure N)
The air filter (31) must be cleaned occasionally. The air filter must be replaced if it is heavily contaminated.
– Open the air filter cover (26).
– Remove the air filter (31).
– Light contamination:
Knock on the air filter (31).
or
Heavy contamination: Clean the air filter (31) under running water and subsequently leave it to dry thoroughly, in order to prevent mold from forming.
or
Replace the air filter (31).
– Reinsert the air filter.
– Close the air filter cover (26) again.
• Never use the fine-spray system without an air filter. Dirt particles may get into the motor compartment and damage it.

Material Disposal
Contaminated diluting agent, remnants of spray material, and, if applicable, remnants of diluting agent must be disposed of properly and in an environmentally friendly manner. Observe the manufacturer’s disposal information and the local regulations for disposal of hazardous waste.
Chemicals harmful to the environment may not be disposed of in soil, groundwater, or bodies of water. Never pour chemicals harmful to the environment into the sewerage system.

Storage
– Before putting the fine-spray system into storage, thoroughly clean the fine-spray system and allow all parts to dry completely before assembling them.
If the fine-spray system is not being used, the elastic band (28) together with the pin (24) on the base unit (21) serve as a practical storage option for the air hose (19) (see figure O).

Troubleshooting

Spray material dripping at the nozzle capDeposit of spray material on the nozzle cap (10)/(11), the nozzle needle (14), and the air cap (2)No spray material coming out of the nozzle cap sliding switch (25) is in position 0

After-Sales Service and Application Service
Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts. You can find explosion drawings and information
on spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you with any questions about our products and their accessories.
In all correspondence and spare parts orders, please always include the 10‑digit article number given on the nameplate of the product.

Great Britain 
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail:

You can find further service addresses at: www.bosch-pt.com/serviceaddresses
Disposal
Spray guns, electrical units, accessories, and packaging should be sorted for environmentally friendly recycling.
Do not dispose of power tools along with the household waste.

Only for EU countries:
According to the European Directive 2012/19/EU on Waste Electrical and Electronic Equipment and its implementation into national law, power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly manner.

Only for the United Kingdom: 
According to Waste Electrical and Electronic Equipment Regulations 2013 (2013/3113), power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly manner.

Robert Bosch Power Tools GmbH
70538 Stuttgart
GERMANY
www.bosch-pt.com

Declaration of Conformity

Robert Bosch Ltd. Broadwater Park, North Orbital Road, Uxbridge UB9 5HJ, United Kingdom, as authorized representative acting on behalf of Robert Bosch Power Tools GmbH, 70538 Stuttgart, Germany

Place of issue: Uxbridge
Date of issue: 11/05/2021
Bosch Power Tools
1 609 92A 685 | (09.09.2021)